Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No
Last Answer : b) No
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : Entire torque is transmitted by friction in the clamp coupling. a) True b) False
Last Answer : b) False
Description : Clamp coupling employ bolts. a) True b) False
Last Answer : a) True
Description : In case of clamp coupling, power is transmitted by means of, (A) Friction force (B) Shear resistance (C) Crushing resistance (D) None of the above
Last Answer : (A) Friction force
Description : The angular play bearing must be mounted without axial play. (a) Yes (b) Little tolerance is adjusted
Last Answer : (a) Yes
Description : The angular play bearing must be mounted without axial play. a) Yes b) Little tolerance is adjusted c) Little tolerance is necessary d) Can’t be stated
Last Answer : a) Yes
Description : Pitch of coil is defined as axial distance in compressed state of the coil. a) Yes b) It is measured in uncompressed state c) It is same in uncompressed or compressed state d) None of the listed
Last Answer : b) It is measured in uncompressed state
Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3
Last Answer : (b) 1 and 2
Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed
Last Answer : b) Radial
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Muff coupling is designed as a ......... A. Thick cylinder B. Thin cylinder C. Solid shaft D. Hollow shaft
Last Answer : D. Hollow shaft
Description : While designing a flange coupling, care is taken so that (A) Shaft is the weakest component (B) Bolts are the weakest component (C) Key is the weakest component (D) The flange is the weakest component
Last Answer : (C) Key is the weakest component
Description : In designing a flange coupling, the pitch circle diameter of bolts is taken as (where d = Diameter of the shaft) (A) 2 d (B) 3 d (C) 4 d (D) 5 d
Last Answer : (B) 3 d
Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial
Last Answer : c) Sliding, Radial
Description : In hydrodynamic bearing, when the shaft begins to rotate in clockwise direction, (A) The journal climbs to the right side of the bearing without metal to metal contact (B) The journal climbs to the left ... sinks down to the bottom of the bearing (D) The journal is at the center of the bearing
Last Answer : (A) The journal climbs to the right side of the bearing without metal to metal contact
Description : Feather key can be used to prevent axial motion between two elements. a) True b) False
Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity
Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity
Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load
Last Answer : A. Radial load
Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned
Last Answer : (c) both radial and axial loads
Description : A cotter joint is used to connect two __________ rods. A. Co-axial B. Perpendicular C. Parallel D. None of these
Last Answer : A. Co-axial
Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4
Last Answer : (c) 2 4 3 1
Description : Footstep bearing is an axial load bearing. a) True b) Thrust load c) Shear load d) None of the listed
Last Answer : b) Thrust load
Description : Taper rolling supports a) Axial loads b) Thrust loads c) Both axial and thrust loads d) None of the mentioned
Last Answer : c) Both axial and thrust loads
Description : Axial length of an unloaded helical compression spring is called (A) compressed length (B) solid length (C) free length (D) none of the above
Last Answer : (C) free length
Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above
Last Answer : (B) solid length
Description : The leaves of multi-leaf springs are subjected to (A) bending stress (B) shear stress (C) axial stress (D) all of the above
Last Answer : (A) bending stress
Description : When two concentric springs are made of same material, having same free length and compressed equally by axial load, then the load shared by each spring is proportional to (A) Spring index of each spring ... spring (C) Mean coil diameter of each spring (D) Square of wire diameter of each spring
Last Answer : (D) Square of wire diameter of each spring
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : The stiffness of spring is, (A) Deflection per unit of axial force (B) Force per unit cross-sectional area of spring (C) Ratio of mean coil diameter to wire diameter (D) Force required to produce unit deflection
Last Answer : (D) Force required to produce unit deflection
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : The axial deflection of spring for the small angle of θ is given by? a) 328PDɜN/Gd4 b) 8PDɜN/Gd4 c) 16PDɜN/Gd4 d) 8PD2N/Gdɜ
Last Answer : b) 8PDɜN/Gd4
Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above
Last Answer : c) Axial tensile or compressive
Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load
Last Answer : C. Axial tensile or compressive load
Description : Cotter joints is connected two ......... roads. A. Co - axial B. Parallel C. Perpendicular D. Inclined
Last Answer : A. Co - axial
Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned