For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor will______ a) Increase b) Decrease c) Remains constant d) Can’t be determined. Varies from material to material

For an elliptical hole on a flat plate, if width of the hole in direction of the load decrease, Stress Concentration Factor

will______

a) Increase

b) Decrease

c) Remains constant

d) Can’t be determined. Varies from material to material
by

1 Answer

Answer :

a) Increase
by

Related questions

If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Description : If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress concentration factor is? a) 2 b) 3 c) 4 d) 1

Last Answer : b) 3

Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Description : Use of multiple notches in a V shaped flat plate will a) Reduce the stress concentration b) Increase the stress concentration c) No effect d) Cannot be determined

Last Answer : a) Reduce the stress concentration

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ 1. Accelerated 2. Decelerated 3. Constant velocity 4. Can’t be determined

Last Answer : 1. Accelerated

When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined

Description : When the driving torque is more than load torque, flywheel is ______ a) Accelerated b) Decelerated c) Constant velocity d) Can’t be determined

Last Answer : a) Accelerated

In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. normal stress varies linearly in the material c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Description : In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. ... c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Last Answer : c. elastic constants are same in all the directions

The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Description : The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Last Answer : (B) x0.8

A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole? (1) Increase (2) Decrease (3) Remain constant (4) Will increase first and then decrease

Description : A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole? (1) Increase (2) Decrease (3) Remain constant (4) Will increase first and then decrease

Last Answer : (1) Increase Explanation: Assuming the disc is uniform and isotropic (the same in different directions), the hole will expand in the same ratio as the metal. It is because the thermal expansion equation ... is made out of metal. And if the circumference of the hole expands, so does the diameter.

In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty

Description : In hydrodynamic lubrication, film thickness remains unaffected by change in speeds. a) True b) Increase with increase in speed c) Decrease with increase in speed d) Disappear as the speed tends to infinty

Last Answer : b) Increase with increase in speed

Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C

Last Answer : (A) (4C - 1/4C - 4) + 0.615/C

For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69

Last Answer : b) 0.87

For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Description : For a helical torsion sprig, the stress concentration factor at inner fibre is? Give spring index=5. a) 1.005 b) 1.175 c) 1.223 d) 1.545

Last Answer : b) 1.175

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Last Answer : b) False

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Last Answer : D. All of the above

Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Description : Which of the following reduces the stress concentration? a) Use of multiple notches b) Drilling additional holes c) Removal of undesired material d) Each of the mentioned

Last Answer : d) Each of the mentioned

Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug out whose size is kept equal to the size of the test plate (C) Bottom level of the hole dug at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Description : Pick up the correct statement applicable to plate load test (A) Width of the test pit for plate load test is made five times the width of the plate (B) At the centre of the test pit, a hole is dug ... at the centre of the test pit, is kept at the level of the actual formation (D) All the above

Last Answer : Answer: Option D

In an oil-lubricated journal bearing, coefficient of friction between the journal and the bearing. [IES-1995] (a) Remains constant at all speeds. (b) is minimum at zero speed and increases monotonically with increase in speed. (c) is maximum at zero speed and decreases monotonically with increase in speed. (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Description : In an oil-lubricated journal bearing, coefficient of friction between the journal and the bearing. [IES-1995] (a) Remains constant at all speeds. (b) is minimum at zero speed and increases ... speed. (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Last Answer : (d) becomes minimum at an optimum speed and then increases with further increase in speed.

Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of theoretical plate calculation for distillation column (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Description : Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of ... (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Last Answer : (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column

The rated life of a bearing varies (a) directly as load (b) inversely as the square of the load (c) inversely as the cube of the load

Description : The rated life of a bearing varies (a) directly as load (b) inversely as the square of the load (c) inversely as the cube of the load

Last Answer : (c) inversely as the cube of the load

The rated life of a bearing varies A. Directly as load B. Inversely as square of load C. Inversely as cube of load D. Inversely as fourth power of load

Description : The rated life of a bearing varies A. Directly as load B. Inversely as square of load C. Inversely as cube of load D. Inversely as fourth power of load

Last Answer : C. Inversely as cube of load

The rated life of a bearing varies (A) Directly as load (B) Inversely as square of load (C) Inversely as cube of load (D) Inversely as fourth power of load

Description : The rated life of a bearing varies (A) Directly as load (B) Inversely as square of load (C) Inversely as cube of load (D) Inversely as fourth power of load

Last Answer : (C) Inversely as cube of load

A copper plate has a circular hole cut in it. If the plate is heated to a higher temperature, the diameter of the hole (a) Becomes smaller (b) Increases (c) Remains constant (d) Increases but the total area of the plate remains constant

Description : A copper plate has a circular hole cut in it. If the plate is heated to a higher temperature, the diameter of the hole (a) Becomes smaller (b) Increases (c) Remains constant (d) Increases but the total area of the plate remains constant

Last Answer : Ans:(b)

In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder (C) Velocity profile varies hyperbolically and the shear stress remains constant over the cross-section (D) Average flow occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)

Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder

Shear stress in a fluid flowing in a round pipe (A) Varies parabolically across the cross-section(B) Remains constant over the cross-section(C) Is zero at the centre and varies linearly with the radius(D) Is zero at the wall and increases linearly to the centre

Description : Shear stress in a fluid flowing in a round pipe (A) Varies parabolically across the cross-section (B) Remains constant over the cross-section (C) Is zero at the centre and varies linearly with the radius (D) Is zero at the wall and increases linearly to the centre

