. If Prandtl number is greater than the Schmidt number, then the (A) Thermal boundary layer lies inside the concentration boundary layer (B) Concentration boundary layer lies inside the thermal boundary layer (C) Thermal & concentration boundary layers are of equal thickness (D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other two

. If Prandtl number is greater than the Schmidt number, then the

(A) Thermal boundary layer lies inside the concentration boundary layer

(B) Concentration boundary layer lies inside the thermal boundary layer

(C) Thermal & concentration boundary layers are of equal thickness

(D) Hydrodynamic (i.e., momentum) boundary layer is thicker than the other

two

by

1 Answer

Answer :

(A) Thermal boundary layer lies inside the concentration boundary layer


by

Related questions

The hydrodynamic and thermal boundary layers will merge, when (A) Prandtl number is one (B) Schmidt number tends to infinity (C) Nusselt number tends to infinity (D) Archimedes number is greater than 10000

Description : The hydrodynamic and thermal boundary layers will merge, when (A) Prandtl number is one (B) Schmidt number tends to infinity (C) Nusselt number tends to infinity (D) Archimedes number is greater than 10000

Last Answer : (A) Prandtl number is one

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

For flow over a flat plate, the ratio of thermal boundary layer thickness, 'xt' and hydrodynamic boundary layer thickness 'x' is equal to (where, NPr = Prandtl number) (A) NPr (B) NPr 1/3 (C) NPr -1 (D) NPr -1/3

Description : For flow over a flat plate, the ratio of thermal boundary layer thickness, 'xt' and hydrodynamic boundary layer thickness 'x' is equal to (where, NPr = Prandtl number) (A) NPr (B) NPr 1/3 (C) NPr -1 (D) NPr -1/3

Last Answer : (B) NPr 1/3

Thickness of thermal boundary layer is more compared to that of hydrodynamic boundary layer, when the value of Prandtl number is (A) 1 (B) < 1 (C) > 1 (D) > 5

Description : Thickness of thermal boundary layer is more compared to that of hydrodynamic boundary layer, when the value of Prandtl number is (A) 1 (B) < 1 (C) > 1 (D) > 5

Last Answer : (B) < 1

The thermal boundary layer at NPr > 1 (A) Is thicker than hydrodynamic boundary layer (B) Is thinner than hydrodynamic boundary layer (C) And the hydrodynamic boundary layers are identical (D) Disappears

Description : The thermal boundary layer at NPr > 1 (A) Is thicker than hydrodynamic boundary layer (B) Is thinner than hydrodynamic boundary layer (C) And the hydrodynamic boundary layers are identical (D) Disappears

Last Answer : (B) Is thinner than hydrodynamic boundary layer

At what value of Prandtl number, the hydrodynamic and thermal boundary layers of a fluid flowing over a heated plate will be identical? (A) 1 (B) < 1 (C) > 1 (D) None of these

Description : At what value of Prandtl number, the hydrodynamic and thermal boundary layers of a fluid flowing over a heated plate will be identical? (A) 1 (B) < 1 (C) > 1 (D) None of these

Last Answer : (A) 1

The ratio of hydrodynamic boundary layer to thermal boundary layer thickness in case of liquid metals is (A) < 1 (B) 1 (C) > 1 (D) 2

Description : The ratio of hydrodynamic boundary layer to thermal boundary layer thickness in case of liquid metals is (A) < 1 (B) 1 (C) > 1 (D) 2

Last Answer : (A) < 1

How the thickness of thermal boundary layer and thickness of hydrodynamic boundary layer related ?

Description : How the thickness of thermal boundary layer and thickness of hydrodynamic boundary layer related ?

Last Answer : Ratio of their thickness = (Prandtl number)-1/3.

02. The separation of flow occurs when the hydrodynamic boundary layer thickness is reduced to zero. A) AgreeB) Disagree

Description : 02. The separation of flow occurs when the hydrodynamic boundary layer thickness is reduced to zero. A) Agree B) Disagree

Last Answer : A

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

In physical terms, Schmidt number means (A) Thermal diffusivity/mass diffusivity(B) Thermal diffusivity/momentum diffusivity(C) Momentum diffusivity/mass diffusivity(D) Mass diffusivity/thermal diffusivity

Description : In physical terms, Schmidt number means (A) Thermal diffusivity/mass diffusivity (B) Thermal diffusivity/momentum diffusivity (C) Momentum diffusivity/mass diffusivity (D) Mass diffusivity/thermal diffusivity

Last Answer : (C) Momentum diffusivity/mass diffusivity

The Schmidt number which is defined as, μ/ρ D, is the ratio of the (A) Momentum diffusivity to the mass diffusivity (B) Thermal diffusivity to the mass diffusivity (C) Momentum diffusivity to the thermal diffusivity (D) None of these

