Knuckle Joint can’t be used to connect two intersecting rods. a) Yes b) No, it can’t be used c) It can be used with some modificatios d) It is expensive and hence isn’t used

Knuckle Joint can’t be used to connect two intersecting rods.

a) Yes

b) No, it can’t be used

c) It can be used with some modificatios

d) It is expensive and hence isn’t used
by

1 Answer

Answer :

b) No, it can’t be used
by

Related questions

The knuckle joint is used to connect the... A. Two roads whose Axes are coincide or intersecting and lies in single plane. B. Two roads whose Axes are coincide or intersecting and lies in multiple plane. C. Two roads whose Axes are parallel or intersecting and lies in single plane. D. None of the above

Description : The knuckle joint is used to connect the... A. Two roads whose Axes are coincide or intersecting and lies in single plane. B. Two roads whose Axes are coincide or intersecting and lies in multiple ... Two roads whose Axes are parallel or intersecting and lies in single plane. D. None of the above

Last Answer : A. Two roads whose Axes are coincide or intersecting and lies in single plane.

The real application of knuckle joint is used to connect three rods - two with forks and a third with the eye. A. True B. False

Description : The real application of knuckle joint is used to connect three rods - two with forks and a third with the eye. A. True B. False

Last Answer : A. True

Knuckle Joint is used to connect the two rods whose axes are coincide or intersect and lies in the same plane. A. True B. False

Description : Knuckle Joint is used to connect the two rods whose axes are coincide or intersect and lies in the same plane. A. True B. False

Last Answer : A. True

A knuckle joint can be used in valve mechanism of a reciprocating engine. a) Yes b) No c) Yes but there are stress probles d) No as it is very dangerous to use

Description : A knuckle joint can be used in valve mechanism of a reciprocating engine. a) Yes b) No c) Yes but there are stress probles d) No as it is very dangerous to use

Last Answer : a) Yes

A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these

Description : A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these

Last Answer : A. Co-axial

Cotter joint is going to be use to connect the two rods for torque transmission purpose. a) True b) False

Description : Cotter joint is going to be use to connect the two rods for torque transmission purpose. a) True b) False

Last Answer : b) False

Cotter joint can be used to connect two rods for torque transmission purpose. true /false. a) True b) False

Description : Cotter joint can be used to connect two rods for torque transmission purpose. true /false. a) True b) False

Last Answer : b) False

Cotter joint can be used to connect two rods for torque transmission purpose. a) True b) False

Description : Cotter joint can be used to connect two rods for torque transmission purpose. a) True b) False

Last Answer : b) False

The knuckle joint is used two joint between the tie bars in roof trusses. A. True B. False

Description : The knuckle joint is used two joint between the tie bars in roof trusses. A. True B. False

Last Answer : A. True

A knuckle joint is unsuitable for two rotating shafts, which transmit torque a) True b) False

Description : A knuckle joint is unsuitable for two rotating shafts, which transmit torque a) True b) False

Last Answer : a) True

Within the external combination engine, a piston rod is usually connected to the cross head by means of....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Description : Within the external combination engine, a piston rod is usually connected to the cross head by means of....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Last Answer : A. Cotter joints

The knuckle joint is made up of... A. Cast iron B. stainless Steel C. Teflon D. All of the above

Description : The knuckle joint is made up of... A. Cast iron B. stainless Steel C. Teflon D. All of the above

Last Answer : D. All of the above

The split - pin is used in... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Description : The split - pin is used in... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Last Answer : B. Knuckle joint

The joints between link of a suspension bridge, which of the following joints used.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Description : The joints between link of a suspension bridge, which of the following joints used.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Last Answer : B. Knuckle joint

The diameter of knuckle pin in the knuckle joint is usually... A. 0.5 d B. 0.8 d C. 1.5 d D. d

Description : The diameter of knuckle pin in the knuckle joint is usually... A. 0.5 d B. 0.8 d C. 1.5 d D. d

