State any four applications of transistor.

2 Answers

Answer :

Application:

1) Amplifier

2) Switching application

3) Oscillators

4) Wave shaping circuits

5) Logic circuits

6) Timer and Multivibrator

7) Delay circuits

Answer :

Amplifier

Related questions

Description : Explain the operating principle of PNP transistor. 

Last Answer : The circuit connection of PNP transistor with supply voltages is as shown above. The emitter-base junction is connected as forward bias. Due to this the emitter pushes the holes from the P ... by the collector. This develops the collector current IC. This is how a PNP transistor operates. 

Description : State and explain the working principle of FET amplifier and list its applications.

Last Answer : Operation of FET amplifier: When small a.c. signal is applied to the gate, it produces variation in the gate to source voltage. This results in variation in the drain current. As ... input voltage.  Application: Buffer amplifier Low noise amplifier Cascade amplifier Chopper amplifier

Description : List applications of power amplifier.

Last Answer : Below are the applications of power amplifiers across different sectors: 1.Consumer Electronics: Audio power amplifiers are used in almost all consumer electronic devices ranging from microwave ovens, ... data transfer rates and usability. They are also used in satellite communication equipment.

Description : Mention the applications of transistor.

Last Answer : a) Transistor is used in amplifier. b) It is used in oscillator. c) It is used in switching circuits.

Description : State 2 advantages of JFET over BJT.

Last Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

Description : Draw the characteristics of UJT and state its working principle.

Last Answer : The characteristics of Unijunction Transistor (UJT) can be explained by three parameters: * Cutoff Region * Negative Resistance Region * Saturation Region Cutoff Region : The ... in its ON position. The emitter voltage VE remains almost constant with the increasing emitter current.

Description : Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Last Answer : Frequency of oscillation is given by,

Description : Draw the circuit of single tuned amplifier and state its operating principle.

Last Answer : Operating Principle: The working of tuned voltage amplifier may be understood by considering a radio frequency signal, to be amplified applied at the input of the amplifier. The resonant frequency ... will be amplified. And all the other frequencies will be rejected by the tuned circuit. 

Description : State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Last Answer : Basic Principle: The main principle of a piezoelectric crystal is that a mechanical force, when applied on the crystal, it vibrates and produces electric charges on the crystal surface. When ac voltage is applied across crystal, it vibrates at the frequency of the applied voltage. (OR)

Description : Draw the construction of p-channel D-MOSFET and state its working principle. 

Last Answer : Construction of p-channel D-MOSFET: Working principle: The gate to source voltage is set to zero volts by the direct connection from one terminal to the other & voltage VDS is applied ... The value of voltage of VGS at which drain current nearly becomes zero is called cut off voltage. 

Description : Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Last Answer : Advantages: 1. It has a wide frequency response. 2. For coupling the resistor and the capacitor are used and which are not expensive so the cost is low. 3. The circuit is very ... a wide frequency band. 5. It is high fidelity amplifier. 6. It provides less frequency distortion.

Description : State the need of biasing and describe the concept of DC load line

Last Answer : Need of Biasing for Transistor: The transistor should be biased in the active region if it is to be used for amplification and in saturation and cut off if it is used as a switch. 2. The Q ... The position of operating point on the load line is dependent on the application of the transistor.

Description : State the need of regulation. Explain the concept of load & line regulation.

Last Answer : Need of Regulation: The major disadvantage of a power supply is that the output voltage changes with the variations in the input voltage or the DC output voltage of the rectifier also increase similarly. In ... the change in output voltage that will occur per unit change in the input voltage. 

Description : State the working principle of UJT

Last Answer : Figure shows the equivalent circuit of a unijunction transistor with voltage source VEE connected across emitter and base 1 and VBB connected across base 1 and base 2. Hence the Emitter diode is reversed ... emitter current begins to flow ,the UJT is said to be fired, triggered or turned on.

Description : State the need and types of amplifier coupling. 