Description : The Schmidt number which is defined as, μ/ρ D, is the ratio of the (A) Momentum diffusivity to the mass diffusivity (B) Thermal diffusivity to the mass diffusivity (C) Momentum diffusivity to the thermal diffusivity (D) None of these

Last Answer : (A) Momentum diffusivity to the mass diffusivity

Prandtl number is the ratio of (A) Mass diffusivity to thermal diffusivity (B) Momentum diffusivity to thermal diffusivity (C) Thermal diffusivity to mass diffusivity (D) Thermal diffusivity to momentum diffusivity

Description : Prandtl number is the ratio of (A) Mass diffusivity to thermal diffusivity (B) Momentum diffusivity to thermal diffusivity (C) Thermal diffusivity to mass diffusivity (D) Thermal diffusivity to momentum diffusivity

Last Answer : (B) Momentum diffusivity to thermal diffusivity

The ratio of momentum diffusivity to thermal diffusivity is the __________ number. (A) Prandtl (B) Nusselt (C) Stanton (D) Grashoff

Description : The ratio of momentum diffusivity to thermal diffusivity is the __________ number. (A) Prandtl (B) Nusselt (C) Stanton (D) Grashoff

Last Answer : (A) Prandtl

Prandtl number is the ratio of (A) Momentum diffusivity to mass diffusivity (B) Momentum diffusivity to thermal diffusivity (C) Thermal diffusivity to mass diffusivity (D) Thermal diffusivity to momentum diffusivity

Description : Prandtl number is the ratio of (A) Momentum diffusivity to mass diffusivity (B) Momentum diffusivity to thermal diffusivity (C) Thermal diffusivity to mass diffusivity (D) Thermal diffusivity to momentum diffusivity

Last Answer : (B) Momentum diffusivity to thermal diffusivity

Prandtl number is the reciprocal of (A) Thermal diffusivity/Momentum diffusivity (B) Thermal diffusivity × Momentum (C) Thermal diffusivity × Mass diffusivity (D) Mass diffusivity × Momentum diffusivity

Description : Prandtl number is the reciprocal of (A) Thermal diffusivity/Momentum diffusivity (B) Thermal diffusivity × Momentum (C) Thermal diffusivity × Mass diffusivity (D) Mass diffusivity × Momentum diffusivity

Last Answer : (A) Thermal diffusivity/Momentum diffusivity

A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature difference across the wall is 36°C. The temperature difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24

Description : A wall has two layers of materials A and B; each made of a different material. Both the layers have the same thickness. The thermal conductivity of material A is twice that of B. Under the equilibrium, the temperature ... difference across the layer A is __________ °C. (A) 6 (B) 12 (C) 18 (D) 24

Last Answer : (B) 12

The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Description : The major reason of hydrodynamic noise (i.e., noise resulting from liquid flow) is (A) Pipe vibrations (B) Cavitation (C) Boundary layer separation (D) Fluctuation in liquid flow

Last Answer : (B) Cavitation

Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Schmidt (B) Sherwood (C) Peclet (D) Stanton

Description : Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Schmidt (B) Sherwood (C) Peclet (D) Stanton

Last Answer : (A) Schmidt

Which of the following plays an important role in problems of simultaneous heat and mass transfer?(A) Lewis number (B) Schmidt number (C) Prandtl number (D) Sherwood number

Description : Which of the following plays an important role in problems of simultaneous heat and mass transfer (A) Lewis number (B) Schmidt number (C) Prandtl number (D) Sherwood number

Last Answer : (A) Lewis number

Pick out the wrong statement pertaining to the analogy between equations of heat and mass transfer operations. (A) Sherwood number in mass transfer is analogous to Nusselt number in heat transfer (B) Prandtl number in heat transfer is analogous to Schmidt number in mass transfer (C) Reynolds number in mass transfer is analogous to Grashoff number in heat transfer (D) Reynolds number remains the same in both heat and mass transfer

Description : Pick out the wrong statement pertaining to the analogy between equations of heat and mass transfer operations. (A) Sherwood number in mass transfer is analogous to Nusselt number in heat transfer ... heat transfer (D) Reynolds number remains the same in both heat and mass transfer

Last Answer : (C) Reynolds number in mass transfer is analogous to Grashoff number in heat transfer

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

The dimensionless group in mass transfer that is equivalent to Prandtl number in heat transfer is (A) Nusselt number (B) Sherwood number (C) Schmidt number (D) Stanton numbe

Description : The dimensionless group in mass transfer that is equivalent to Prandtl number in heat transfer is (A) Nusselt number (B) Sherwood number (C) Schmidt number (D) Stanton numbe

