Current through each resistor when they are connected in series is A. different B. same C. can be both A and B D. decreasing

Current through each resistor when they are connected in series is

A. different

B. same

C. can be both A and B

D. decreasing
by

1 Answer

Answer :

same


by

Related questions

A capacitor and a coil are connected in series. The capacitor is charged and allowed to discharge through the coil. The current that will then flow through the capacitor-coil combination will do one of the following things. Will it: w) flow in one direction, beginning at a maximum and decreasing rapidly to zero x) oscillate indefinitely y) oscillate but diminish steadily to zero z) oscillate at high frequency at first but then at slower frequency

Description : A capacitor and a coil are connected in series. The capacitor is charged and allowed to discharge through the coil. The current that will then flow through the capacitor-coil combination will do ... but diminish steadily to zero z) oscillate at high frequency at first but then at slower frequency  

Last Answer : ANSWER: Y -- OSCILLATE BUT DIMINISH STEADILY TO ZERO

To limit current in LED, resistor should be connected in A. parallel B. series C. evacuated flask D. ionized tube

Description : To limit current in LED, resistor should be connected in A. parallel B. series C. evacuated flask D. ionized tube

Last Answer : series

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

A 10 ohm and a 20 ohm resistor are connected in parallel to a current source. What fraction of the current flows through the 20 ohm resistor? w) 1/2 x) 1/3 y) 2/3 z) 3/4

Description : A 10 ohm and a 20 ohm resistor are connected in parallel to a current source. What fraction of the current flows through the 20 ohm resistor? w) 1/2 x) 1/3 y) 2/3 z) 3/4

Last Answer : ANSWER: X -- 1/3

Three resistors which have different values are connected in series. Which one of the following statements is correct? w) The potential drop across all three resistors is the same. x) The same current passes through all three resistors. y) The same power is dissipated by all three resistors.

Description : Three resistors which have different values are connected in series. Which one of the following statements is correct? w) The potential drop across all three resistors is the same. x) The same current passes through all three resistors. y) The same power is dissipated by all three resistors. 

Last Answer : ANSWER: X -- THE SAME CURRENT PASSES THROUGH ALL THREE RESISTORS. 

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Three identical, each of emf 2 V and internal resistance `0.2 Omega` are connected in series to an external resistor of `7.4 Omega`. Calculate the cur

Description : Three identical, each of emf 2 V and internal resistance `0.2 Omega` are connected in series to an external resistor of `7.4 Omega`. Calculate the cur

Last Answer : Three identical, each of emf 2 V and internal resistance `0.2 Omega` are connected in series to ... 7.4 Omega`. Calculate the current in the circuit.

A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Description : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega` each. The equivalent resistance is `7 Omega`. Find

Last Answer : A `5 Omega` resistor is connected in series with a parallel combination of n resistors of `6 Omega ... The equivalent resistance is `7 Omega`. Find n.

Sir , if there are 9 LEDs connected in series with the 9 volt battery and each led has a forward voltage drop of 1 volt , do i need a resistor in the circuit (in series with led)?

Description : 9 leds each of 1 volt drop is series with 9  volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !

Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.

A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Last Answer : ANSWER: Z -- 5 V/R

A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Description : A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Last Answer : ANSWER: Z -- 3 AMPERES

Decreasing the value of the shunt resistor of an ammeter, it current measuring capability

Description : Decreasing the value of the shunt resistor of an ammeter, it current measuring capability

Last Answer : increases

A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.

Four amperes of current are measured through a 24 ohms resistor connected across a voltage

Description : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

Last Answer : Four amperes of current are measured through a 24 ohms resistor connected across a voltage source. How much voltage does the source produce? A.960 V B.9.6 V C.96 V D.8 V

`6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Description : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and `6 Omega` resistor. What is

Last Answer : `6Omega` and `12Omega` resistors are connected in parallel. This combination is connected in series with 10 V battery and ... 4 V B. 16 V C. 2 D. 8 V

Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Description : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by the `6 Omega` resistor is

Last Answer : Two resistors of `6 Omega " and " 9 Omega` are connected in series to a 120 V source. The power consumed by ... 384 W B. 616 W C. 1500 W D. 1800 W

