About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

About 2-3 hp, power per gallon of a thin liquid provides vigorous
agitation in an agitator. 'Power number' in agitation is given by
(A) P. gc
/n
3
. D2
. ρ
(B) P. gc
. ρ/µ
by

1 Answer

Answer :

(A) P. gc
/n
3
. D2
. ρ
by

Related questions

Each term of the Bernoulli's equation written in the form, (p/ρ) + (g/gc ). Z + (v 2 /2gc ) = constant, represents the total energy per unit (A) Mass (B) Volume (C) Specific weight (D) None of these

Description : Each term of the Bernoulli's equation written in the form, (p/ρ) + (g/gc ). Z + (v 2 /2gc ) = constant, represents the total energy per unit (A) Mass (B) Volume (C) Specific weight (D) None of these

Last Answer : (A) Mass

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

In frictional fluid flow, the quantity, (P/ρ) + (V 2 /2gc) + gz/gc) is (A) Constant along a streamline (B) Not constant along a streamline (C) Increased in the direction of flow (D) None of these

Description : In frictional fluid flow, the quantity, (P/ρ) + (V 2 /2gc) + gz/gc) is (A) Constant along a streamline (B) Not constant along a streamline (C) Increased in the direction of flow (D) None of these

Last Answer : (B) Not constant along a streamline

Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Description : Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Last Answer : (B) < 10

A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630

Last Answer : (A) 7

The most important receptor involved in cytotoxic drug induced vomiting is (a) Histamine H1 receptor (b) Serotonin 5-HT3 receptor (c) Dopamine D2 receptor (d) Opioid µ receptor

Description : The most important receptor involved in cytotoxic drug induced vomiting is (a) Histamine H1 receptor (b) Serotonin 5-HT3 receptor (c) Dopamine D2 receptor (d) Opioid µ receptor

Last Answer : Ans: B

Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls in rotation per second (rps) D = diameter of rolls, m). (A) 3.6 V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ

Last Answer : (A) 3.6 V.W.Dr.ρ

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above

Description : Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above

Last Answer : a.100-120 rpm

Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity(C) Surface tension(D) Density

Description : Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity (C) Surface tension (D) Density

Last Answer : (D) Density

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

A 600kg hammer of a pile driver is lilted 2m the pilling head. What is the change of potential energy? If the hammer is realest. What will be its velocity and the instant if it sticks the pilling?  a. 10,772 N-m and 5.26m/s  b. 13,200 N-m and 5.26m/s  c. 11,772 N-m and 6.26m/s  d. 11,77 2N-m and5.26m/s ∫PE = mgo(∫Z)/gc

Description : A 600kg hammer of a pile driver is lilted 2m the pilling head. What is the change of potential energy? If the hammer is realest. What will be its velocity and the instant if it sticks the pilling?  a. 10,772 N-m and 5.26m/s ...  c. 11,772 N-m and 6.26m/s  d. 11,77 2N-m and5.26m/s ∫PE = mgo(∫Z)/gc

Last Answer : 11,772 N-m and 6.26m/s

In DNA, when AGCT occurs, their association is as per which of the following pair? (a) AT-GC (b) AG-CT (c) AC-GT (d) All of these

Description : In DNA, when AGCT occurs, their association is as per which of the following pair? (a) AT-GC (b) AG-CT (c) AC-GT (d) All of these

Last Answer : (a) AT-GC

Schmidt number is given by(A) µ/ρDAB(B) Re × Pe(C) Sh × Pe(D) Re/Pe

Description : Schmidt number is given by (A) µ/ρDAB (B) Re × Pe (C) Sh × Pe (D) Re/Pe

Last Answer : (A) µ/ρDAB

Prandtl number is given by (A) CP µ/a (B) hD/k (C) CP µ/k (D) µ/h CP

Description : Prandtl number is given by (A) CP µ/a (B) hD/k (C) CP µ/k (D) µ/h CP