Last Answer : (C) Schmidt number

The non-dimensional temperature gradient in a liquid at the wall of a pipe is the (A) Heat flux (B) Nusselt number (C) Prandtl number (D) Schmidt number

Description : The non-dimensional temperature gradient in a liquid at the wall of a pipe is the (A) Heat flux (B) Nusselt number (C) Prandtl number (D) Schmidt number

Last Answer : (A) Heat flux

The length of the tube necessary for the boundary layer to reach thecentre of the tube and for fully developed flow to be established is called the__________ length.(A) Equivalent(B) Transition(C) Prandtl mixing(D) None of these

Description : The length of the tube necessary for the boundary layer to reach thecentre of the tube and for fully developed flow to be established is called the __________ length. (A) Equivalent (B) Transition (C) Prandtl mixing (D) None of these

Last Answer : (B) Transition

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number(A) Increases(B) Decreases(C) Remain same(D) May increase or decrease.

Description : The boundary layer thickness at a given section along a flat plate __________ with increasing Reynold's number. (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease

Last Answer : (B) Decreases

Air over the oceans is colder in summer and warmer in winter compared with air over the continental regions. This is because (a) Water is translucent and has a relatively high heat capacity compared to dirt (b) Compared to dirt, a thicker layer of water participates in the seasonal cycle (c) The albedo of water is greater than that of land and thus reflects more solar radiation (d) Both A and B are true (e) The effect is due to the changes in circulation between continents and oceans

Description : Air over the oceans is colder in summer and warmer in winter compared with air over the continental regions. This is because (a) Water is translucent and has a relatively high heat capacity compared ... B are true (e) The effect is due to the changes in circulation between continents and oceans

Last Answer : (d) Both A and B are true

There are five concentric layers within the atmosphere which is differentiated on the basis of temperature. The atmospheric layer which lies close to the earth's surface in which human being along with other organisms live is called troposphere. The rate at which air temperature in the troposphere gradually decreases with height is about __________ °C/km. (A) 0.05 (B) 1 (C) 6.5 (D) 15

Description : There are five concentric layers within the atmosphere which is differentiated on the basis of temperature. The atmospheric layer which lies close to the earth's surface in which human being along with other organisms live is called ... is about __________ °C/km. (A) 0.05 (B) 1 (C) 6.5 (D) 15

Last Answer : (C) 6.5

For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

Description : For flow past a flat plate, if ‘x’ is the distance along the plate in the direction of flow, the boundary layer thickness is proportional to (A) √x (B) 1/√x (C) x (D) 1/x Answe

Last Answer : (A) √x

Boundary layer separation is caused by the (A) Reduction of pressure to vapour pressure (B) Boundary layer thickness reducing to zero (C) Adverse pressure gradient (D) Reduction of pressure gradient to zero

Description : Boundary layer separation is caused by the (A) Reduction of pressure to vapour pressure (B) Boundary layer thickness reducing to zero (C) Adverse pressure gradient (D) Reduction of pressure gradient to zero

Last Answer : (D) Reduction of pressure gradient to zero

Boundary layer separation is caused by the (A) Reduction of pressure below vapour pressure (B) Reduction of pressure gradient to zero (C) Adverse pressure gradient (D) Reduction of boundary layer thickness to zero

Description : Boundary layer separation is caused by the (A) Reduction of pressure below vapour pressure (B) Reduction of pressure gradient to zero (C) Adverse pressure gradient (D) Reduction of boundary layer thickness to zero

Last Answer : (C) Adverse pressure gradient

What is the ratio of displacement thickness to nominal thickness for a linear distribution of velocity in the boundary layer on a flat plate? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Description : What is the ratio of displacement thickness to nominal thickness for a linear distribution of velocity in the boundary layer on a flat plate? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Last Answer : (A) 0.5

In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Description : In a boundary layer developed along the flow, the pressure decreases in the downstream direction. The boundary layer thickness in this case will (A) Decrease gradually (B) Increase gradually (C) Increase rapidly (D) Remain constant

Last Answer : (B) Increase gradually

The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Description : The laminar boundary layer thickness in zero pressure gradient flow over a flat plate along the x-direction varies as x0.5 while the thickness of turbulent boundary layer varies as (where, x = distance from the leading edge) (A) x1.5 (B) x0.8 (C) x-1.5 (D) x-0.8

Last Answer : (B) x0.8

A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature at the two sides of the wall are 400 and 1200°K, then the temperature drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Description : A composite flat wall of a furnace is made of two materials 'A' and 'B'. The thermal conductivity of 'A' is twice of that of material 'B', while the thickness of layer of 'A' is half that of B. If the temperature ... drop (in °K) across the layer of material 'A' is (A) 125 (B) 133 (C) 150 (D) 160

