When two plates butt together and are riveted with two cover plates with two rows of rivets, the joint is known as (A) Lap joint (B) Butt joint (C) Single riveted single cover butt joint (D) Double riveted double cover butt joint

When two plates butt together and are riveted with two cover plates with two rows of rivets, the
joint is known as
(A) Lap joint
(B) Butt joint
(C) Single riveted single cover butt joint
(D) Double riveted double cover butt joint
by

1 Answer

Answer :

(D) Double riveted double cover butt joint
by

Related questions

Failure of riveted joints is due to (A) Tearing of the plates between the rivet hole and the edge of the plate (B) Tearing of plates between rivets (C) Shearing of rivets (D) All the above

Description : Failure of riveted joints is due to  (A) Tearing of the plates between the rivet hole and the edge of the plate  (B) Tearing of plates between rivets  (C) Shearing of rivets  (D) All the above 

Last Answer : (D) All the above 

The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight

Description : The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight

Last Answer : Option A

The type of butt joints in common use, is: (A) Single inverted V-butt joint (B) Double V-butt joint (C) Double U-butt joint (D) Single V-butt joint

Description : The type of butt joints in common use, is: (A) Single inverted V-butt joint (B) Double V-butt joint (C) Double U-butt joint (D) Single V-butt joint

Last Answer : (A) Single inverted V-butt joint

Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year showing the cost at that time relative to a certain base year (C) Turnover ratio of a chemical plant is the ratio of gross annual sales to the fixed capital investment (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Description : Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year ... butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Last Answer : (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

The distance between the centres of adjacent rivets in the same row, is called (A) Pitch (B) Lap (C) Gauge (D) Staggered pitch

Description : The distance between the centres of adjacent rivets in the same row, is called (A) Pitch (B) Lap (C) Gauge (D) Staggered pitch

Last Answer : (A) Pitch

If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called (A) Chain riveting (B) Zig-zag riveting (C) Diamond riveting (D) None of these

Description : If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called (A) Chain riveting (B) Zig-zag riveting (C) Diamond riveting (D) None of these

Last Answer : (C) Diamond riveting

Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Which welded joint used in the circumferential joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (ii) Lap joint

Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Description : Welded joint used in the longitudinal joint of a cylindrical pressure vessel is (i) Butt joint (ii) Lap joint (iii)Screwed joint (iv) None

Last Answer : (i) Butt joint

Out of the followings, which welded joint is more stronger (i) Butt joint (ii) Lap joint (iii)Screwed joint

Description : Out of the followings, which welded joint is more stronger (i) Butt joint (ii) Lap joint (iii)Screwed joint

Last Answer : (i) Butt joint

As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint. (A) Butt (B) Lap (C) Welded (D) None of these

Description : As per the Indian boiler regulation (IBR), the type of joint preferred for the circumferential joint is the __________ joint. (A) Butt (B) Lap (C) Welded (D) None of these

Last Answer : (B) Lap

Which of the following is preferred for riveting? (A) Lap joint (B) Butt joint (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : Which of the following is preferred for riveting? (A) Lap joint (B) Butt joint (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (B) Butt joint

The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (ii) Butt welded joint

By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : By overlapping the plates, which type of welded joint is made (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (i) Fillet welded joint

Steel pipe are (A) Suitable for withstanding high internal pressure (B) Connected by riveted or welded joints (C) Generally laid underground and no expansion joint is required (D) Likely to last 100 years under ordinary conditions

Description : Steel pipe are  (A) Suitable for withstanding high internal pressure  (B) Connected by riveted or welded joints  (C) Generally laid underground and no expansion joint is required  (D) Likely to last 100 years under ordinary conditions 

Last Answer : (D) Likely to last 100 years under ordinary conditions 

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod

Description : Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod

Last Answer : (B) Boiler plates, rivets etc.

The minimum pitch of rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.75 x d d) 2.5 x d*

Description : The minimum pitch of rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.75 x d d) 2.5 x d*

Last Answer : d) 2.5 x d*

The minimum edge distance for rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.5 x d* d) 2.5 x d

Description : The minimum edge distance for rivets of diameter ‘d’ in steel plates shall be a) 2 x d b) 3 x d c) 1.5 x d* d) 2.5 x d

Last Answer : c) 1.5 x d*

Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None

Description : Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None

Last Answer : c. No change in tension strength

The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None

Description : The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None

Last Answer : a. Greater

Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Description : Efficiency of a welded joint with respect to a riveted joint is a. Smaller b. Equal c. Greater

Last Answer : c. Greater

The advantage of a welded joint over a riveted joint is (i) Introduce residual stresses (ii) Requires highly skilled labor and supervision (iii) Lighter in weight (iv) None

