The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

The name of the welded joint made by placing the plates edge to edge is

(i) Fillet welded joint

(ii) Butt welded joint

(iii) Fillet-Butt welded joint

(iv) None
by

1 Answer

Answer :

(ii) Butt welded joint
by

Related questions

By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (i) Fillet welded joint

Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Last Answer : iii. 5/8”

Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Last Answer : iii. 3/8”

Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (ii) Lap joint

Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (i) Butt joint

Out of the followings, which welded joint is more stronger (i) Butt joint (ii) Lap joint (iii)Screwed joint

Description : Out of the followings, which welded joint is more stronger (i) Butt joint (ii) Lap joint (iii)Screwed joint

Last Answer : (i) Butt joint

Why are butt welded joints longitudinal joints ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements iv. None

Description : Why are butt welded joints longitudinal joints ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements iv. None

Last Answer : i. High strength requirements

Joint which does not fall under lap joint category (i)Transverse fillet (ii) Parallel fillet (iii) Circular fillet (iv) None

Description : Joint which does not fall under lap joint category (i)Transverse fillet (ii) Parallel fillet (iii) Circular fillet (iv) None

Last Answer : (iv) None

The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (d) shear strength

In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (c) 2 × Throat of weld

The advantage of a welded joint over a riveted joint is (i) Introduce residual stresses (ii) Requires highly skilled labor and supervision (iii) Lighter in weight (iv) None

Description : The advantage of a welded joint over a riveted joint is (i) Introduce residual stresses (ii) Requires highly skilled labor and supervision (iii) Lighter in weight (iv) None

Last Answer : (iii) Lighter in weight

Internal defects in a welded joint can be found by a process called (i) Tension test (ii) Visual inspection (iii) Radio graphing (iv) None

Description : Internal defects in a welded joint can be found by a process called (i) Tension test (ii) Visual inspection (iii) Radio graphing (iv) None

Last Answer : (iii) Radio graphing

One which is applicable to a welded joint (i)Less rigidity (ii) Heavy (iii) Difficult process (iv) None

Description : One which is applicable to a welded joint (i)Less rigidity (ii) Heavy (iii) Difficult process (iv) None

Last Answer : (iv) None

Type of welded joint which do not exit (i) Groove type (ii) Spot type (iii)Plug type (iv) Surface type

Description : Type of welded joint which do not exit (i) Groove type (ii) Spot type (iii)Plug type (iv) Surface type

Last Answer : (iv) Surface type

Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None

Description : Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None

Last Answer : i. Longitudinal stress

Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None

Description : Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None

Last Answer : i. 6%

Strength of a welded joint increases by radio graphing by i. 10 % ii. 12% iii. 15% iv. None

Description : Strength of a welded joint increases by radio graphing by i. 10 % ii. 12% iii. 15% iv. None

Last Answer : ii. 12%

A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Last Answer : (a) butt weld

The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (b) Throat of weld

Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None

Description : Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None

Last Answer : (i) Shear stress

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Last Answer : (i)0.707 tl

Term which is not applicable to a welded joint (i) Higher efficiency (ii)Easy process (iii) Faster process

Description : Term which is not applicable to a welded joint (i) Higher efficiency (ii)Easy process (iii) Faster process

Last Answer : (ii)Easy process

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

Last Answer : a) My/I

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

Lap welded joints used in circumferential joints because of ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements

Description : Lap welded joints used in circumferential joints because of ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements

Last Answer : ii. Low strength requirements

Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year showing the cost at that time relative to a certain base year (C) Turnover ratio of a chemical plant is the ratio of gross annual sales to the fixed capital investment (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Description : Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year ... butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Last Answer : (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

The angle of V-welded joint in a pressure vessel 30 to 45 0 40 to 55 0 55 to 70 0 None

Description : The angle of V-welded joint in a pressure vessel 30 to 45 0 40 to 55 0 55 to 70 0 None

Last Answer : 55 to 70 0

Welded joints are a. Hinged joint b. Rigid joint c. Freely supported joint

Description : Welded joints are a. Hinged joint b. Rigid joint c. Freely supported joint

Last Answer : b. Rigid joint

Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None

Description : Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None

Last Answer : c. No change in tension strength

The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None

Description : The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None

Last Answer : a. Greater

Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Description : Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Last Answer : c. Greater

Longitudinal welded joint fails by  Longitudinal stress  Radial stress  Hoop stress  None

Description : Longitudinal welded joint fails by  Longitudinal stress  Radial stress  Hoop stress  None

Last Answer :  Hoop stress

The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False

Description : The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False

Last Answer : b) False

As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint. (A) Butt (B) Lap (C) Welded (D) None of these

Description : As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint. (A) Butt (B) Lap (C) Welded (D) None of these

Last Answer : (B) Lap

Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding

Description : Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding

Last Answer : (iv) Machine used in welding

When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

Description : When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

Last Answer : (D) Double riveted double cover butt joint

Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Last Answer : b) False

A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Last Answer : b) False

Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Last Answer : c. Triangular

The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Last Answer : c. 45 0

Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Last Answer : b. 0.707x leg

Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Description : Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Last Answer :  None

Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Last Answer : b) False

Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Last Answer : a) t =h Cos (45’)

The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Last Answer : a) Leg

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False