Last Answer : (D) 160

A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted will (A) Increase (B) Decrease (C) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Description : A steam carrying pipeline is insulated with two layers of insulating materials with the inferior insulation material forming the inner part. If the two insulating layers are interchanged, the heat conducted ... ) Remain unaffected (D) May increase or decrease; depends on the thickness of each layer

Last Answer : Option C

Starting friction is low in case of the __________ lubrication. (A) Boundary (B) Hydrodynamic (C) Hydrostatic (D) Mixed/semi-fluid

Description : Starting friction is low in case of the __________ lubrication. (A) Boundary (B) Hydrodynamic (C) Hydrostatic (D) Mixed/semi-fluid

Last Answer : (C) Hydrostatic

When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is: (A) Free convection (B) Entry length problem in laminar forced conduction (developing thermal boundary layer) (C) Mixed convection (both free and forced) (D) Forced convection

Description : When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is: (A) Free convection (B) Entry length problem in laminar forced ... (developing thermal boundary layer) (C) Mixed convection (both free and forced) (D) Forced convection

Last Answer : (C) Mixed convection (both free and forced)

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

Which one the following is a correct statement? (A) The vertical section of the soil extending into the parent material, is called profile(B) The layers of the soil parallel to the earth surface are called horizons (C) The transitional layer between two adjoining horizons is called boundary (D) All of these

Description : Which one the following is a correct statement? (A) The vertical section of the soil extending into the parent material, is called profile (B) The layers of the soil parallel to the earth ... horizons (C) The transitional layer between two adjoining horizons is called boundary (D) All of these

Last Answer : Answer: Option D

Pick out the wrong statement. (A) The Reynolds analogy for mass transfer is given by Lewis relation and is applicable, when Schmidt number is one (B) Sherwood number for flow in pipes can be expressed as the ratio of the concentration gradient at wall to the overall concentration difference (C) According to film theory for equimolar counter diffusion, the mass transfer coefficient is given by DAB(B)P - 3, Q - 2 (D) The z-component of the total mass flux of a component A in binary mixture of A and B is given by - Dab'.dCA/dz

Description : Pick out the wrong statement. (A) The Reynolds analogy for mass transfer is given by Lewis relation and is applicable, when Schmidt number is one (B) Sherwood number for flow in pipes can be expressed ... flux of a component A in binary mixture of A and B is given by - Dab'.dCA/dz

Last Answer : (C) According to film theory for equimolar counter diffusion, the mass transfer coefficient is given by DAB(B)P - 3, Q - 2

With regard to the cornea: a. photokeratitis occurs with wavelength of 270nm b. microvilli are found in the outer layer of the epithelium c. the turnover of the corneal epithelium typically takes 30 days d. the corneal epithelium is about 10 layers in thickness

Description : With regard to the cornea: a. photokeratitis occurs with wavelength of 270nm b. microvilli are found in the outer layer of the epithelium c. the turnover of the corneal epithelium typically takes 30 days d. the corneal epithelium is about 10 layers in thickness

Last Answer : photokeratitis occurs with wavelength of 270nm

Fluid motion in the natural convection heat transfer between a solid surface and a fluid in contact with it, results from the (A) Existence of thermal boundary layer (B) Temperature gradient produced due to density difference (C) Buoyancy of the bubbles produced at active nucleation site (D) None of these

Description : Fluid motion in the natural convection heat transfer between a solid surface and a fluid in contact with it, results from the (A) Existence of thermal boundary layer (B) Temperature gradient produced ... difference (C) Buoyancy of the bubbles produced at active nucleation site (D) None of these

Last Answer : (D) None of these

Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Last Answer : (C) 70

Boundary lubricated bearing is (A) Thick film bearing (B) Thin film bearing (C) Hydrodynamic bearing (D) Hydrostatic bearing

Description : Boundary lubricated bearing is (A) Thick film bearing (B) Thin film bearing (C) Hydrodynamic bearing (D) Hydrostatic bearing

Last Answer : (B) Thin film bearing

A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Last Answer : (B) 0.1

Dittus-Boelter equation cannot be used for molten metals mainly due to its very low (A) Prandtl number (B) Grashoff number (C) Thermal conductivity (D) Viscosity

Description : Dittus-Boelter equation cannot be used for molten metals mainly due to its very low (A) Prandtl number (B) Grashoff number (C) Thermal conductivity (D) Viscosity

Last Answer : (A) Prandtl number

The ratio of kinematic viscosity to thermal diffusivity is called the __________ number. (A) Peclet (B) Prandtl (C) Stanton (D) Nusselt

Description : The ratio of kinematic viscosity to thermal diffusivity is called the __________ number. (A) Peclet (B) Prandtl (C) Stanton (D) Nusselt

Last Answer : (B) Prandtl