Description : The unit of bulk modulus of elasticity for a liquid in S.I. unit is (A) N (B) N/m (C) N/m2 (D) N/m3
Last Answer : (C) N/m2
Description : A liquid compressed in cylinder has a volume of 0.04 m3 at 50 kg/cm² and a volume of 0.039 m3 at 150 kg/cm². The bulk modulus of elasticity of liquid is (A) 400 kg/cm² (B) 4000 kg/cm² (C) (D)
Last Answer : Answer: Option B
Description : The bulk modulus of elasticity of a liquid (A) Is zero for incompressible liquid (B) Decreases with pressure (C) Is independent of temperature & pressure (D) Increases with pressure
Last Answer : (D) Increases with pressure
Description : A 30-m vertical column of fluid (density 1878 kg/m3 ) is located where g= 9.65 mps2 . Find the pressure at the base of the column. (Formula: pg= gρhg/k ) a. 543680 N/m2 b. 543.68 kPa (gauge) c. Both a & b d. None of the above
Last Answer : Both a & b
Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ
Last Answer : (A) 3.6 AVS.ρ
Description : If E, N, K and 1/m are modulus of elasticity, modulus of rigidity. Bulk modulus and Poisson ratio of the material, the following relationship holds good (A) E = 3K (1 - 2/m) (B) E = 2N (1 + 1/m) (C) (3/2)K (1 - 2/m) = N (1 + 1/m) (D) All the above
Last Answer : (D) All the above
Description : The bulk modulus of elasticity (A) Has the dimensions of 1/pressure (B) Increases with pressure (C) Is large when fluid is more compressible (D) Is independent of pressure and viscosity
Description : SI unit for the surface tension is ____. (1) kg/m2 (2) kg/m3 (3) N/m (4) kg/m
Last Answer : (3) N/m Explanation: Surface tension is measured in force per unit length. Its SI unit is Newton per meter.
Description : Molecular volume of any perfect gas at 600 x 103 N/m2 and 27°C will be (a) 4.17m3/kgmol (b) 400 m3/kg mol (c) 0.15 m3/kg mol (d) 41.7 m3/kg mol (e) 417m3/kgmol.
Last Answer : Answer : a
Description : What is the unit of relative density? (1) kg/m (2) kg/m2 (3) kg/m3 (4) It has no unit
Last Answer : It has no unit
Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these
Last Answer : (A) - 0.000909 m
Description : The dimensional formula of bulk modulus of elasticity is same as that of the (A) Pressure (B) Density (C) Force (D) None of these
Last Answer : Option A
Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm
Last Answer : (C) 3.125 cm
Description : Experiments were conducted to determine the flux of a species A in a stagnant medium across a gas-liquid interface. The overall mass transfer coefficient based on the liquid side for dilute systems for the above was estimated to be 4 ... -4 (C) 5.6 10 -3 (D) 8.5 10 -3
Last Answer : (B) 8.5 × 10 -4
Description : bulk modulus of elasticity with increase in pressure (A) Increases (B) Decreases (C) Remain constant (D) Increases first up to certain limit and then decreases
Last Answer : Answer: Option A
Description : The ratio of stress to volumetric strain is called a) Shear Modulus b) Young’s Modulus c) Bulk Modulus d) Modulus of elasticity
Last Answer : c) Bulk Modulus
Description : The ratio of lateral strain to linear strain is called (a) Modulus of Elasticity (b) Modulus of Rigidity (c) Bulk Modulus (d) Poisson’s Ratio
Last Answer : (d) Poisson’s Ratio
Description : Bulk modulus of elasticity is a. Tensile stress / Tensile strain b. Shear stress / Shear strain c. Tensile stress / Shear strain d. Normal stress on each face of cube / Volumetric strain
Last Answer : d. Normal stress on each face of cube / Volumetric strain
Description : A masonry dam (density = 20,000 N/m3 ) 6 m high, one metre wide at the top and 4 m wide at the base, has vertical water face. The minimum stress at the base of the dam when the reservoir is full, will be (A) 75 N/m2 (B) 750 N/m2 (C) 7500 N/m2 (D) 75000 N/m
Last Answer : (C) 7500 N/m
Description : The unit of surface tension is (A) N/m (B) N/m2 (C) N/m3 (D) N-m
Description : Unit of mass velocity is (A) kg/hr (B) kg/m2 . hr (C) kg/m2 (D) kg/m3 . hr
Last Answer : (B) kg/m2 . hr
Description : A cantilever shaft has a diameter of 6 cm and the length is 40cm, it has a disc of mass 125 kg at its free end. The Young’s modulus for the shaft material is 250 GN/m2. Calculate the static deflection in nm. a) 0.001 b) 0.083c) 1.022 d) 0.065
Last Answer : a) 0.001
Description : Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ
Last Answer : (A) 3.6 W.D.V.ρ
Description : Bulk density of pulverised coal may be about __________ kg/m3 . (A) 100 (B) 500 (C) 1000 (D) 1500
Last Answer : (B) 500
Description : The live load to be considered for an accessible roof, is (A) Nil (B) 75 kg/m3 (C) 150 kg/m2 (D) 200 kg/cm
Last Answer : Answer: Option C
Description : Which of the following has the highest modulus of elasticity (about 7 × 106 kg/cm2)? (A) High speed steel (B) Stainless steel (C) Tungsten carbide (D) Superalloys
Last Answer : (C) Tungsten carbide
Description : For a clay slope of height of 10 m, the stability number is 0.05, = 2.0 t/m3 , C = 2.5 t/m2 , the critical height of the slope of the soil, is (A) 4.0 m (B) 12.5 m (C) 25.0 m (D) 15.0 m
Last Answer : (C) 25.0 m
Description : For turbulent flow of an incompressible fluid through a pipe, the flow rate ‘Q’ is proportional to (Δ P)n, where ΔP is the pressure drop. The value of exponent 'n' is (A) 1 (B) 0 (C) < 1 (D) > 1
Last Answer : (C) < 1
Description : The bulk density of aggregates , is (a) kN/m3 (b) Kg/1tr (c) g/cm3 (d) All the above.