Last Answer : Need of amplifier coupling: 1.When ever large amplifier with very good impedance matching is required, a signal stage amplifier circuit will not able to amplify the signal to a large extent. 2 ... 2.Transformer coupled amplifier 3.Direct coupled amplifier 4. Inductance (LC) coupling

Description : Define intrinsic standoff ratio.

Last Answer : It is defined as the ratio of the RB1 (base resistance 1) to the inter-base resistance RBB. 

Description : List the types of power amplifier.

Last Answer : Types of Power amplifier: 1) Class A power amplifier 2) Class B power amplifier 3) Class AB power amplifier 4) Class C power amplifier

Description : Sketch the single tuned amplifier.

Last Answer : single tuned amplifier

Description : Which type of MOSFET is called Normally ON MOSFET”? Why? 

Last Answer : DMOSFET is called Normally ON MOSFET. In DMOSFET already channel is present and at Vgs = 0v, drain current Id=Idss i.e. drain to source saturation current is flowing. 

Description : Define gain and bandwidth. 

Last Answer : Gain: It is the ratio of output quantity to the input quantity. Bandwidth: It is defined as the range (band) of frequency over which the gain is constant.  (Or) It is the range of frequency over which the gain is greater than 70.7% of the maximum gain possible

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Description : Draw the input and output characteristics of CE configuration.

Last Answer : Input characteristics of CE configuration: Output characteristics of CE configuration:

Description : Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Last Answer : Circuit Diagram Waveform: Here transistor Q1 acts as a switch and transistor Q2 acts as an emitter follower (i.e. a unit gain amplifier).  Circuit Operation: Initially transistor ... The circuit pulls itself up by its own bootstrap and hence it is known as bootstrap sweep circuit. 

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Last Answer : Parameter Class A Class B 

Description : Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Last Answer : Diagram of complementary symmetry Class B push-pull amplifier: Working: The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input ... of class B, this circuit is termed as Complementary symmetry push pull class B amplifier.

Description : Draw the drain characteristics of p-channel FET and explain.

Last Answer : Drain characteristics:- As VDS is increased from zero as shown , ID will increased proportionally through the p channel. In this region the channel resistance is constants because the depletion region is ... the depletion layer. (i.e. channel width zero) is called cutoff voltage or VGS(off).

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

Description : Draw the circuit and explain the operation of UJT relaxation oscillator. 

Last Answer : Working: When the supply voltage (VCC) is switched ON, the capacitor charges through resistor (R), till the capacitor voltage reaches the voltage level (VP) which is called as peak point voltage. At ... resistor R is shown as a variable resistor. The sweep period is given by the relation

Description : Draw the transfer characteristics for N-channel JFET.

Last Answer : Transfer characteristics for N-channel JFET: 

Description : Define the following terms: (i) Stabilization (ii) Thermal runaway

Last Answer : Stabilization: The process of making operating point independent of temperature changes or variation in transistor parameter is known as stabilization. The maintenance of the operating point stable is called the ... happens, the device gets burnt out. This process is known as Thermal Runaway .

Description : Sketch p-channel JFET construction.

Last Answer : p- channel JFET constructional diagram:

Description : Draw symbol for n-channel and p-channel MOSFET.

Last Answer : Symbol n-channel and p-channel MOSFET :   OR  

Description : Define Q-point 

Last Answer : Q-point: For proper operation of transistor, in any application, we set fixed levels of certain voltages and currents in a transistor. These values of currents and voltages define the point, at which ... . This point is called operating point. It is also known as quiescent point or Q point.

Description : Name two types of BJT &draw their symbols. 

Last Answer : Two types of BJT: * NPN * PNP 

Description : What are the four classes of operation of a transistor amplifier?

Last Answer : A, AB, B, C.

Description : A transistor has (A) One p-n junction. (B) Two p-n junction. (C) Four p-n junction. (D) Five p-n junction.

