Description : Parallel fillet welds are under (i) Shear stress (ii)Compressive stress (iii)Tensile stress (iv)None
Last Answer : (i) Shear stress
Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress
Last Answer : (iii) Tensile stress
Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None
Last Answer : (iv)None
Description : Parallel fillet welds are under Shear and bending stresses Compressive and torsion shear stresses Tensile and compressive stresses None
Last Answer : None
Description : The spokes of the flywheel are subjected to 1. direct shear stress 2. torsional shear stress 3. tensile stress 4. compressive stress
Last Answer : 3. tensile stress
Description : The rim of the flywheel is subjected to, 1. direct tensile stress and bending stress 2. torsional shear stress and bending stress 3. direct shear stress and bending stress 4. compressive stress and bending stress
Last Answer : 1. direct tensile stress and bending stress
Description : The spokes of the flywheel are subjected to, (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (C) Tensile stress
Description : When the helical torsion spring is subjected to torque, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (C) Bending stress
Description : When the helical compression spring is subjected to axial compressive force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Last Answer : (D) Torsional shear stress
Description : When the helical extension spring is subjected to axial tensile force, the type of stress induced in the spring wire is, (A) Tensile stress (B) Compressive stress (C) Bending stress (D) Torsional shear stress
Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Last Answer : (A) Direct shear stress
Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress
Description : A principal stress is a. Tensile or shear stress b. Compressive or shear stress c. Tensile or compressive stress d. None
Last Answer : c. Tensile or compressive stress
Description : A complementary shear stress is equal in magnitude and opposite in rotational tendency of an applied (a) Tensile stress (b) Compressive stress (c) Shear stress (d) None
Last Answer : (c) Shear stress
Description : A principal plane is a plane of (a) Zero tensile stress (b) Zero compressive stress (c) Zero shear stress (d) None
Last Answer : (c) Zero shear stress
Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength
Last Answer : (d) shear strength
Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength
Last Answer : (a) tensile strength
Description : Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) None of the listed
Last Answer : b) Tensile
Description : In the analysis, all the principal stresses are assumed as a. Shear stresses b. Compressive stresses c. Tensile stresses d. None
Last Answer : c. Tensile stresses
Description : Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None
Last Answer : a. Firstly All tensile
Description : The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress
Last Answer : (c) fluctuating stress
Description : If compressive yield stress and tensile yield stress are equivalent, then region of safety from maximum principal stress theory is of which shape? a) Rectangle b) Square c) Circle d) Ellipse
Last Answer : b) Square
Description : The principal strain due to σ1(tensile) and σ2 (Compressive ) stress is (a) Firstly (b)Secondly (c)Thirdly (d) None
Last Answer : (b)Secondly
Description : The compressive stress induced in a square key is, (A) Equal to shear stress (B) Four times of shear stress (C) Twice of shear stress (D) Half of shear stress
Last Answer : (C) Twice of shear stress
Description : Identify the principal stress (a) Shear stress (b) Bending stress (c) Compressive stress (d) None
Last Answer : (c) Compressive stress
Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None
Last Answer : c. Principal tensile stress
Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these
Last Answer : c) Shear stress
Description : The rim of the flywheel is subjected to, (A) Direct tensile stress and bending stress (B) Torsional shear stress and bending stress (C) Direct shear stress and bending stress
Last Answer : (A) Direct tensile stress and bending stress
Description : What is the value of shear stress acting on a plane of circular bar which is subjected to axial tensile load of 100 kN? (Diamet a. 58.73 Mpa b. 40.23 Mpa c. 39.60 Mpa d. Insufficient data
Last Answer : c. 39.60 Mpa
Description : While calculating bending stress in the following welded joints which of the welds moment of inertia can be neglected? a) 1 b) None of the listed c) Both 1 & 3 d) Both 2 & 4
Last Answer : b) None of the listed
Description : A bracket is shown welded to a vertical column by means of two fillet welds. The bending stress induced in the welds can be given by a) My/I b) 2My/I c) My/2I d) None of the listed
Last Answer : a) My/I
Description : Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None
Last Answer : (ii) Lap joint
Description : Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None
Last Answer : (i) Butt joint
Description : The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None
Last Answer : (ii) Butt welded joint
Description : By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None
Last Answer : (i) Fillet welded joint
Description : Out of the followings, which welded joint is more stronger (i) Butt joint (ii) Lap joint (iii)Screwed joint
Description : Why are butt welded joints longitudinal joints ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements iv. None
Last Answer : i. High strength requirements
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress
Last Answer : B Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress
Last Answer : (B) Bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress
Last Answer : b) bending stress
Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned
Last Answer : b) tensile stress
Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress
Description : __________ stress cannot be sustained by a fluid in equilibrium. (A) Shear (B) Tensile (C) Compressive
Last Answer : Option A
Description : A fluid in equilibrium can't sustain (A) Tensile stress (B) Compressive stress (C) Shear stress (D) Bending stress
Last Answer : Answer: Option C
Description : The main reason for providing number of reinforcing bars at a support in a simply supported beam is to resist in that zone (A) Compressive stress (B) Shear stress (C) Bond stress (D) Tensile stress
Description : Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these
Last Answer : (a) Compressive stress.
Description : Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.
Last Answer : (c) Tensile, compressive and shear stresses.