Copper and carbon wires are connected in series and the combined resistor is kept at `0^(@)C`. Assuming the combined resistance does not vary with tem

Description : Copper and carbon wires are connected in series and the combined resistor is kept at `0^(@)C`. Assuming the combined resistance does not vary with tem

Last Answer : Copper and carbon wires are connected in series and the combined resistor is kept at `0^(@)C`. Assuming the combined ... C)` A. 4 B. 8 C. 6 D. 2

The equivalent resistance of two resistor connected in series is `6 Omega` and their equivalent resistance is `(4)/(3)Omega`. What are the values of r

Description : The equivalent resistance of two resistor connected in series is `6 Omega` and their equivalent resistance is `(4)/(3)Omega`. What are the values of r

Last Answer : The equivalent resistance of two resistor connected in series is `6 Omega` and their equivalent resistance is `(4 ... , 2 Omega` D. `6 Omega, 2 Omega`

A 2 V battery, a `990Omega` resistor and a potentiometer of 2 m length, all are connected in series of the resistance of potentiometer wire is `10Omeg

Description : A 2 V battery, a `990Omega` resistor and a potentiometer of 2 m length, all are connected in series of the resistance of potentiometer wire is `10Omeg

Last Answer : A 2 V battery, a `990Omega` resistor and a potentiometer of 2 m length, all are connected in series of the resistance ... 0.01Vm^(-1)` D. `0.1Vm^(-1)`

What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Description : What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Last Answer : You need to provide values of resistor and inductor etc to find the phase angle.

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel C. the resistor banks are composed of individual series-connected units D. there are separate switches for the motor and the control

Description : Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel ... individual series-connected units D. there are separate switches for the motor and the control

Last Answer : Answer: B

Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor

Description : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

Last Answer : Two series resistors are connected to an ac source. If there are 7.5 V rms across one resistor and 4.2 V rms across the other, the peak source voltage is? A.16.54 V B.1.65 V C.10.60 V D.5.93 V

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

Average power dissipated in resistor if sinusoidal p.d of peak value 25 V is connected across a 20 Ω resistor isA. 15.6 WB. 15 WC. 16 WD. 17 W

Description : Average power dissipated in resistor if sinusoidal p.d of peak value 25 V is connected across a 20 Ω resistor is A. 15.6 W B. 15 W C. 16 W D. 17 W

Last Answer : 15.6 W

A five ohm and a ten ohm resistor are connected in parallel, what single resistance is "equivalent" to this combination?

Description : A five ohm and a ten ohm resistor are connected in parallel, what single resistance is "equivalent" to this combination? 

Last Answer : ANSWER: 3 AND 1/3 OHM

A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Last Answer : ANSWER: W -- 25 OHMS

Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Description : Two identical resistors are connected in parallel and consume 200 watts together. A third identical resistor is added in parallel. The total power consumed is: w) 100 watts x) 200 watts y) 300 watts z) 400 watts

Last Answer : ANSWER: Y -- 300 WATTS

The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to obtain required speeds B. divert shunt field current for speed control in both directions of operation C. limit armature current in hoist and 'series field' current in lower to obtain required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Last Answer : Answer: C

Three capacitors with different capacitances are connected in series. Which of the following statements is TRUE? w) All three of the capacitors have the same potential difference between their plates. x) The magnitude of the charge is the same on all of the capacitor plates. y) The capacitance of the system depends on the voltage applied across the three capacitors.

Description : Three capacitors with different capacitances are connected in series. Which of the following statements is TRUE? w) All three of the capacitors have the same potential difference between their plates. x ... y) The capacitance of the system depends on the voltage applied across the three capacitors.

Last Answer : ANSWER: X -- THE MAGNITUDE OF THE CHARGE IS THE SAME ON ALL OF THE CAPACITOR PLATES

A component that allows only unidirectional current to pass through it is A. resistor B. inductor C. transformer D. diode

Description : A component that allows only unidirectional current to pass through it is A. resistor B. inductor C. transformer D. diode

Last Answer : diode

A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Description : A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Last Answer : ANSWER: 250 WATTS

A current of 6 amperes flows through a 2 ohm resistor for 30 seconds. How many coulombs of charge have passed through the resistor?

