A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed

A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress

induced in the welds can be given by

a) My/I

b) 2My/I

c) My/2I

d) None of the listed
by

1 Answer

Answer :

a) My/I
by

Related questions

While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4

Description : While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4

Last Answer : b) None of the listed

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False

Description : The following bracket is welded to the vertical column. The joint undergoes torsional stresses. a) True b) False

Last Answer : b) False

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Description : Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Last Answer :  None

Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None

Description : Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None

Last Answer : (i) Shear stress

Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (d) shear strength

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (ii) Butt welded joint

By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (i) Fillet welded joint

Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Description : Double full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 3/8” iii. 5/8” iv. None

Last Answer : iii. 5/8”

Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Description : Single full fillet welded joint cannot be used for a plate thickness greater than i. 1/8” ii. 2/8” iii. 3/8” iv. None

Last Answer : iii. 3/8”

In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (c) 2 × Throat of weld

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed

Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed

Last Answer : b) 360/t

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : b) 32M/πdɜ

When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : b) 32M/πdɜ

Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t

Description : Calculate the moment of inertia about the axis parallel to welds and shift it to CG by considering thickness of welds t. a) tɜ+2000t b) None of the listed c) 250000 t d) 125000 t

Last Answer : c) 250000 t

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (C) Bending stress

When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress

Last Answer : (D) Torsional shear stress

The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Last Answer : a) Leg

Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Last Answer : a) t =h Cos (45’)

Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Butt welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None

Description : Circumferential welded joint fails by i. Longitudinal stress ii. Radial stress iii. Hoop stress iv. None

Last Answer : i. Longitudinal stress

Longitudinal welded joint fails by  Longitudinal stress  Radial stress  Hoop stress  None

Description : Longitudinal welded joint fails by  Longitudinal stress  Radial stress  Hoop stress  None

Last Answer :  Hoop stress

When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Description : When a column is subjected to an eccentric load, the stress induced in the column will be (a) direct stress only (b) bending stress only (c) shear stress only (d) direct and bending stress both

Last Answer : (d) direct and bending stress both

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : c) 16M/πdɜ

When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ

Last Answer : c) 16M/πdɜ

Magnetic crack detection method in the welds is destructible examination. a) True b) False

Description : Magnetic crack detection method in the welds is destructible examination. a) True b) False

Last Answer : b) False

The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

Description : The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils

Last Answer : (A) Inner surface of the coil

When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing stress is more than crushing stress induced in the threads c. crushing stress induced is equal to permissible crushing stress d. all of the above

Description : When a coupler nut is subjected to crushing stress, crushing failure can be avoided if _____ a. crushing stress induced is more than permissible crushing stress in the nut b. permissible crushing ... threads c. crushing stress induced is equal to permissible crushing stress d. all of the above

Last Answer : b. permissible crushing stress is more than crushing stress induced in the threads

The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress

Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress

Last Answer : (C) Twice of shear stress

The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress

Last Answer : 1. direct tensile stress and bending stress

The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress

Description : The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress

Last Answer : (A) Direct tensile stress and bending stress

The bending stress in a curved beam is A. Zero at the centroidal axis B. Zero at the point other than centroidal axis C. Maximum at the neutral axis D. None of these

Description : The bending stress in a curved beam is A. Zero at the centroidal axis B. Zero at the point other than centroidal axis C. Maximum at the neutral axis D. None of these

Last Answer : B. Zero at the point other than centroidal axis

The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above

Last Answer : (A) bending stress

Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Last Answer : b) No

A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types

Description : A shaft is subjected to the...... A. Normal stress B. Bending stress C. Shear stress D. Combine stress E. All types

Last Answer : E. All types