Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.
by

1 Answer

Answer :

image

Frequency of oscillation is given by,

image

by

Related questions

Draw and explain RC phase shift Oscillator.

Description : Draw and explain RC phase shift Oscillator.

Last Answer : Circuit diagram of RC phase shift oscillator: WORKING: * Circuit consists of a single stage amplifier in common emitter configuration & RC phase shifting network. * R1, R2, RE provides biasing & CE ... . * The phase shift around the loop is 3600 only at one precise frequency.  

State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Description : State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Last Answer : Basic Principle: The main principle of a piezoelectric crystal is that a mechanical force, when applied on the crystal, it vibrates and produces electric charges on the crystal surface. When ac voltage is applied across crystal, it vibrates at the frequency of the applied voltage. (OR)

Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Description : Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Last Answer : Advantages: 1. It has a wide frequency response. 2. For coupling the resistor and the capacitor are used and which are not expensive so the cost is low. 3. The circuit is very ... a wide frequency band. 5. It is high fidelity amplifier. 6. It provides less frequency distortion.

Draw the circuit and explain the operation of UJT relaxation oscillator.

Description : Draw the circuit and explain the operation of UJT relaxation oscillator. 

Last Answer : Working: When the supply voltage (VCC) is switched ON, the capacitor charges through resistor (R), till the capacitor voltage reaches the voltage level (VP) which is called as peak point voltage. At ... resistor R is shown as a variable resistor. The sweep period is given by the relation

Compare between RC phase shift oscillator and crystal oscillator.

Description : Compare between RC phase shift oscillator and crystal oscillator.

Last Answer : RC phase shift oscillator Crystal oscillator This oscillator is used for low frequency range. Quartz crystal is mainly used in radio-frequency (RF) oscillators Used resistor and capacitor ... RC network is used as feedback network. Crystal is connected in feedback.

Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Description : Draw neat labeled diagram of single phase AC locomotive showing its various equipments of power circuit and give function of each equipment used in power circuit.

Last Answer : Functions of equipment: 1) circuit breaker: disconnects the locomotive equipment from the supply in the event of fault in the equipment / loco. 2) On load tap changer, used to control the ... 6) Traction motor: operates as per the required operating characteristics to take on the traction load.

Draw the circuit of single tuned amplifier and state its operating principle.

Description : Draw the circuit of single tuned amplifier and state its operating principle.

Last Answer : Operating Principle: The working of tuned voltage amplifier may be understood by considering a radio frequency signal, to be amplified applied at the input of the amplifier. The resonant frequency ... will be amplified. And all the other frequencies will be rejected by the tuned circuit. 

Draw the frequency response of DC amplifier. Comment on it.

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

What is phase-shift oscillator?

Description : What is phase-shift oscillator?

Last Answer : A phase-shift oscillator is a simple electronic oscillator. It contains an inverting amplifier, and a feedback filter which 'shifts' the phase of the amplifier output by 180 degrees at the oscillation ... 180° at high frequencies, so that the phase shift at the desired oscillation frequency is 180°.

The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Description : The major function of transistor. Q2 is A) It provides voltage gain B) It provides the feedback signal C) It isolates the oscillator from loading effects D) It provides a phase shift.

Last Answer : ) It provides a phase shift.

Why is a high-gain transistor used in the phase-shift oscillator?

Description : Why is a high-gain transistor used in the phase-shift oscillator?

Last Answer : Because of the losses encountered in the RC networks.

Which components provide the regenerative feedback signal in the phase-shift oscillator?

Description : Which components provide the regenerative feedback signal in the phase-shift oscillator?

Last Answer : Resistor-capacitor networks.

In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Description : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be -

Last Answer : In an R-C phase shift oscillator, the minimum no. of R-C networks to be connected in cascade will be 3

Oscillator independent of phase shift is

Description : Oscillator independent of phase shift is  (1) Relaxation (2) Wein bridge (3) Clapp (4) All of these

Last Answer : Oscillator independent of phase shift is Relaxation 

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Description : Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Last Answer : Circuit Diagram Waveform: Here transistor Q1 acts as a switch and transistor Q2 acts as an emitter follower (i.e. a unit gain amplifier).  Circuit Operation: Initially transistor ... The circuit pulls itself up by its own bootstrap and hence it is known as bootstrap sweep circuit. 

Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Description : Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Last Answer : Diagram of complementary symmetry Class B push-pull amplifier: Working: The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input ... of class B, this circuit is termed as Complementary symmetry push pull class B amplifier.

Compare RC and LC oscillator.

Description : Compare RC and LC oscillator.

Last Answer :  RC and LC oscillator

List the applications of RC oscillator and crystal oscillator.

Description : List the applications of RC oscillator and crystal oscillator.

Last Answer : Applications of RC oscillator :  1) In AF signal generators 2) In radio transmitter & Receivers 3) Sine wave generator.  Applications of Crystal oscillator : 1) Electronic navigation systems 2) Frequency Synthesizers 3) Timing circuits (Clock) with high stability. 4) RADAR systems. 

Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Description :  Draw a neat labeled block diagram of 3-phase Electronic Energy meter.

Last Answer : Labeled diagram of 3-phase electronic energy meter:

Draw the characteristics of UJT and state its working principle.

Description : Draw the characteristics of UJT and state its working principle.

Last Answer : The characteristics of Unijunction Transistor (UJT) can be explained by three parameters: * Cutoff Region * Negative Resistance Region * Saturation Region Cutoff Region : The ... in its ON position. The emitter voltage VE remains almost constant with the increasing emitter current.

Draw the construction of p-channel D-MOSFET and state its working principle.

Description : Draw the construction of p-channel D-MOSFET and state its working principle. 

Last Answer : Construction of p-channel D-MOSFET: Working principle: The gate to source voltage is set to zero volts by the direct connection from one terminal to the other & voltage VDS is applied ... The value of voltage of VGS at which drain current nearly becomes zero is called cut off voltage. 

Draw neat labeled diagram of AC track circuit. Also give two advantages of AC track circuit.

Description : Draw neat labeled diagram of AC track circuit. Also give two advantages of AC track circuit.

Last Answer : AC Track Circuit:  Advantages of AC Track Circuit: 1. Free from effects of stray currents. 2. Track circuit is up to a long length of track in one section length up to 3km to 5 km. 3. Cheaper in costs as compared to DC track circuit. 4. Easy to install than DC track circuit. 

Draw the circuit diagram of crystal oscillator and explain its working.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC ) 

Draw and explain Hartley Oscillator circuit diagram.

Description : Draw and explain Hartley Oscillator circuit diagram.

Last Answer : Function of each component: 1. An NPN transistor connected in a common emitter configuration works as the active device in amplifier stage and CE configuration provides 180°phase shift. 2. R1 and R2 ... circuit to the base-emitter circuit.  The frequency of oscillation is given as-  

Draw RC differentiator circuit.

Description : Draw RC differentiator circuit.

Last Answer : RC differentiator circuit :

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Description : Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Last Answer : Operation:- The capacitors C1 and C2 are called as the coupling capacitors. As the load resistor RL (not shown in the diagram) is coupled to the amplifier through the coupling capacitor ... connected in the common emitter (CE) configuration. Therefore, this amplifier is called CE amplifier. 

Time constant for RC circuit formula

Description : Time constant for RC circuit formula τ = RC Where, τ = time constant

Last Answer : Time constant for RC circuit formula τ = RC Where, τ = time constant

What transmission method uses a stable cw reference oscillator, which is locked in phase with the transmitter frequency?

Description : What transmission method uses a stable cw reference oscillator, which is locked in phase with the transmitter frequency?

Last Answer : Pulse-Doppler.

Draw the input and output characteristics of CE configuration.

Description : Draw the input and output characteristics of CE configuration.

Last Answer : Input characteristics of CE configuration: Output characteristics of CE configuration:

Draw the drain characteristics of p-channel FET and explain.