Last Answer : (C) Is zero at the centre and varies linearly with the radius

A flywheel is used 1. to limit the fluctuation of speed during each cycle 2. to control the mean speed of the engine 3. to maintain a constant speed 4. to come into action when the speed varies

Description : A flywheel is used 1. to limit the fluctuation of speed during each cycle 2. to control the mean speed of the engine 3. to maintain a constant speed 4. to come into action when the speed varies

Last Answer : 1. to limit the fluctuation of speed during each cycle

A flywheel is used, (A) To limit the fluctuations of speed during each cycle (B) To control the mean speed of the engine (C) To maintain a constant speed (D) To come into action when the speed varies

Description : A flywheel is used, (A) To limit the fluctuations of speed during each cycle (B) To control the mean speed of the engine (C) To maintain a constant speed (D) To come into action when the speed varies

Last Answer : (A) To limit the fluctuations of speed during each cycle

If the clearance of a drug remains constant, doubling the dose rate will increase the steady-state plasma drug concentration by a factor of: A. × 3 B. × 2 C. × 1.5 D. × 1.3

Description : If the clearance of a drug remains constant, doubling the dose rate will increase the steady-state plasma drug concentration by a factor of: A. × 3 B. × 2 C. × 1.5 D. × 1.3

Last Answer : B. × 2

If the clearance of a drug remains constant, doubling the dose rate will increase the steady-state plasma drug concentration by a factor of: A. × 3 B. × 2 C. × 1.5 D. × 1.3

Description : If the clearance of a drug remains constant, doubling the dose rate will increase the steady-state plasma drug concentration by a factor of: A. × 3 B. × 2 C. × 1.5 D. × 1.3

Last Answer : B. × 2

When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Description : When comes down to stress reduction, which one is preferred? a) Solid flywheel b) Split flywheel c) Both have equal stresses d) Cannot be determined

Last Answer : b) Split flywheel

Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above

Description : Which of the following stresses can be determined using Mohr's circle method? a. Torsional stress b. Bending stress c. Principal stress d. All of the above

Last Answer : c. Principal stress

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Description : The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Last Answer : (d) viscosity, speed and bearing pressure.

The disintegration rate of a radioactive element (A) Progressively increases (B) Progressively decreases (C) Remains constant throughout (D) May increase or decrease depending on the material

Description : The disintegration rate of a radioactive element (A) Progressively increases (B) Progressively decreases (C) Remains constant throughout (D) May increase or decrease depending on the material

Last Answer : (B) Progressively decreases

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. Calculate the initial pre load required to close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can’t be determined

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... close the nip. (a) 4332.2N (b) 4674.1N (c) 4985.4N (d) Can't be determined

Last Answer : (b) 4674.1N

In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Description : In sliding contact bearings, a positive pressure can be built up and a load supported by a fluid only by the use of a: [IES-2005] (a) Diverging film (b) Converging-diverging film (c) Converging film (d) Flat film

Last Answer : (c) Converging film

If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Description : If we exclude the cost factor, which bearing is preferred? a) Hydrostatic b) Hydrodynamic c) Both are equally preferred d) Cannot be determined

Last Answer : a) Hydrostatic

There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Description : There is a problem of alignment in deep groove ball bearings. (a) Yes (b) No, it is self-aligning (c) It aligns itself only in some particular cases (d) Can’t be determined

Last Answer : (a) Yes

A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Description : A clearance bearing is design accurately to keep the radius of journal and bearing equal. a) Journal radius is kept larger b) Journal radius is kept smaller c) True d) Can’t be determined

Last Answer : b) Journal radius is kept smaller

Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined

Description : Partial bearing is preferred over journal bearing. a) True b) No c) More friction losses d) Can’t be determined

Last Answer : a) True

There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Description : There is problem of alignment in deep groove ball bearings. a) Yes b) No, it is self-aligning c) It aligns itself only in some particular cases d) Can’t be determined

Last Answer : a) Yes

When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Description : When two Belleville springs are in parallel, half force is obtained for a given deflection. a) Half force b) Double force c) Same force d) Can’t be determined

Last Answer : b) Double force

Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. a) Yes b) No it is flexible c) It is of moderate rigidity d) Rigidity can’t be determined

Last Answer : b) No it is flexible

Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Description : Set screws are subjected to tensile forces only. a) Yes b) No, they are subjected to compressive forces only c) Both compressive and tensile d) Can’t be determined

Last Answer : b) No, they are subjected to compressive forces only

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Description : Involute splines have stub teeth with a pressure angle of ___ a) 30 b) 45 c) 60 d) Can’t be determined

Last Answer : b) 45

Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the journal. (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In equilibrium position, the journal inside a journal bearing remains floating on the oil film. [IES-1995] Reason (R): In a journal bearing, the load on the bearing is perpendicular to the axis of the ... explanation of A (c) A is true but R is false (d) A is false but R is true

Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A

A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary? [IES-2008] (a) Remains unchanged (b) Gets doubled (c) Gets reduced to one-fourth of original value (d) Gets reduced to half of original value

Description : A journal bearing with hydrodynamic lubrication is running steadily with a certain amount of minimum film thickness. When the load and speed are doubled, how does the minimum film thickness vary? [IES-2008 ... Gets reduced to one-fourth of original value (d) Gets reduced to half of original value

Last Answer : (a) Remains unchanged