Forge welding involves heating of parts to elastic stage and joint is prepared by impact force. a) Yes b) No, it is done up to plastic stage c) Heating is done up to boiling point d) None of the listed

Forge welding involves heating of parts to elastic stage and joint is prepared by impact force.

a) Yes

b) No, it is done up to plastic stage

c) Heating is done up to boiling point

d) None of the listed
by

1 Answer

Answer :

b) No, it is done up to plastic stage
by

Related questions

Filler material is used in electric resistance welding. a) Yes b) No filler material used c) Depends on the type of welding d) None of the listed

Description : Filler material is used in electric resistance welding. a) Yes b) No filler material used c) Depends on the type of welding d) None of the listed

Last Answer : b) No filler material used

All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed

Last Answer : b) No, fusion doesn’t require

Which type of welding is generally used in automobile sector? a) Electric arc welding b) Electric resistance welding c) Gas welding d) Forge welding

Description : Which type of welding is generally used in automobile sector? a) Electric arc welding b) Electric resistance welding c) Gas welding d) Forge welding

Last Answer : b) Electric resistance welding

Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding

Description : Rails in the field are generally welded by using a) Thermit welding b) Gas welding c) Electric arc welding d) Forge welding

Last Answer : a) Thermit welding

The electric arc welding is a type of ............. welding. (a) forge (b) fusion

Description : The electric arc welding is a type of ............. welding. (a) forge (b) fusion

Last Answer : b) fusion

In forging, metal is in which of the following stage? a) Elastic b) Plastic c) Can be in any stage d) Rigid

Description : In forging, metal is in which of the following stage? a) Elastic b) Plastic c) Can be in any stage d) Rigid

Last Answer : b) Plastic

Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed

Last Answer : b) It is measured in uncompressed state

The longest leaf in a leaf spring is called centre leaf. a) It is called middle leaf b) It is called master leaf c) Yes d) None of the listed

Description : The longest leaf in a leaf spring is called centre leaf. a) It is called middle leaf b) It is called master leaf c) Yes d) None of the listed

Last Answer : b) It is called master leaf

The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Description : The helix angle is very small about 20. The spring is open coiled spring. a) Yes b) It is closed coiled spring c) That small angle isn’t possible d) None of the listed

Last Answer : b) It is closed coiled spring

A knuckle joint can be used in valve mechanism of a reciprocating engine. a) Yes b) No c) Yes but there are stress probles d) No as it is very dangerous to use

Description : A knuckle joint can be used in valve mechanism of a reciprocating engine. a) Yes b) No c) Yes but there are stress probles d) No as it is very dangerous to use

Last Answer : a) Yes

Knuckle Joint can’t be used to connect two intersecting rods. a) Yes b) No, it can’t be used c) It can be used with some modificatios d) It is expensive and hence isn’t used

Description : Knuckle Joint can’t be used to connect two intersecting rods. a) Yes b) No, it can’t be used c) It can be used with some modificatios d) It is expensive and hence isn’t used

Last Answer : b) No, it can’t be used

The elastic stress strain behavior of rubber is A. Linear B. Nonlinear C. Plastic D. No fixed relationship

Description : The elastic stress strain behavior of rubber is A. Linear B. Nonlinear C. Plastic D. No fixed relationship

Last Answer : B. Nonlinear

Heating and cooling in welding is a. Even b. Non-even c. Cannot say d. None

Description : Heating and cooling in welding is a. Even b. Non-even c. Cannot say d. None

Last Answer : b. Non-even

Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined

Description : Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined

Last Answer : b) Electric arc welding

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

A spring is defined as a(an) ___ machine element. (A) plastic (B) elastic (C) special purpose (D) none of the above

Description : A spring is defined as a(an) ___ machine element. (A) plastic (B) elastic (C) special purpose (D) none of the above

Last Answer : (B) elastic

The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit

Description : The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit

Last Answer : (B) Within elastic limit

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant

A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact

A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (D) Where there is no lubricant

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

At ‘yield point’ of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become plastic C. even the plastic stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Description : At yield point' of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become ... stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Last Answer : the load has already exceeded the elastic limit and the material has become plastic

Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Description : Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Last Answer : d) All of the listed

When two Belleville sprigs are arranged in series, half deflection is obtained for same force. a) One fourth deflection b) Double deflection c) Four time deflection d) None of the listed

Description : When two Belleville sprigs are arranged in series, half deflection is obtained for same force. a) One fourth deflection b) Double deflection c) Four time deflection d) None of the listed

Last Answer : b) Double deflection

Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Description : Calculate the force acting on the each pin in flexible coupling if torque transmitted is 397N-m and PCD=120mm with number of pins 6. a) 1400.3N b) 1102.8N c) 1320.3N d) None of the listed

Last Answer : b) 1102.8N

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Which of the following are parts of knuckle joint. A. Eye B. Pin C.Fork D. All of the above

Description : Which of the following are parts of knuckle joint. A. Eye B. Pin C.Fork D. All of the above

Last Answer : D. All of the above

Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Description : Which of the following are important parts of knuckle joint? a) Eye b) Pin c) Fork d) Each of the mentioned

Last Answer : d) Each of the mentioned

Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Description : Resilience is defined as the property of material to absorb energy when deformed _________ and to release this energy when unloaded. a) Elastically b) Plastically c) Up to fracture point d) None of the listed

Last Answer : a) Elastically

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings create a lot of noise. (a) Yes (b) Depends on the application (c) They create very less noise (d) No reference frame for comparison is mentioned

Last Answer : (c) They create very less noise

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Description : Deep groove ball bearings creates a lot of noise. a) Yes b) They create very less noise c) Depends on the application d) No reference frame for comparison is mentioned

Last Answer : b) They create very less noise

Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Description : Bending stress in graduated length leaves are more than that in full length leaves. a) Yes b) No c) In some cases d) Can’t be stated

Last Answer : b) No

Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root

Description : The load shared by each spring is inversely proportional to the cross section of wire. a) Yes b) No, it is directly proportional c) It is proportional to its square d) It is proportional to its square root

Last Answer : b) No, it is directly proportional

Taper is made cotter and slot on both the side. A. Yes B. No

Description : Taper is made cotter and slot on both the side. A. Yes B. No

Last Answer : B. No

Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Last Answer : b) No, they are subjected to compressive forces only

Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No

Last Answer : b) No