Adiabatic bulk modulus is equal to: A. Υ × P; where Υ: the ratio of the specific heat capacities of the gas, P: pressureB. PressureC. The ratio of the specific heat capacities of the gasD. Υ ⁄ P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure

Adiabatic bulk modulus is equal to: 

A. Υ × P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure

B. Pressure

C. The ratio of the specific heat capacities of the gas

D. Υ ⁄ P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure


by

1 Answer

Answer :

Υ × P; where Υ: the ratio of the specific heat capacities of the gas, P: pressur
by

Related questions

Isothermal bulk modulus is equal to A. Υ × P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure B. Pressure C. The ratio of the specific heat capacities of the gas D. Υ ⁄ P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure

Description : Isothermal bulk modulus is equal to A. Υ × P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure B. Pressure C. The ratio of the specific heat capacities of the gas D. Υ ⁄ P; where Υ: the ratio of the specific heat capacities of the gas, P: pressure

Last Answer : Pressure

When a gas or a liquid is subjected to an increased pressure, the substance contracts, the bulk strain is defined as A. final volume ⁄ original volume B. final pressure ⁄ original pressureC. change in volume ⁄ original volumeD. original volume ⁄ change in volume

Description : When a gas or a liquid is subjected to an increased pressure, the substance contracts, the bulk strain is defined as A. final volume ⁄ original volume B. final pressure ⁄ original pressure C. change in volume ⁄ original volume D. original volume ⁄ change in volume

Last Answer : change in volume ⁄ original volume

Boyle's law states that A. pressure of a gas is inversely proportional to its volume i.e. P × V = constant B. pressure of a gas is directly proportional to its volume i.e. P⁄V = constant C. pressure of a gas is inversely proportional to the square of its volume i.e. P × V² = constant D. pressure of a gas is directly proportional to the square of its volume i.e. P ⁄ V² = constant

Description : Boyle's law states that A. pressure of a gas is inversely proportional to its volume i.e. P V = constant B. pressure of a gas is directly proportional to its volume i.e. P⁄V = constant C. ... of a gas is directly proportional to the square of its volume i.e. P ⁄ V² = constant

Last Answer : pressure of a gas is inversely proportional to its volume i.e. P × V = constant

The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit conversion is 20%, then the exit temperature (in k) is (Data: Heat of reaction at 298 K = - 50000 kJ/ kmole of A reacted Heat capacities CPA = CPB = 100kJ/kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Last Answer : (C) 600

Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid

Description : Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid

Last Answer : Answer: Option C

Van der Waals derived an expression for the ‘pressure defect’, if the observed pressure is denoted as ‘p’ and volume is denoted as ‘V’, the gas pressure in the bulk of the gas is equal to: A. p + a/V; where a: constant for the particular gas B. p + a/(V²); where a: constant for the particular gas C. p + (a × V); where a: constant for the particular gas D. p + (a × V²); where a: constant for the particular gas

Description : Van der Waals derived an expression for the pressure defect', if the observed pressure is denoted as p' and volume is denoted as V', the gas pressure in the bulk of the gas is equal to: A. p + ... a: constant for the particular gas D. p + (a V²); where a: constant for the particular gas

Last Answer : p + a/(V²); where a: constant for the particular gas

Velocity of escape is equal to A. r × √(2g); where r: radius of Earth or any other planet for that matter, g: gravitational field strength B. g × √(2r); where r: radius of Earth or any other planet for that matter, g: gravitational field strength C. √(2g) ⁄ r; where r: radius of Earth or any other planet for that matter, g: gravitational field strength D. √(2gr); where r: radius of Earth or any other planet for that matter, g: gravitational field strength

Description : Velocity of escape is equal to A. r √(2g); where r: radius of Earth or any other planet for that matter, g: gravitational field strength B. g √(2r); where r: radius of ... (2gr); where r: radius of Earth or any other planet for that matter, g: gravitational field strength

Last Answer : √(2gr); where r: radius of Earth or any other planet for that matter, g: gravitational field strength

The work done in an adiabatic change in a particular gas depends upon changes in the __________ only. (A) Temperature (B) Specific heat (C) Volume (D) Pressure

Description : The work done in an adiabatic change in a particular gas depends upon changes in the __________ only. (A) Temperature (B) Specific heat (C) Volume (D) Pressure

Last Answer : (A) Temperature

If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good (A) E = 3K (1 - 2/m) (B) E = 2N (1 + 1/m) (C) (3/2)K (1 - 2/m) = N (1 + 1/m) (D) All the above