Description : A current of 6 amperes flows through a 2 ohm resistor for 30 seconds. How many coulombs of charge have passed through the resistor? 

Last Answer : ANSWER: 180 COULOMBS

A current of 5 amps passes through a 10 ohm resistor. How many joules of energy will be generated by this resistor in 2 seconds?

Description : A current of 5 amps passes through a 10 ohm resistor. How many joules of energy will be generated by this resistor in 2 seconds? 

Last Answer : ANSWER: 500 JOULES

A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Description : A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Last Answer : ANSWER: Z -- 300 OHM RESISTOR IN PARALLEL

In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal from the resistor at the top of the speed sensing circuit card C. hall effect current to detect slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Last Answer : Answer: A

Three identical cells each of emf 2 V and unknown internal resistance are connected in parallel. This combination is connected to a `5 Omega` resistor

Description : Three identical cells each of emf 2 V and unknown internal resistance are connected in parallel. This combination is connected to a `5 Omega` resistor

Last Answer : Three identical cells each of emf 2 V and unknown internal resistance are connected in parallel. ... what is the internal resistance of each cell ?

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

Description : The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

Last Answer : Answer: B

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

If the capacitors are connected in parallel, then the potential difference across each capacitor is A. same B. different C. zero D. infinite

Description : If the capacitors are connected in parallel, then the potential difference across each capacitor is A. same B. different C. zero D. infinite

Last Answer : same

10 cells, each of internal resistance `0.5 Omega` and 1.2 V emf are connected (a) all in series and (b) all in paralle. Calculate the current sent in

Description : 10 cells, each of internal resistance `0.5 Omega` and 1.2 V emf are connected (a) all in series and (b) all in paralle. Calculate the current sent in

Last Answer : 10 cells, each of internal resistance `0.5 Omega` and 1.2 V emf are connected (a) all in ... each case through a wire of resistance `0.8 Omega`.

Four cells, each of emf E and internal resistance r, are connected in series across an external resistance reverse. Then, the current in the external

Description : Four cells, each of emf E and internal resistance r, are connected in series across an external resistance reverse. Then, the current in the external

Last Answer : Four cells, each of emf E and internal resistance r, are connected in series across an external resistance reverse. Then, ... (3r+R)` D. `(2E)/(3r+R)`

A copper wire of diameter 0.16 cm is connected in series to an aluminium wire of diameter 0.25 cm. A current of 10 A is passed through them. Find (i)

Description : A copper wire of diameter 0.16 cm is connected in series to an aluminium wire of diameter 0.25 cm. A current of 10 A is passed through them. Find (i)

Last Answer : A copper wire of diameter 0.16 cm is connected in series to an aluminium wire of diameter 0.25 cm. A ... of aluminium wire is `10^(29) m^(-3)`.

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

If a current of 1.5 A is maintained in a resistor of 10 2, then the energy dissipated in the resistor in 1 minute will be : (1) 15 W (2) 22.5 W (3) 135 W (4) 1350 W

Description : If a current of 1.5 A is maintained in a resistor of 10 2, then the energy dissipated in the resistor in 1 minute will be : (1) 15 W (2) 22.5 W (3) 135 W (4) 1350 W

Last Answer : (4) 1350 W Explanation: The potential difference or voltage, V, across two points is defined as the energy, E dissipated or transferred by a coulomb of charge 9, that moves through two points.

Ratio of voltages is inverse ratio of the A. transformer B. resistor C. iron core D. current

Description : Ratio of voltages is inverse ratio of the A. transformer B. resistor C. iron core D. current

Last Answer : current

In transformer, alternating current is induced inA. primary coilB. secondary coilC. iron coreD. resistor

Description : In transformer, alternating current is induced inA. primary coil B. secondary coil C. iron core D. resistor

Last Answer : primary coil

The potential difference across a 4 ohm resistor is 20 volts. What is the current in the resistor?

Description : The potential difference across a 4 ohm resistor is 20 volts. What is the current in the resistor?

Last Answer : ANSWER: 5 AMPS

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS