Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined
Last Answer : b) 45
Description : If the centre distance of the mating gears having involute teeth is varied within limits, the velocity ratio (A) Increases (B) Decreases (C) Remains unchanged (D) None of these
Last Answer : (C) Remains unchanged
Description : In a general two dimensional stress system, planes of maximum shear stress are inclined at ___ with principal planes. a. 90 degree b. 180 degree c. 45 degree d. 60 degree
Last Answer : c. 45 degree
Description : The angle of V-welded joint in a pressure vessel 30 to 45 0 40 to 55 0 55 to 70 0 None
Last Answer : 55 to 70 0
Description : Splines are keys. a) True b) False
Last Answer : a) True
Description : Splines are commonly used in (A) Machine tool gear box (B) Automobile gear box (C) Hoist and crane gear box (D) Bicycle
Last Answer : (B) Automobile gear box
Description : Splines are used if, (A) The power to be transmitted is high (B) The torque to be transmitted is high (C) The speed is high (D) There is relative motion between shaft and hub
Last Answer : (D) There is relative motion between shaft and hub
Description : All the principal stresses are at an angle of (a) 45 0 (b) 60 0 (c) 75 0 (d) None
Last Answer : (d) None
Description : The angle between a principal plane and a plane of maximum shear is a. 30 0 b. 60 0 c. 90 0 d. None
Last Answer : d. None
Description : When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined
Last Answer : 1. Accelerated
Description : When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined
Last Answer : a) Accelerated
Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined
Last Answer : (a) Yes
Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined
Last Answer : b) Journal radius is kept smaller
Description : Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined
Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined
Last Answer : a) Yes
Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined
Last Answer : b) Double force
Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined
Last Answer : b) No it is flexible
Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined
Last Answer : b) No, they are subjected to compressive forces only
Description : For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material
Last Answer : a) Increase
Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None
Last Answer : c. 45 0
Description : The angle between a principal plane and a plane of maximum shear is a. 15 0 b. 45 0 c. 75 0 d. None
Last Answer : b. 45 0
Description : All the maximum shear stresses are at an angle of (a)45 0 (b) 90 0 (c) 135 0 (d) None
Last Answer : (b) 90 0
Description : All the principal strains are at an angle of (a) 45 0 (b) 90 0 (c) 135 0 (d) None
Description : All the principal stresses are at an angle of (a)90 0 (b) 45 0 (c) 135 0 (d) None
Last Answer : (a)90 0
Description : Principal planes are mutually inclined at a. 45 degree b. 60 degree c. 90 degree d. 180 degree
Last Answer : c. 90 degree
Description : Where the complaint alleges a defect in the goods which cannot be determined without proper analysis or test of the goods, the sample of goods forwarded to appropriate laboratory for laboratory test. Such types of case finding report within ______days a) 30 b) 40 c) 45 d) 60
Last Answer : c) 45
Description : If load on the engine is constant, the mean speed will be constant and ___ will not operate. a) Flywheel b) Governor c) Both flywheel and governor d) None of the mentioned
Last Answer : b) Governor
Description : A spring index from ___ is considered as best for manufacturing considerations. (A) 4 to 12 (B) 12 to 20 (C) 20 to 28 (D) 28 to 36
Last Answer : (A) 4 to 12
Description : The spring index indicates the relative sharpness of the ___ of the coil. (A) length (B) curvature (C) thickness (D) none of the above
Last Answer : (B) curvature
Description : A spring is defined as a(an) ___ machine element. (A) plastic (B) elastic (C) special purpose (D) none of the above
Last Answer : (B) elastic
Description : The direction of projection for the range of a projectile to be maximum on an inclined plane having angle of inclination 30? to the horizontal, whould be a.45? with horizontal b.30? with vertical c.30? with horizontal d.60? with inclined plane e.45? with inclined plane
Last Answer : b. 30? with vertical
Description : A body of weight 100 kg is placed on a horizontal plane. A horizontal force of 30 kg is applied and the block is just on the point of motion. The angle of friction is a.About 16? b.30? c.45? d.60? e.None of the above
Last Answer : a. About 16?
Description : A gun fires shell with a muzzle velocity of 600 m/sec. The angle of inclination of the gun so that the shell hits a target at a distance of 32 km at level 100 m higher than the gun would be approximately? a.60? b.45? c.30? d.15? e.Either of (A) and (C)
Last Answer : e. Either of (A) and (C)
Description : The angle at which the wave must be transmitted in air media if the angle of reflection is 45 degree is a) 45 b) 30 c) 60 d) 90
Last Answer : a) 45
Description : The critical angle for two media of refractive indices of medium 1 and 2 given by 2 and 1 respectively is a) 0 b) 30 c) 45 d) 60
Last Answer : b) 30
Description : Find the acceptance angle of a material which has a numerical aperture of 0.707 in air. a) 30 b) 60 c) 45 d) 90
Description : Find the angle at which the torque is minimum. a) 30 b) 45 c) 60 d) 90
Last Answer : d) 90
Description : Find the angle at which the potential due a dipole is measured, when the distance from one charge is 12cm and that due to other is 11cm, separated to each other by a distance of 2cm. a) 15 b) 30 c) 45 d) 60
Last Answer : d) 60
Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100
Last Answer : (a) 43 to 45
Description : Flooding nozzle have spray angle a) 100-150 b) 90-100 c) 60-95 d) 30-45
Last Answer : a) 100-150
Description : When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined
Last Answer : b) Split flywheel
Description : If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined
Last Answer : a) Hydrostatic
Description : If spring index=2.5, what can be concluded about stresses in the wire? a) They are high b) They are negligible c) They are moderate d) Cannot be determined
Last Answer : a) They are high
Description : Among gas and electric arc welding, which has the higher rate of heating? a) Gas welding b) Electric arc welding c) Gas welding and electric arc welding have equal rate of heating d) Cannot be determined
Last Answer : b) Electric arc welding
Description : Which threads have greater resistance to unscrewing? a) Coarse b) Fine c) They have equal resistance d) Cannot be determined
Last Answer : b) Fine
Description : Efficiency of the screw _______ with increase of coefficient of friction. a) decreases b) increases c) has no effect d) cannot be determined
Last Answer : a) decreases
Description : Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined
Last Answer : a) Reduce the stress concentration
Description : Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above
Last Answer : c. Principal stress
Description : All welding processes require pressure along with heat. a) Yes b) No, fusion doesn’t require c) Can’t be stated d) None of the listed
Last Answer : b) No, fusion doesn’t require