Description : If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of  the material, the following relationship holds good  (A) E = 3K (1 - 2/m)  (B) E = 2N (1 + 1/m)  (C) (3/2)K (1 - 2/m) = N (1 + 1/m)  (D) All the above 

Last Answer : (D) All the above 

For a given material, if E, C, K and m are Young's modulus, shearing modulus, bulk modulus and Poisson ratio, the following relation does not hold good (A) E = 9KC/3K + C (B) E = 2K (1 + 2/m) (C) E = 2C (1 + 1/m) (D) E = 3C (1 - 1/m)

Description : For a given material, if E, C, K and m are Young's modulus, shearing modulus, bulk modulus and Poisson ratio, the following relation does not hold good (A) E = 9KC/3K + C (B) E = 2K (1 + 2/m) (C) E = 2C (1 + 1/m) (D) E = 3C (1 - 1/m)

Last Answer : (C) E = 2C (1 + 1/m)

The ratio of stress to volumetric strain is called a) Shear Modulus b) Young’s Modulus c) Bulk Modulus d) Modulus of elasticity

Description : The ratio of stress to volumetric strain is called a) Shear Modulus b) Young’s Modulus c) Bulk Modulus d) Modulus of elasticity

Last Answer : c) Bulk Modulus

The ratio of shear stress to shear strain is a) Shear modulus b)Young’s Modulus c) Bulk Modulus d)None of above

Description : The ratio of shear stress to shear strain is a) Shear modulus b)Young’s Modulus c) Bulk Modulus d)None of above

Last Answer : b)Young’s Modulus

The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Description : The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio

Last Answer : (d) Poisson’s Ratio

The relationship between Young’s modulus (E), Bulk modulus (K) and Poisson’s ratio (μ) is given by a. E=2K(1-2μ) b. E=3K(1-2μ) c. E=2K(1-2μ) d. E=2K(1-3μ)

Description : The relationship between Young’s modulus (E), Bulk modulus (K) and Poisson’s ratio (μ) is given by a. E=2K(1-2μ) b. E=3K(1-2μ) c. E=2K(1-2μ) d. E=2K(1-3μ)

Last Answer : b. E=3K(1-2μ)

While Young's modulus ‘E’ relates to change in length and bulk modulus ‘K’ relates to change in volume, modulus of rigidity ‘G’ relates to change in: A. weight B. density C. shape D. temperature

Description : While Young's modulus ‘E’ relates to change in length and bulk modulus ‘K’ relates to change in volume, modulus of rigidity ‘G’ relates to change in: A. weight B. density C. shape D. temperature

Last Answer : . shape

The heat capacities for the ideal gas state depend upon the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The heat capacities for the ideal gas state depend upon the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

The bulk modulus of elasticity of a liquid (A) Is zero for incompressible liquid (B) Decreases with pressure (C) Is independent of temperature & pressure (D) Increases with pressure

Description : The bulk modulus of elasticity of a liquid (A) Is zero for incompressible liquid (B) Decreases with pressure (C) Is independent of temperature & pressure (D) Increases with pressure

Last Answer : (D) Increases with pressure

The strain energy due to volumetric strain (A) Is directly proportional to the volume (B) Is directly proportional to the square of exerted pressure (C) Is inversely proportional to Bulk modulus (D) All the above

Description : The strain energy due to volumetric strain  (A) Is directly proportional to the volume  (B) Is directly proportional to the square of exerted pressure  (C) Is inversely proportional to Bulk modulus  (D) All the above 

Last Answer : (D) All the above 

The dimensional formula of bulk modulus of elasticity is same as that of the (A) Pressure (B) Density (C) Force (D) None of these

Description : The dimensional formula of bulk modulus of elasticity is same as that of the (A) Pressure (B) Density (C) Force (D) None of these

Last Answer : Option A

Bulk modulus of a fluid __________ as the pressure increases. (A) Remain same (B) Decreases (C) Increases (D) None of these

Description : Bulk modulus of a fluid __________ as the pressure increases. (A) Remain same (B) Decreases (C) Increases (D) None of these

Last Answer : Answer: Option C

Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Description : Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Last Answer : Answer: Option B

The bulk modulus of elasticity (A) Has the dimensions of 1/pressure (B) Increases with pressure (C) Is large when fluid is more compressible (D) Is independent of pressure and viscosity

Description : The bulk modulus of elasticity (A) Has the dimensions of 1/pressure (B) Increases with pressure (C) Is large when fluid is more compressible (D) Is independent of pressure and viscosity

Last Answer : Answer: Option B

bulk modulus of elasticity with increase in pressure (A) Increases (B) Decreases (C) Remain constant (D) Increases first up to certain limit and then decreases