Last Answer : (b) Kg/1tr
Description : If Thiele modulus is __________, then the pore diffusion resistance in a catalyst may be considered as negligible. (A) 0 (B) ∞ (C) < 0.5 (D) > 0.5
Last Answer : (C) < 0.5
Description : The basic filtration equation is given as dt/dV = (µ/A ∆P). [(α .CV/A) + Rm], where, V is volume of the filtrate; A is the filtration area, a is specific cake resistance, μ is viscosity of ... produced? Neglect filter medium resistance, Rm; assume incompressible cake. (A) 10 (B) 20 (C) 25 (D) 30
Last Answer : (B) 20
Description : A rod 3 m long is heated from 10°C to 90°C. Find the expansion of rod. Take Young’s modulus = 1.0 x 10^5 MN/m2 and coefficient of thermal expansion = 0.000012 per degree centigrade. 1. 0.168 cm 2. 0.208 cm 3. 0.288 cm 4. 0.348 cm
Last Answer : 3. 0.288 cm
Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ
Last Answer : (A) 3.6 V.W.Dr.ρ
Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm
Last Answer : (D) 5 mm
Description : Bulk modulus of a fluid __________ as the pressure increases. (A) Remain same (B) Decreases (C) Increases (D) None of these
Description : Bulk modulus of a fluid is the ratio of (A) Shear stress to shear strain (B) Increase in volume to the viscosity of fluid (C) Increase in pressure to the volumetric strain (D) Critical velocity to the viscosity of fluid
Description : The value of bulk modulus of a fluid is required to determine (A) Reynold's number (B) Froude's number (C) Mach number (D) Euler's number
Description : The unit of dynamic viscosity in SI unit is (A) kg/m. sec (B) N/m2 (C) m2 /sec (D) m/N. sec
Last Answer : (A) kg/m. sec
Description : An odd shaped body weighing 7.5 kg and occupying 0.01 m3 volume will be completely submerged in a fluid having specific gravity of (A) 1 (B) 1.2 (C) 0.8 (D) 0.75
Last Answer : Answer: Option D
Description : The interfacial area per unit volume of dispersion, in a gas-liquid contactor, for fractional hold up of gas = 0.1 and gas bubble diameter = 0.5 mm is given by (in m2 /m3 ) (A) 500 (B) 1200 (C) 900 (D) 800
Last Answer : (A) 500
Description : In a non-flow reversible process for which p = (- 3V+ 15) x 105N/m2,V changes from 1 m to 2 m3. The work done will be about (a) 100 xlOO5 joules (b) lxlO5 joules (c) 10 xlO5 joules (d) 10 xlO5 kilo joules (e) 10xl04ki\ojoules.
Last Answer : Answer : c
Description : The effectiveness factor for large value of Thiele modulus [L√(K/D1 )] of a solid catalysed first order reaction is equal to (where, L = length of the reactor, cm, D1 = diffusion co-efficient, cm2 /second). (A) L √(K/D1 ) (B) 1/[L√(K/D1 )] (C) 1 (D) ∞
Last Answer : (B) 1/[L√(K/D1 )]
Description : A gas (density = 1.5 kg/m3 , viscosity = 2 10 -5 kg/m.s) flowing through a packed bed (particle size = 0.5 cm, porosity = 0.5) at a superficial velocity of 2 m/s causes a pressure drop of 8400 Pa/m. The ... flowing at 3 m/s will be (A) 8400 Pa/m (B) 12600 Pa/m (C) 18900 Pa/m (D) 16800 Pa/m
Last Answer : (B) 12600 Pa/m
Description : . A 0.5 m high bed made up of a 1 mm dia glass sphere (density 2500 kg/m3 ) is to be fluidised by water (density 1000 kg/m3 ). If at the point of incipient fluidisation, the bed voidage is 40%, the pressure drop across the bed is (A) 4.4 KPa (B) 2.94 KPa (C) 3.7 KPa (D) None of these
Last Answer : (A) 4.4 KPa
Description : The unit of Torque in SI units (a) kg-m (b) kg-cm (c) N-m (d) N/m2
Last Answer : (c) N-m
Description : Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2
Description : Modulus elasticity of steel is generally taken as [ A ] 2 x 105 N/mm2 [ B ] 2 x 106 N/mm2 [ C ] 2 x 106 N/mm2 [ D ] 2 x 105 N/mm2
Last Answer : [ A ] 2 x 105 N/mm2
Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK
Last Answer : [ B ] 5000 vfCK
Description : At equilibrium the concentration of water in vapour phase (C* ) in kg/m3 of air space and the amount of water (m) adsorbed per kg of dry silica gel are related by, C* = 0.0667m. To maintain dry conditions in a room ... which the temperature is maintained constant) is (A) 0.0 (B) 0.2 (C) 0.4 (D) 1.0
Last Answer : (C) 0.4