List the types of power amplifier.

List the types of power amplifier.
by

1 Answer

Answer :

Types of Power amplifier:

1) Class A power amplifier

2) Class B power amplifier

3) Class AB power amplifier

4) Class C power amplifier
by

Related questions

List applications of power amplifier.

Description : List applications of power amplifier.

Last Answer : Below are the applications of power amplifiers across different sectors: 1.Consumer Electronics: Audio power amplifiers are used in almost all consumer electronic devices ranging from microwave ovens, ... data transfer rates and usability. They are also used in satellite communication equipment.

State and explain the working principle of FET amplifier and list its applications.

Description : State and explain the working principle of FET amplifier and list its applications.

Last Answer : Operation of FET amplifier: When small a.c. signal is applied to the gate, it produces variation in the gate to source voltage. This results in variation in the drain current. As ... input voltage.  Application: Buffer amplifier Low noise amplifier Cascade amplifier Chopper amplifier

State the need and types of amplifier coupling.

Description : State the need and types of amplifier coupling. 

Last Answer : Need of amplifier coupling: 1.When ever large amplifier with very good impedance matching is required, a signal stage amplifier circuit will not able to amplify the signal to a large extent. 2 ... 2.Transformer coupled amplifier 3.Direct coupled amplifier 4. Inductance (LC) coupling

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Last Answer : Parameter Class A Class B 

Sketch the single tuned amplifier.

Description : Sketch the single tuned amplifier.

Last Answer : single tuned amplifier

Draw the circuit of single tuned amplifier and state its operating principle.

Description : Draw the circuit of single tuned amplifier and state its operating principle.

Last Answer : Operating Principle: The working of tuned voltage amplifier may be understood by considering a radio frequency signal, to be amplified applied at the input of the amplifier. The resonant frequency ... will be amplified. And all the other frequencies will be rejected by the tuned circuit. 

Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Description : Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Last Answer : Diagram of complementary symmetry Class B push-pull amplifier: Working: The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input ... of class B, this circuit is termed as Complementary symmetry push pull class B amplifier.

Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Description : Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Last Answer : Advantages: 1. It has a wide frequency response. 2. For coupling the resistor and the capacitor are used and which are not expensive so the cost is low. 3. The circuit is very ... a wide frequency band. 5. It is high fidelity amplifier. 6. It provides less frequency distortion.

Draw the frequency response of DC amplifier. Comment on it.

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

Name two types of BJT &draw their symbols.

Description : Name two types of BJT &draw their symbols. 

Last Answer : Two types of BJT: * NPN * PNP 

List the types of coupling used in BJT amplifier.

Description : List the types of coupling used in BJT amplifier. 

Last Answer : Types of coupling used in BJT amplifier: i. Resistance capacitance (RC)coupling ii. Impedance coupling iii. Transformer coupling iv. Direct coupling

State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type.

Description : State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type. 

Last Answer : Need of multistage amplifier: The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, ... use more than one stage of amplification. Such an amplifier is called a MULTISTAGE AMPLIFIER .

Explain the operating principle of PNP transistor.

Description : Explain the operating principle of PNP transistor. 

Last Answer : The circuit connection of PNP transistor with supply voltages is as shown above. The emitter-base junction is connected as forward bias. Due to this the emitter pushes the holes from the P ... by the collector. This develops the collector current IC. This is how a PNP transistor operates. 

Define intrinsic standoff ratio.

Description : Define intrinsic standoff ratio.

Last Answer : It is defined as the ratio of the RB1 (base resistance 1) to the inter-base resistance RBB. 

State 2 advantages of JFET over BJT.

Description : State 2 advantages of JFET over BJT.

Last Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

Which type of MOSFET is called Normally ON MOSFET”? Why?

Description : Which type of MOSFET is called Normally ON MOSFET”? Why? 

Last Answer : DMOSFET is called Normally ON MOSFET. In DMOSFET already channel is present and at Vgs = 0v, drain current Id=Idss i.e. drain to source saturation current is flowing. 

Define gain and bandwidth.

Description : Define gain and bandwidth. 

Last Answer : Gain: It is the ratio of output quantity to the input quantity. Bandwidth: It is defined as the range (band) of frequency over which the gain is constant.  (Or) It is the range of frequency over which the gain is greater than 70.7% of the maximum gain possible

State any four applications of transistor.