Description : bulk modulus of elasticity with increase in pressure (A) Increases (B) Decreases (C) Remain constant (D) Increases first up to certain limit and then decreases

Last Answer : Answer: Option A

or the same heat transfer area and the terminal conditions, the ratio of the capacities of a single effect evaporator to a triple effect evaporator is (A) 3 (B) 0.33 (C) 1 (D) 1.33

Description : or the same heat transfer area and the terminal conditions, the ratio of the capacities of a single effect evaporator to a triple effect evaporator is (A) 3 (B) 0.33 (C) 1 (D) 1.33

Last Answer : (C) 1

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Specific heat of a gas for a reversible adiabatic process is (A) Negative (B) Zero (C) Infinity (D) None of these

Description : Specific heat of a gas for a reversible adiabatic process is (A) Negative (B) Zero (C) Infinity (D) None of these

Last Answer : (B) Zero

Einstein's mass-energy relationship states that if the mass decreases by Δm, the energy released ΔE is given by A. ΔE = Δm × c, where "c" denotes the speed of light. B. ΔE = Δm × c², where "c" denotes the speed of light. C. ΔE = Δm ⁄ c, where "c" denotes the speed of light. D. ΔE = Δm ⁄ c², where "c" denotes the speed of light

Description : Einstein's mass-energy relationship states that if the mass decreases by Δm, the energy released ΔE is given by A. ΔE = Δm c, where "c" denotes the speed of light. B. ΔE = Δm c², where "c" ... where "c" denotes the speed of light. D. ΔE = Δm ⁄ c², where "c" denotes the speed of light

Last Answer : ΔE = Δm × c², where "c" denotes the speed of light.

According to the equation ‘r = (mv)⁄(Be)’, the faster moving particles A. move in smaller circle B. move straight C. move in bigger circle D. move randomly

Description : According to the equation ‘r = (mv)⁄(Be)’, the faster moving particles A. move in smaller circle B. move straight C. move in bigger circle D. move randomly

Last Answer : move in bigger circle

Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type (A) Parallel flow with equal heat capacities (B) Counter flow with equal heat capacities (C) Counter flow with unequal heat capacities (D) Parallel flow with unequal heat capacities

Description : Parallel straight line pattern of temperature distribution for both hot and cold fluids is observed in case of heat exchanger of the type (A) Parallel flow with equal heat capacities (B) Counter ... (C) Counter flow with unequal heat capacities (D) Parallel flow with unequal heat capacities

Last Answer : (B) Counter flow with equal heat capacities

Two transformers of identical voltages but different capacities are operated in parallel, for satisfactory load sharing: a) Impedances should be equal b) Per unit impedance must be equal c) per unit impedance and X/R ratio must be equal d) Impedance and X/R ratio must be equal

Description : Two transformers of identical voltages but different capacities are operated in parallel, for satisfactory load sharing: a) Impedances should be equal b) Per unit impedance must be equal c) per unit impedance and X/R ratio must be equal d) Impedance and X/R ratio must be equal

Last Answer : Ans: C

Universal gas constant is defined as equal to product of the molecular weight of the gas and  (a) specific heat at constant pressure  (b) specific heat at constant volume  (c) ratio of two specific heats  (d) gas constant  (e) unity.

Description : Universal gas constant is defined as equal to product of the molecular weight of the gas and  (a) specific heat at constant pressure  (b) specific heat at constant volume  (c) ratio of two specific heats  (d) gas constant  (e) unity.

Last Answer : Answer : d

Is a steady flow process at total constant pressure through a control volume for which there is no heat?  a. Adiabatic Saturation Process  b. Dew point  c. Adiabatic Ratio  d. None of the above

Description : Is a steady flow process at total constant pressure through a control volume for which there is no heat?  a. Adiabatic Saturation Process  b. Dew point  c. Adiabatic Ratio  d. None of the above

Last Answer : Adiabatic Saturation Process

Which of the following diagramInternal energy is equal to the heat absorbed in case of a/an __________ process. (A) Constant volume (B) Polytropic (C) Adiabatic (D) Constant pressure s does not represent an Otto cycle?

Description : Which of the following diagrams does not represent an Otto cyInternal energy is equal to the heat absorbed in case of a/an __________ process. (A) Constant volume (B) Polytropic (C) Adiabatic (D) Constant pressure cle?

Last Answer : (A) Constant volume

An adiabatic process is one in which  A.no heat enters or leaves the gas  B.the temperature of the gas changes  C.the change in internal energy is equal to the mechanical workdone  D.all of the above

Description : An adiabatic process is one in which  A.no heat enters or leaves the gas  B.the temperature of the gas changes  C.the change in internal energy is equal to the mechanical workdone  D.all of the above

Last Answer : Answer: D

Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

Description : Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

Last Answer : Distinguish between Young’s modulus, bulk modulus and modulus of rigidity.