Last Answer : D. d

To joining the links of a bicycle chain which of the following joint is used. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Description : To joining the links of a bicycle chain which of the following joint is used. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Last Answer : B. Knuckle joint

Which of the following are parts of knuckle joint. A. Eye B. Pin C.Fork D. All of the above

Description : Which of the following are parts of knuckle joint. A. Eye B. Pin C.Fork D. All of the above

Last Answer : D. All of the above

Forked - pin joints is also called as... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Description : Forked - pin joints is also called as... A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Last Answer : B. Knuckle joint

The valve rod connected in steam engine by using.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Description : The valve rod connected in steam engine by using.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Last Answer : B. Knuckle joint

Maximum rod connecting limit by using knuckle joint is . A. 2 B. 3 C. 4 D. 5

Description : Maximum rod connecting limit by using knuckle joint is . A. 2 B. 3 C. 4 D. 5

Last Answer : B. 3

In steam engine, the piston rod is usually connected to the cross head by means of a....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Description : In steam engine, the piston rod is usually connected to the cross head by means of a....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Last Answer : A. Cotter joints

Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Description : Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Last Answer : d) Each of the mentioned

A knuckle joint is also called socket pin joint. a) True b) False

Description : A knuckle joint is also called socket pin joint. a) True b) False

Last Answer : b) False

A maximum of how many roads may be connected using a knuckle joint? a) 2 b) 3 c) 4 d) 5

Description : A maximum of how many roads may be connected using a knuckle joint? a) 2 b) 3 c) 4 d) 5

Last Answer : b) 3

Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Description : Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Last Answer : b) False

Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Description : Oldham coupling i used to connect two shafts having intersecting axes. a) True b) False

Last Answer : b) False

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Description : Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Last Answer : b) No, it is done up to plastic stage

The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Description : The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Last Answer : b) It is closed coiled spring

Teflon can be used for manufacturing of knuckle joints. A. True B. False

Description : Teflon can be used for manufacturing of knuckle joints. A. True B. False

Last Answer : A. True

A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Description : A bushed-pin type flange coupling is used (A) For intersecting shafts (B) When the shafts are not in exact alignment (C) For small shafts rotating at slow speeds (D) For parallel shafts

Last Answer : (B) When the shafts are not in exact alignment

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Last Answer : b) No

Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Last Answer : b) No, fusion doesn’t require

Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Last Answer : b) No, they are subjected to compressive forces only

Can the cotter joint be used to connect slide spindle and fork of valve mechanism? a) True b) False

Description : Can the cotter joint be used to connect slide spindle and fork of valve mechanism? a) True b) False

Last Answer : a) True

The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Description : The deep groove ball bearing has immense rigidity. (a) True (b) No, it has point contact and hence low rigidity (c) It has surface contact (d) It has line contact

Last Answer : (b) No, it has point contact and hence low rigidity

Deep groove ball bearing has immense rigidity. a) True b) No it has point contact and hence low rigidity c) It has surface contact d) It has line contact

Description : Deep groove ball bearing has immense rigidity. a) True b) No it has point contact and hence low rigidity c) It has surface contact d) It has line contact

Last Answer : b) No it has point contact and hence low rigidity

The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated

Last Answer : a) Yes

Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Last Answer : (c) They create very less noise

Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Last Answer : b) They create very less noise

The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root

Description : The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root

Last Answer : b) No, it is directly proportional

Taper is made cotter and slot on both the side. A. Yes B. No

Description : Taper is made cotter and slot on both the side. A. Yes B. No

Last Answer : B. No

Filler material is used in electric resistance welding. a) Yes b) No filler material used c) Depends on the type of welding d) None of the listed

Description : Filler material is used in electric resistance welding. a) Yes b) No filler material used c) Depends on the type of welding d) None of the listed

Last Answer : b) No filler material used

Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Last Answer : b) No

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Last Answer : b) No

The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted

Last Answer : (a) Yes