Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed
Last Answer : b) 1.21P/hl
Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed
Last Answer : a) PSinθ(Sinθ+Cosθ)/hl
Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed
Last Answer : a) t =h Cos (45’)
Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed
Last Answer : a) Leg
Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None
Last Answer : b. 0.707x leg
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None
Last Answer : (i)0.707 tl
Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld
Last Answer : (b) Throat of weld
Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld
Last Answer : (c) 2 × Throat of weld
Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed
Last Answer : b) 360/t
Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Last Answer : b) False
Description : If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm
Last Answer : c) 24mm
Description : During erection, the pile of length is supported by a crane at a distance of (A) 0.207 l (B) 0.293 l (C) 0.707 l (D) 0.793 l
Last Answer : (C) 0.707 l
Description : Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding
Last Answer : (iv) Machine used in welding
Description : Different parts of a weld symbol are (i) Arrow, center line and back part (ii) Arrow, body line and length (iii) Arrow, body line and tail (iv)None
Last Answer : (iii) Arrow, body line and tail
Description : Hard peening is a) Hammering the weld across the length while the joint is hot b) Hammering the weld along the length while the joint is hot c) Hammering the weld along the length while the joint is cold d) Hammering the weld across the length while the joint is cold
Last Answer : b) Hammering the weld along the length while the joint is hot
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : When an internal mouthpiece is running free, the discharge through the mouthpiece is (where a = Area of mouthpiece, and H = Height of liquid above the mouthpiece) (A) 0.5 a. gH (B) 0.707 a. gH (C) 0.855 a. gH (D) a. gH
Last Answer : Answer: Option A
Description : If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel
Last Answer : d) Longitudinal or Parallel
Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed
Last Answer : d) None of the listed
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None
Last Answer : c. 45 0
Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False
Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False
Description : Plug weld is a. Rectangular b. Square c. Triangular d. None
Last Answer : d. None
Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None
Last Answer : c. Triangular
Description : Quantity is not a part of the weld symbol (i)Dark circle (ii) Open circle (iii) Angle of weld (iv)Starting and stopping allowance for welding
Last Answer : (iv)Starting and stopping allowance for welding
Description : Term which is not a part of the weld symbol (i) Tail (ii) Arrow (iii) Temperature of welding (iv) None
Last Answer : (iii) Temperature of welding
Description : A weld symbol is necessary because of (i) Aesthetic sense (ii) Finishing (iii) Manufacturing (iv) None
Last Answer : (iii) Manufacturing
Description : Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False
Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False
Description : Convex weld is generally preferred over normal weld. a) True b) False
Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.
Last Answer : (a) butt weld
Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False
Description : For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°
Last Answer : (c) 45°
Description : The strain energy stored in a spiral spring is given by? a) 12M2L/Ebtɜ b) 6M2L/Ebtɜ c) 8M2L/Ebtɜ d) None of the listed
Last Answer : b) 6M2L/Ebtɜ
Description : Angle of rotation o arbour with respect to drum is given by? a) None of the listed b) 12ML/Ebtɜ c) 8 ML/Ebtɜ d) 16ML/Ebtɜ
Last Answer : b) 12ML/Ebtɜ
Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed
Last Answer : a) My/I
Description : When the shaft is subjected to pure torsional moment, the torsional stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ
Last Answer : c) 16M/πdɜ
Description : When the shaft is subjected to pure bending moment, the bending stress is given by? a) None of the listed b) 32M/πdɜ c) 16M/πdɜ d) 8M/πdɜ
Last Answer : b) 32M/πdɜ
Description : Which of the following in 8085 microprocessor performs HL = HL + DE ? (A) DAD D (B) DAD H (C) DAD B (D) DAD SP
Last Answer : (A) DAD D
Description : The average heat transfer co-efficient over the entire length of the plate (ha ) and the local heat transfer co-efficient (hL ), in case of heat transfer over a flat plate in laminar zone is related as (A) ha = 0.8hL (B) ha = 2hL (C) ha = hL (D) ha = 5hL
Last Answer : (B) ha = 2hL
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : A column of length l is fixed at both ends. The equivalent length of the column is (A) l/2 (B) l/√2 (C) l (D) 2 l
Last Answer : (A) l/2