The unit of bulk modulus of elasticity for a liquid in S.I. unit is (A) N (B) N/m (C) N/m2 (D) N/m3

Description : The unit of bulk modulus of elasticity for a liquid in S.I. unit is (A) N (B) N/m (C) N/m2 (D) N/m3

Last Answer : (C) N/m2

For an incompressible fluid, the bulk modulus of elasticity is (A) 5 kg/m3 (B) ∞ N/m2 (C) 1 N (D) 0 N/m

Description : For an incompressible fluid, the bulk modulus of elasticity is (A) 5 kg/m3 (B) ∞ N/m2 (C) 1 N (D) 0 N/m

Last Answer : (B) ∞ N/m2

The value of bulk modulus of a fluid is required to determine (A) Reynold's number (B) Froude's number (C) Mach number (D) Euler's number

Description : The value of bulk modulus of a fluid is required to determine (A) Reynold's number (B) Froude's number (C) Mach number (D) Euler's number

Last Answer : Answer: Option C

A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)

Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)

Last Answer : Answer: Option B

The relationship between Young’s modulus (E), Modulus of rigidity (C) and Bulk modulus (K) is given by a. E=9CK/(C+3K) b. E=9CK/(2C+3K) c. E=9CK/(3C+K) d. E=9CK/(C-3K)

Description : The relationship between Young’s modulus (E), Modulus of rigidity (C) and Bulk modulus (K) is given by a. E=9CK/(C+3K) b. E=9CK/(2C+3K) c. E=9CK/(3C+K) d. E=9CK/(C-3K)

Last Answer : a. E=9CK/(C+3K)

Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain

Description : Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain

Last Answer : d. Normal stress on each face of cube / Volumetric strain

State the relation between Young’s modulus and bulk modulus.

Description : State the relation between Young’s modulus and bulk modulus. 

Last Answer : E = 3K(1 - 2 µ ) Where, E= Young’s Modulus  K= Bulk Modulus  µ= Poisson’s Ratio

Define and explain Bulk Modulus.

Description : Define and explain Bulk Modulus.

Last Answer : Bulk Modulus : When a body is subjected to three mutually perpendicular like stresses of same intensity then the ratio of direct stress and the corresponding volumetric strain of the body is constant and is known as Bulk Modulus. It is denoted by K.

Define modulus of rigidity and bulk Modulus.

Description : Define modulus of rigidity and bulk Modulus.

Last Answer : Bulk Modulus (K): When a body is subjected to three mutually perpendicular like stresses of same intensity then the ratio of direct stress and the corresponding volumetric strain of the body is constant and is ... (G): It is ratio of shear stress to shear strain, is called as Modulus of Rigidity. 

Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Description : Claude process of gas liquefaction employs (A) Merely compression of gas beyond its critical pressure (B) Joule-Thomson expansion cooling (C) Heat exchange with colder stream (D) Adiabatic expansion against a piston or in a turbine

Last Answer : (D) Adiabatic expansion against a piston or in a turbine

Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Description : Linde process of gas liquefaction employs (A) Exchange of heat with colder stream (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion) (C) Adiabatic expansion against a piston or in a turbine (D) Merely compressing the gas beyond its critical pressure

Last Answer : (B) Adiabatic expansion through a throttle valve (Joule-Thomson expansion)

Joule-Thomson co-efficient is the ratio of (A) Pressure change to temperature change occuring during adiabatic compression of a gas (B) Pressure change to temperature change occuring during adiabatic throttling of a gas (C) Temperature change to pressure change occuring during adiabatic compression of a gas (D) Temperature change to pressure change occuring during adiabatic throttling of a gas

Description : Joule-Thomson co-efficient is the ratio of (A) Pressure change to temperature change occuring during adiabatic compression of a gas (B) Pressure change to temperature change occuring during adiabatic ... a gas (D) Temperature change to pressure change occuring during adiabatic throttling of a gas

Last Answer : (D) Temperature change to pressure change occuring during adiabatic throttling of a gas

Also called absolute humidity and specific humidity.  a. Related humidity  b. Humidity ratio  c. Dew point  d. Adiabatic ratio

Description : Also called absolute humidity and specific humidity.  a. Related humidity  b. Humidity ratio  c. Dew point  d. Adiabatic ratio

Last Answer : Humidity ratio

Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas) (A) √T (B) 1/√P (C) √y (D) 1/√ρ

Description : Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas) (A) √T (B) 1/√P (C) √y (D) 1/√ρ

Last Answer : (B) 1/√P