Description : The advantage of a welded joint over a riveted joint is (i) Introduce residual stresses (ii) Requires highly skilled labor and supervision (iii) Lighter in weight (iv) None

Last Answer : (iii) Lighter in weight

The objective of caulking in a riveted joint is to make the joint (A) Free from corrosion (B) Stronger in tension (C) Free from stress (D) Leak-proof

Description : The objective of caulking in a riveted joint is to make the joint (A) Free from corrosion (B) Stronger in tension (C) Free from stress (D) Leak-proof

Last Answer : (D) Leak-proof

. Lap joints are preferred over butt joints in soldering/brazing, because these joints are (A) Weaker in tension but stronger in shear (B) Weaker in shear but stronger in tension (C) Stronger in both shear and tension (D) The lap joints are easily made

Description : . Lap joints are preferred over butt joints in soldering/brazing, because these joints are (A) Weaker in tension but stronger in shear (B) Weaker in shear but stronger in tension (C) Stronger in both shear and tension (D) The lap joints are easily made

Last Answer : r: Option D

The type of joint commonly used at the junction of a principal rafter and tie beam in timber trusses is (A) Mortise and tenon joint (B) Oblique mortise and tenon joint (C) Butt joint (D) Mitred joint

Description : The type of joint commonly used at the junction of a principal rafter and tie beam in timber trusses is (A) Mortise and tenon joint (B) Oblique mortise and tenon joint (C) Butt joint (D) Mitred joint

Last Answer : Answer: Option B

When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the calculated stresses are known as (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Description : When the distance between centers of two adjacent rivets connecting the members subjected to either compression or tension exceeds the maximum pitch, then the additional rivets which are not subjected to the ... (a) Packing rivets (b) Long-grip rivets (c) Tacking rivets (d) Auxiliary rivets

Last Answer : (c) Tacking rivets

The minimum number of rivets for the connection of a gusset plate, is (A) 1 (B) 2 (C) 3 (D) 4

Description : The minimum number of rivets for the connection of a gusset plate, is (A) 1 (B) 2 (C) 3 (D) 4

Last Answer : (B) 2

A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Last Answer : (a) butt weld

The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (b) Throat of weld

Joint which does not fall under lap joint category (i)Transverse fillet (ii) Parallel fillet (iii) Circular fillet (iv) None

Description : Joint which does not fall under lap joint category (i)Transverse fillet (ii) Parallel fillet (iii) Circular fillet (iv) None

Last Answer : (iv) None

In lap winding, the number of brushes is always (a) double the number of poles (b) same as the number of poles (c) half the number of poles (d) two

Description : In lap winding, the number of brushes is always (a) double the number of poles (b) same as the number of poles (c) half the number of poles (d) two

Last Answer : Ans: b

Drawing of number of copies of the same image in rows and columns acrossthe interface window so that they cover the entire window is called a.Roaming b.Panning c.Zooming d.Tiling

Description : Drawing of number of copies of the same image in rows and columns acrossthe interface window so that they cover the entire window is called a.Roaming b.Panning c.Zooming d.Tiling

Last Answer : d.Tiling

If a boy rows 8 km downstream in 6 hours and 4 km upstream in 4 hours then how long will he take to cover 16 km in stationary (still) water? A) 8 B) 14 C) 22 D) 16

Description : If a boy rows 8 km downstream in 6 hours and 4 km upstream in 4 hours then how long will he take to cover 16 km in stationary (still) water? A) 8 B) 14 C) 22 D) 16 

Last Answer : Answer: B Explanation: Distance covered in downstream = 8 km Time taken in downstream = 6 hours. Rate of downstream = 8/6=4/3 km/hr Distance covered in upstream = 4 km Time taken in upstream = 4hours. ... 3+1) = 7/6km/hr Time Taken to cover 16 km in still water = 16*6/7=14hrs (approximately)

Where can I find these briolette jewel rivets?

Description : Where can I find these briolette jewel rivets?

Last Answer : Have you tried Rio Gems/Findings?

How do you remove rivets?

Description : How do you remove rivets?

Last Answer : Find a drill bit a little smaller than the rivets. Drill the rivet out. It should come right out as soon as it gets through the middle of the rivet. The original hole is left as it was. This is ... back together. You can put the same sized rivets back in the holes if you have a rivet gun and rivets

How many rivets in the golden gate bridge?

Description : How many rivets in the golden gate bridge?