Description : State any four applications of transistor.

Last Answer : Amplifier

Draw the characteristics of UJT and state its working principle.

Description : Draw the characteristics of UJT and state its working principle.

Last Answer : The characteristics of Unijunction Transistor (UJT) can be explained by three parameters: * Cutoff Region * Negative Resistance Region * Saturation Region Cutoff Region : The ... in its ON position. The emitter voltage VE remains almost constant with the increasing emitter current.

Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Description : Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Last Answer : Frequency of oscillation is given by,

State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Description : State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Last Answer : Basic Principle: The main principle of a piezoelectric crystal is that a mechanical force, when applied on the crystal, it vibrates and produces electric charges on the crystal surface. When ac voltage is applied across crystal, it vibrates at the frequency of the applied voltage. (OR)

Draw the input and output characteristics of CE configuration.

Description : Draw the input and output characteristics of CE configuration.

Last Answer : Input characteristics of CE configuration: Output characteristics of CE configuration:

Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Description : Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Last Answer : Circuit Diagram Waveform: Here transistor Q1 acts as a switch and transistor Q2 acts as an emitter follower (i.e. a unit gain amplifier).  Circuit Operation: Initially transistor ... The circuit pulls itself up by its own bootstrap and hence it is known as bootstrap sweep circuit. 

Draw the construction of p-channel D-MOSFET and state its working principle.

Description : Draw the construction of p-channel D-MOSFET and state its working principle. 

Last Answer : Construction of p-channel D-MOSFET: Working principle: The gate to source voltage is set to zero volts by the direct connection from one terminal to the other & voltage VDS is applied ... The value of voltage of VGS at which drain current nearly becomes zero is called cut off voltage. 

Draw the drain characteristics of p-channel FET and explain.

Description : Draw the drain characteristics of p-channel FET and explain.

Last Answer : Drain characteristics:- As VDS is increased from zero as shown , ID will increased proportionally through the p channel. In this region the channel resistance is constants because the depletion region is ... the depletion layer. (i.e. channel width zero) is called cutoff voltage or VGS(off).

Draw the circuit and explain the operation of UJT relaxation oscillator.

Description : Draw the circuit and explain the operation of UJT relaxation oscillator. 

Last Answer : Working: When the supply voltage (VCC) is switched ON, the capacitor charges through resistor (R), till the capacitor voltage reaches the voltage level (VP) which is called as peak point voltage. At ... resistor R is shown as a variable resistor. The sweep period is given by the relation

Draw the transfer characteristics for N-channel JFET.

Description : Draw the transfer characteristics for N-channel JFET.

Last Answer : Transfer characteristics for N-channel JFET: 

Define the following terms: (i) Stabilization (ii) Thermal runaway

Description : Define the following terms: (i) Stabilization (ii) Thermal runaway

Last Answer : Stabilization: The process of making operating point independent of temperature changes or variation in transistor parameter is known as stabilization. The maintenance of the operating point stable is called the ... happens, the device gets burnt out. This process is known as Thermal Runaway .

State the need of biasing and describe the concept of DC load line

Description : State the need of biasing and describe the concept of DC load line

Last Answer : Need of Biasing for Transistor: The transistor should be biased in the active region if it is to be used for amplification and in saturation and cut off if it is used as a switch. 2. The Q ... The position of operating point on the load line is dependent on the application of the transistor.

State the need of regulation. Explain the concept of load & line regulation.

Description : State the need of regulation. Explain the concept of load & line regulation.

Last Answer : Need of Regulation: The major disadvantage of a power supply is that the output voltage changes with the variations in the input voltage or the DC output voltage of the rectifier also increase similarly. In ... the change in output voltage that will occur per unit change in the input voltage. 

State the working principle of UJT

Description : State the working principle of UJT

Last Answer : Figure shows the equivalent circuit of a unijunction transistor with voltage source VEE connected across emitter and base 1 and VBB connected across base 1 and base 2. Hence the Emitter diode is reversed ... emitter current begins to flow ,the UJT is said to be fired, triggered or turned on.

Sketch p-channel JFET construction.

Description : Sketch p-channel JFET construction.