Last Answer : (C) CP µ/k

The energy equation, E + (p/ρ) + (V 2 /2g) + gZ = constant (E = internal energy/mass), is applicable to (A) Perfect gases only (B) Isothermal flow of gases (C) Adiabatic unsteady flow of gases (D) All compressible fluids

Description : The energy equation, E + (p/ρ) + (V 2 /2g) + gZ = constant (E = internal energy/mass), is applicable to (A) Perfect gases only (B) Isothermal flow of gases (C) Adiabatic unsteady flow of gases (D) All compressible fluids

Last Answer : (D) All compressible fluids

Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas) (A) √T (B) 1/√P (C) √y (D) 1/√ρ

Description : Velocity of a gas in sound is not proportional to (where, T = Absolute temperature of the gas. P = Absolute pressure of the gas. y = Ratio of specific heats (Cp/Cv) ρ = specific weight of the gas) (A) √T (B) 1/√P (C) √y (D) 1/√ρ

Last Answer : (B) 1/√P

18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Description : 18.The total extension of a taper rod of length ‘L’ and end diameters ‘D1’ and ‘D2’, subjected to a load (P), is given of a. 4PL/ΠE. D1D2 b. 3PL/ΠE. D1D2 c. 2PL/ΠE. D1D2 d. PL/ΠE.D1D2 Where E=Young’s modulus of elasticity

Last Answer : a. 4PL/ΠE. D1D2

Which of the following is not accomplished by agitation of liquids in agitators? (A) Dispersing gas in liquid (B) Blending of immiscible liquids (C) Dispersing immiscible liquid in form of emulsion (D) Suspending solid particles

Description : Which of the following is not accomplished by agitation of liquids in agitators? (A) Dispersing gas in liquid (B) Blending of immiscible liquids (C) Dispersing immiscible liquid in form of emulsion (D) Suspending solid particles

Last Answer : (B) Blending of immiscible liquids

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Oil as a cutting fluid result in a lower coefficient of friction. Reason (R): Oil forms a thin liquid film between the tool face and chip, and it provides 'hydrodynamic lubrication'. [IES- 2000] (a ... explanation of A (c) A is true but R is false (d) A is false but R is true

Last Answer : (c) A is true but R is false

Number of particles in a crushed solid sample is given by (where, m = mass of particles in a sample, Vp = volume of one particle, ρ= density of particles) (A) m/ρ . Vp (B) m . ρ/Vp (C) m . Vp /ρ (D) Vp /m . ρ

Description : Number of particles in a crushed solid sample is given by (where, m = mass of particles in a sample, Vp = volume of one particle, ρ= density of particles) (A) m/ρ . Vp (B) m . ρ/Vp (C) m . Vp /ρ (D) Vp /m . ρ

Last Answer : (A) m/ρ . Vp

Does one hour of vigorous exercise per week (vs none) extend life expectancy by more or less than one hour?

Description : Does one hour of vigorous exercise per week (vs none) extend life expectancy by more or less than one hour?

Last Answer : Much, much more.

Assume that the speed (v) of sound in air depends upon the pressure (P) and density (ρ) of air, then use dimensional analysis to obtain

Description : Assume that the speed (v) of sound in air depends upon the pressure (P) and density (ρ) of air, then use dimensional analysis to obtain

Last Answer : Assume that the speed (v) of sound in air depends upon the pressure (P) and density (ρ) ... analysis to obtain an expression for the speed of sound.

The specific surface of spherical particles is proportional to (where, Dp = diameter of particle). (A) D2 p (B) Dp (C) 1/Dp (D) 1/D2p

Description : The specific surface of spherical particles is proportional to (where, Dp = diameter of particle). (A) D2 p (B) Dp (C) 1/Dp (D) 1/D2p

Last Answer : (C) 1/Dp

Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ

Description : Capacity of flight conveyor in tons/hr is given by (where, W & D = width and depth of flight respectively in metre V = speed of the conveyor, metre/second ρ = bulk density of material, kg/m3 ) (A) 3.6 W.D.V.ρ (B) 3.6 W.D.V (C) 3.6 W.V.ρ (D) 3.6 D.V.ρ