Description : Draw the drain characteristics of p-channel FET and explain.

Last Answer : Drain characteristics:- As VDS is increased from zero as shown , ID will increased proportionally through the p channel. In this region the channel resistance is constants because the depletion region is ... the depletion layer. (i.e. channel width zero) is called cutoff voltage or VGS(off).

Draw the transfer characteristics for N-channel JFET.

Description : Draw the transfer characteristics for N-channel JFET.

Last Answer : Transfer characteristics for N-channel JFET: 

Draw symbol for n-channel and p-channel MOSFET.

Description : Draw symbol for n-channel and p-channel MOSFET.

Last Answer : Symbol n-channel and p-channel MOSFET :   OR  

How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Description : How do you eliminate radio frequency variation of an oscillator transmitter caused by its supply voltage? A. Use new power supply B. Lossen power supply shielding C. Use of regulated power supply D. Use of high capacitor in the supply circuit

Last Answer : C. Use of regulated power supply

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to automatic/zero droop C. enable the operator to read the field voltage on device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Description : The device labeled 'REG SW' in the illustration is used to ___________. EL-0003 A. shift from the automatic voltage regulator to the manual voltage regulator B. shift the governor control from manual to ... device 'REG ADJ' or device 'MAN ADJ' D. supply regulated control power to the switchboard

Last Answer : Answer: A

Draw a labeled sketch of pump feed fuel supply system for petrol engine and state location and function of each component.

Description : Draw a labeled sketch of pump feed fuel supply system for petrol engine and state location and function of each component.

Last Answer : The pump feed system is shown in the figure above. Fuel tank is for storage of fuel located above the engine of two wheeler and in case of car located at backside of the car ... the tendency of forming vapor lock. The system provides the fuel requirement at various engine speeds efficiently. 

Draw a labeled block diagram of sine wave generator and state function of each block.

Description : Draw a labeled block diagram of sine wave generator and state function of each block. 

Last Answer : Function Generator:  This instrument can deliver sine, triangular & square waves with frequency range of 0.01 Hz to 100 kHz.  The frequency control network is governed by a frequency ... voltage reaches a predetermined level on the negative slope of the integrator's output voltage.

State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Description : State the condition for RC differentiator. Draw the output waveform of RC integrator for square wave input.

Last Answer : Condition for RC differentiator: If the time duration T of the input waveform is comparable with the RC time constant (product of R and C) then the output waveform of the differentiator gets distorted. Hence for proper differentiator the condition is as follows: T >>RC

What is a simplified difference between Phase Shift Keying and Frequency Shift Keying?

Description : What is a simplified difference between Phase Shift Keying and Frequency Shift Keying?

Last Answer : answer:FSK adjusts the frequency, PSK adjusts the phase. We use nonstandard PSK in our work because we can design a pre-amp and amp around the one frequency and design a filter with broad Q in the range of ... said ;-) Here is a good reference with pictures. If you need more then look at fsk vs psk

What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Description : What type of transmission is radiated from an aircraft’s radio altimeter antenna? A. An amplitude modulated continuous wave B. A pulse position modulated UHF signal C. A differential phase shift keyed UHF signal D. A frequency modulated continuous wave

Last Answer : D. A frequency modulated continuous wave

What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Description : Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Last Answer : D. 166.5˚

The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Description : The modulation technique used by GSM cellular system A. Phase shift keying B. Frequency shift keying C. Gaussian minimum shift keying D. QAM

Last Answer : C. Gaussian minimum shift keying

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Description : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Last Answer : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Draw neat labeled sketch of ply press.

Description : Draw neat labeled sketch of ply press.

Last Answer : sketch of ply press

Draw a neat labeled sketch of 30m chain.

Description : Draw a neat labeled sketch of 30m chain.

Last Answer : neat labeled sketch of 30m chain

Draw labeled sketch of prismatic compass.

Description : Draw labeled sketch of prismatic compass.

Last Answer : Sketch of prismatic compass :