Last Answer : 600,000 in each of the two towers

Inspection of welded joints with respect to riveted joints is a. Difficult b. Easier c. Cannot say d. None

Description : Inspection of welded joints with respect to riveted joints is a. Difficult b. Easier c. Cannot say d. None

Last Answer : a. Difficult

Appearance of welded structures with respect to riveted structures is a. Smooth b. Rough c. Same d. None

Description : Appearance of welded structures with respect to riveted structures is a. Smooth b. Rough c. Same d. None

Last Answer : a. Smooth

Welded structures with to riveted structures for a certain load are a. Heavier b. Lighter c. Same weight d. None

Description : Welded structures with to riveted structures for a certain load are a. Heavier b. Lighter c. Same weight d. None

Last Answer : b. Lighter

The welded structure with respect to riveted structure is a. Heavier b. Lighter c. Same d. None

Description : The welded structure with respect to riveted structure is a. Heavier b. Lighter c. Same d. None

Last Answer : b. Lighter

Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%? (A) Small punches, broaches reamers and springs (B) Cutlery, screws, rivets and files (C) Mandrels, twist drills, small lathe tools and razors (D) Forgings like can shaft, structural steel plate, threading dies and drawing dies

Description : Which of the following are made out of the carbon steel having carbon content of 0.9 to 1%? (A) Small punches, broaches reamers and springs (B) Cutlery, screws, rivets and files (C) ... lathe tools and razors (D) Forgings like can shaft, structural steel plate, threading dies and drawing dies

Last Answer : (A) Small punches, broaches reamers and springs

In flange splices when the number of hammer and hand loose rivets is 30% or more of the total rivets on any side of the splice location, a) Need no be renewed b) wait for 100% loose rivets c) all the rivets should be renewed.* d) None of the above

Description : In flange splices when the number of hammer and hand loose rivets is 30% or more of the total rivets on any side of the splice location, a) Need no be renewed b) wait for 100% loose rivets c) all the rivets should be renewed.* d) None of the above

Last Answer : c) all the rivets should be renewed.*

Renewal of slack rivets should be taken up in steel girder bridges: a) All rivets which are hand loose or which have lost 50% of their head by corrosion. b) All hammer loose rivets where corrosion has set in between the head and the plate. c) In end stiffeners when the percentage of hammer loose rivets is >30% d) All the above*

Description : Renewal of slack rivets should be taken up in steel girder bridges: a) All rivets which are hand loose or which have lost 50% of their head by corrosion. b) All hammer loose rivets where corrosion has set ... . c) In end stiffeners when the percentage of hammer loose rivets is >30% d) All the above*

Last Answer : d) All the above*

The growing of wheat and mustard simultaneously together in rows, is called— (A) Multiple cropping (B) Relay cropping (C) Mixed cropping (D) Inter cropping

Description : The growing of wheat and mustard simultaneously together in rows, is called— (A) Multiple cropping (B) Relay cropping (C) Mixed cropping (D) Inter cropping

Last Answer : (D) Inter cropping

Pick up the correct statement from the following: (A) In a king post truss, principal rafter and tie beams are jointed together with a bridle joint (B) Joint between the principal rafter and the king post is made by making tenon and mortise respectively (C) Joint between strut and king post, is generally of mortise and tenon type (D) All the abov

Description : Pick up the correct statement from the following: (A) In a king post truss, principal rafter and tie beams are jointed together with a bridle joint (B) Joint between the principal rafter and the king ... ) Joint between strut and king post, is generally of mortise and tenon type (D) All the above

Last Answer : Answer: Option D

In brick masonry the bond produced by laying alternate headers and stretchers in each course is known as (A) English bond (B) Double Flemish bond (C) Zigzag bond (D) Single Flemish bond

Description : In brick masonry the bond produced by laying alternate headers and stretchers in each course is known as (A) English bond (B) Double Flemish bond (C) Zigzag bond (D) Single Flemish bond

Last Answer : Answer: Option B

Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Last Answer : (i)0.707 tl

When two companies, who are usually rivals, come together to do business on a worldwide basis, this partnership is known as a 1. joint venture 2. strategic alliance 3. multinational venture 4. joint licensing 5. none of these

Description : When two companies, who are usually rivals, come together to do business on a worldwide basis, this partnership is known as a 1. joint venture 2. strategic alliance 3. multinational venture 4. joint licensing 5. none of these

Last Answer : strategic alliance

When two companies, who are usually rivals, come together to do business on a worldwide basis, this partnership is known as a A)joint venture B)strategic alliance C)multinational venture D)joint licensing

Description : When two companies, who are usually rivals, come together to do business on a worldwide basis, this partnership is known as a A)joint venture B)strategic alliance C)multinational venture D)joint licensing

Last Answer : B)strategic alliance