Description : The initial gap between the extra full-length leaf and the graduated-length leaf before the assembly, is called as (A) clearance (B) nip (C) gap
Last Answer : (B) nip
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined
Last Answer : (b) 4674.1N
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : Nipping is defined as leaving the gap between full length leaf and graduated length leaf. a) True b) False
Last Answer : b) False
Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated
Last Answer : b) No
Description : In manual assembly, cost of screw is higher than the cost of driving a screw. a) True b) False
Description : Multi leaf springs are not recommended for automobile and rail road suspensions. a) True b) False
Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)
Last Answer : (A) cos α = (dr + dp)/(dr + df)
Description : Needles bearing consist of rollers of small diameter and very small length. (a) True (b) False
Last Answer : (b) False
Description : Needles bearing consist of rollers of small diameter and very small length. a) True b) False
Description : Compressed length is smaller than the solid length. a) True b) False
Description : Just graduated college and have some extra money to go on a trip. where should I go and why?
Last Answer : It’s such a generic answer but I would travel around Europe. I’d learn some new languages, see lots of famous monuments and museums, and see how a whole lot of other people live. And congrats on graduation!
Description : A rolling contact bearing is specified as X307. Determine the series. a) Extra light series b) Light series c) Medium series d) Heavy series
Last Answer : c) Medium series
Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned
Last Answer : (d) all the mentioned
Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)
Last Answer : (A) Approaches yield point
Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three
Last Answer : (D) All the three
Description : The resultant axial force on bolt depends upon (A) Initial tension (B) External applied load (C) Stiffness of bolt and parts held by bolt (D) All three factors
Last Answer : (D) All three factors
Description : Multi-leaf springs are used in (A) automobile suspension (B) railroad suspension (C) both (A) and (B) (D) none of the above
Last Answer : (C) both (A) and (B)
Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above
Last Answer : (A) bending stress
Description : The longest leaf in Semi-elliptic leaf spring is known as (A) chief leaf (B) master leaf (C) major leaf (D) higher leaf
Last Answer : (B) master leaf
Description : The type of spring used to absorb and release energy in mechanical watches is (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring
Last Answer : (C) Spiral spring
Description : The type of spring used to achieve greater load carrying capacity within given space is (A) Spiral spring (B) Springs in series (C) Multi-leaf spring (D) Concentric springs
Last Answer : (D) Concentric springs
Description : The type of spring used to measure weights in spring balance is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring
Last Answer : (A) Helical extension spring
Description : The type of spring used in door hinges is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Helical torsion spring
Last Answer : (D) Helical torsion spring
Description : The type of spring used to absorb shocks and vibrations in vehicles is, (A) Helical extension spring (B) Multi-leaf spring (C) Spiral spring (D) Belleville (coned disk) spring
Last Answer : (B) Multi-leaf spring
Description : The longest leaf in a leaf spring is called centre leaf. a) It is called middle leaf b) It is called master leaf c) Yes d) None of the listed
Last Answer : b) It is called master leaf
Description : Bending stress in graduated length leaves are more than that in full length leaves. (a) Yes (b) No (c) In some cases (d) Can’t be stated
Last Answer : (b) No
Description : Keyed joints never lead to stress concentration on shafts. a) True b) False
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : The operation of flywheel is continuous. a) True b) False
Last Answer : a) True
Description : Flywheel and governor can be interchanged. a) True b) False
Description : Flywheels are used in punching and shear operation. a) True b) False
Description : Is use of a flywheel recommended when a large motor is required only for a small instant of time? a) True b) False
Description : The dynamic load-carrying capacity of a bearing is defined as the radial load in radial bearings that can be carried for a minimum life of 1000 revolutions. (a) True (b) False
Description : For the majority of bearings, actual life is considerably greater than rated life. (a) True (b) False
Last Answer : (a) True
Description : The life of an individual ball bearing is the time period for which it works without any signs of failures. (a) True (b) False
Description : Stribeck equation gives the dynamic load capacity of the bearing. (a) True (b) False
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Description : A cylinder roller creates lesser noise than a deep groove ball bearing. (a) True (b) False
Description : Angular contact bearing can take thrust as well as radial loads. (a) True (b) False
Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False
Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true
Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A
Description : Assertion (A): In hydrodynamic journal bearings, the rotating journal is held in floating condition by the hydrodynamic pressure developed in the lubricant. Reason (R): Lubricant flows in a converging-diverging channel. [IES-1994] ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are individually true and R is the correct explanation of A
Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (c) A is true but R is false
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true
Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true
Last Answer : (a) Both A and R are true and R is the correct explanation of A
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False