Last Answer : p- channel JFET constructional diagram:

Draw symbol for n-channel and p-channel MOSFET.

Description : Draw symbol for n-channel and p-channel MOSFET.

Last Answer : Symbol n-channel and p-channel MOSFET :   OR  

Define Q-point

Description : Define Q-point 

Last Answer : Q-point: For proper operation of transistor, in any application, we set fixed levels of certain voltages and currents in a transistor. These values of currents and voltages define the point, at which ... . This point is called operating point. It is also known as quiescent point or Q point.

List the applications of instrumentation amplifier.

Description : List the applications of instrumentation amplifier.

Last Answer : a. Temperature indicator b. Temperature controller c. Light intensity meters d. Water flow meter c. Thermal conductivity meter f. Analog weight scale

List the features of instrumentation amplifier:

Description : List the features of instrumentation amplifier:

Last Answer : 1.High gain accuracy 2.High CMRR 3.High gain stability with low temperature co-efficient 4Low dc offset 5.Low output impedance

State the need of signal conditioning and signal processing .List applications of instrumentation amplifier.

Description : State the need of signal conditioning and signal processing .List applications of instrumentation amplifier.

Last Answer : * In an instrumentation system, a transducer is used for sensing various parameters. The output of transducer is an electrical signal proportional to the physical quantity sensed such as pressure, ... monitoring and control 5) Light intensity meter 6) Measurement of flow and thermal conductivity

List the advantages of RC coupled amplifier.

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

Give the different types of amplifier coupling.

Description : Give the different types of amplifier coupling.

Last Answer : 1. Resistance – capacitance (RC) coupling.  2. Inductance (LC) coupling.  3. Transformer coupling (TC)  4. Direct coupling (D.C.)

What is the peak power of the Crunch Power Zone P18004 4-Channel Car Amplifier?

Description : What is the peak power of the Crunch Power Zone P18004 4-Channel Car Amplifier?

Last Answer : Its peak power is 1800W: 2 x 900 W @ 4 Ohms Maxx Power.

How big is the Alpine V-Power MRP-F300 4-Channel Car Amplifier?

Description : How big is the Alpine V-Power MRP-F300 4-Channel Car Amplifier?

Last Answer : According to Alpine's website the dimensions are (WxHxD) in: 10-15/16'' x 2-23/64'' x 9-27/32''

Can I use an amplifier which provides less power than my speakers need?

Description : Can I use an amplifier which provides less power than my speakers need?

Last Answer : If you use a lower rated amplifier than your speakers, your speakers won't be able to be as loud but won't suffer any damage.

Is the Crunch Power Zone P18004 4-Channel Car Amplifier good for any kind of music?

Description : Is the Crunch Power Zone P18004 4-Channel Car Amplifier good for any kind of music?

Last Answer : Is good for all kinds of music. It can be connect and has the power to connect to a verity of speaks, letting you choose the right speak for the right sound you're looking for.

How do you hook up the power to the Alpine V-Power MRP-F300 4-Channel Car Amplifier?

Description : How do you hook up the power to the Alpine V-Power MRP-F300 4-Channel Car Amplifier?

Last Answer : Usually, it is best to make all of the new stereo's wiring connections through your car's wiring harness.Directly connecting it to the power is more complicated and risky.

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to maintain constant engine speed with increased load B. send a kilowatt signal to the metering circuit C. shutting down the prime mover in the event of reverse power to protect from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Description : In the illustrated electronic governor, the circuit card connected to the potential and current transformers is for ________. EL-0046 A. increasing the signal strength to the governor to ... from motorization D. conditioning the load through the use of a magnetic amplifier current transformer

Last Answer : Answer: A

In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

As shown in the illustrations, ordered rudder angle is fed back from the ________________. EL-0097 A. power unit to the magnetic amplifier B. steering gear to the control potentiometer C. magnetic amplifier to the steering gear D. rudder yoke to the non-followup controller

Description : As shown in the illustrations, ordered rudder angle is fed back from the ________________. EL-0097 A. power unit to the magnetic amplifier B. steering gear to the control potentiometer C. magnetic amplifier to the steering gear D. rudder yoke to the non-followup controller

Last Answer : Answer: A