Last Answer : (B) Two p-n junction.

Description : State any four applications of a communication satellite.

Last Answer : State any four applications of a communication satellite.

Description : State any four applications of spectrum analyzer.

Last Answer : Applications: 1. Spectrum analyzer is a very important item of test equipment for someone designing or repairing electronic equipment that uses radio frequency signals. 2. Its key factor is that it is ... of the dominant frequency within a signal 8. Used to measure the properties of RF devices

Description : State and explain any four field applications of Geotechnical Engineering.

Last Answer : Field applications of Geotechnical Engineering are as follows:  1. Design of foundation for various structures: Foundation is required to transfer the load of super structure to foundation soil and to ... of beds. GTE is necessary to study shear strength, permeability of soil for such structure.

Description : State four applications of PIN diode. 

Last Answer : i. Used in rectifier circuit. ii. Used in clipping and clamping circuit. iii. Used for A.M detection. iv. Used for voltage multiplier.

Description : Draw construction of Schottky diode and state it’s four applications.

Last Answer : Applications :- 1. RF mixer and detector diode: 2. Power rectifier 3. Voltage clamping 4. Stand alone photovoltaic systems in order to prevent batteries from discharging purpose for the solar panels at night 5. Rectifiers in power supplies.

Description : State any Four applications of PN junction diode.

Last Answer : 1. Rectifiers in power supplies, 2. Detectors in RF, 3 .Clippers, 4. In clamping networks used as DC Restorers, 5. As switches in digital logic circuits.

Description : State any four types of grippers used in robots with one applications of each.

Last Answer : [1] Vacuum Gripper:- Flat and light weight Surfaces / Palletizing materials [2] Pneumatic Gripper:- Slightly weight parts [3] Hydraulic Gripper:- Heavy parts in industry [4] Servo electric ... objects such as steel sheets or tables [6] Claw Grippers:- Pick and lace and Assembly operations

Description : State the working principle of Cam. List its types. Give any four applications of Cam.

Last Answer : Working principle of CAM: A cam is mechanical rotating machine element which is used for converting one motion in to another. It is rotating machine element that gives reciprocating or ... control mechanisms. Spinning and weaving machineries. Textile machineries. Paper cutting machines.

Description : State any four applications of contour map

Last Answer : Following are the applications of Contour map. 1. With the help of contour lines on contour map one can know the nature of ground. 2. For determination of most economical site for dams ... of cutting and embankment in given gradient. 6. For determining the indivisibility of two given points

Description : State any four applications of resistance welding. 

Last Answer : Answer: Applications of resistance welding: 1. Resistance welding is widely used in automotive industries. 2. Projection welding is widely used in production of nut and bolt. Projection welding is ... welding is applied in manufacturing of wheel rims, wire joints and railway track joints etc. 

Description : State the principle used in Lapping. List four applications of Lapping.

Last Answer : Principle of Lapping: Lapping is basically an abrasive process in which loose abrasives function as cutting points finding momentary support of the lap. The process has the following features. (a) Use of ... roller bearings ii. Gears iii. Piston rings iv. Slip gauges v. Crankshaft.

Description : State any four applications of OPP.

Last Answer : Applications of OOP: Real time systems Simulation and modeling Object-oriented databases Hypertext, hypermedia and expert Ext AI and expert systems Neural networks and parallel programming Decision support and office automation systems CIM/CAM/CAD systems

Description : State two advantages and disadvantages of centrifugal casting. Write four applications.

Last Answer : Centrifugal Casting: Advantages: 1. Relatively very light impurities move inwards towards center. So they can be removed easily thus helping in producing sound castings. 2. Gates and risers are not needed. ... making rollers. 4. Piston rings. 5. Cylinder liners. 6. Pipes of water gas sewage.

Description : State any four applications of regulated DC power supply.

Last Answer : * Amplifiers * Mobile Phone power adaptors * Regulated power supplies in appliances * Various oscillators