Last Answer : (A) 3.6 W.D.V.ρ

The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Description : The capacity of a classifier in 'tons of solid/hr' is given by (where, A = cross-sectional area in m2 , V = rising velocity of fluid in m/sec, S = percentage of solids in the suspension by volume, ρ = density of solids in kg/m3 ) (A) 3.6 AVS.ρ (B) 3.6 A.V.ρ (C) 3.6 A.S. ρ (D) 3.6 AVS/ρ

Last Answer : (A) 3.6 AVS.ρ

The specific surface of spherical particles is given by (where D and ρ are diameter and density of particle). (A) 6/D.ρ(B) 2/D.ρ (C) 4/D.ρ (D) 12/D.ρ

Description : The specific surface of spherical particles is given by (where D and ρ are diameter and density of particle). (A) 6/D.ρ (B) 2/D.ρ (C) 4/D.ρ (D) 12/D.ρ

Last Answer : (A) 6/D.ρ

Fanning equation is given by (∆P/ρ) = 4f (L/D) (v 2 /2gc ). It is applicable to __________ region flow. (A) Transition (B) Laminar (C) Turbulent (D) Both (B) and (C)

Description : Fanning equation is given by (∆P/ρ) = 4f (L/D) (v 2 /2gc ). It is applicable to __________ region flow. (A) Transition (B) Laminar (C) Turbulent (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Constant physical agitation of the spray liquid during field operations can be minimised by adding a). Emulsifiers b). Coupling agents c). Surfactants d). Humicants

Description : Constant physical agitation of the spray liquid during field operations can be minimised by adding a). Emulsifiers b). Coupling agents c). Surfactants d). Humicants

Last Answer : a). Emulsifiers

What is Nusselt number? (A) CP . µ/k (B) hD/k (C) h. CP /µ (D) CP . µ/h

Description : What is Nusselt number? (A) CP . µ/k (B) hD/k (C) h. CP /µ (D) CP . µ/h

Last Answer : (B) hD/k

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A Power sprayer essentially consists of: a) Tank a) Agitator b) Pressure Gauge c) All of the above

Description : A Power sprayer essentially consists of: a) Tank a) Agitator b) Pressure Gauge c) All of the above

Last Answer : All of the above

Why is the GameCube commonly abbreviated as "GCN," as opposed to just "GC"?

Description : Why is the GameCube commonly abbreviated as "GCN," as opposed to just "GC"?

Last Answer : answer:Well it's abbreviated NGC, not GCN At least where I've seen it used. NGC - Nintendo Game Cube Now why do they say NGC instead of GC? I'm not sure, other than for clarification. There might ... that is abbreviated GC, whether it be a console or a game. Sorry I can't help anymore than that.

What is Gas Chromatography ( GC) ?

Description : What is Gas Chromatography ( GC) ?

Last Answer : : Gas chromatography ( GC) is a method of identifying and quantifying the components of a mixture. This is done on a commercial gas chromatograph instrument. In gas chromatography a carrier gas ... time and the peak area of the detector signal are used to identify and quantify different components.

What is Gas Chromatography ( GC) ?

Description : What is Gas Chromatography ( GC) ?

Last Answer : : Gas chromatography ( GC) is a method of identifying and quantifying the components of a mixture. This is done on a commercial gas chromatograph instrument. In gas chromatography a carrier gas ... time and the peak area of the detector signal are used to identify and quantify different components.

Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Description : Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Last Answer : (A) Mixing highly viscous pastes

The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge

Description : The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge

Last Answer : (A) Boundary mixer

Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator

Description : Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator

Last Answer : (B) Cone type agitator

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

Agitator is provided in a crystalliser for(A) Avoiding deposition on cooler surfaces(B) Formation of nuclei(C) Crystal growth(D) All (A), (B) and (C)

Description : Agitator is provided in a crystalliser for (A) Avoiding deposition on cooler surfaces (B) Formation of nuclei (C) Crystal growth (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In Joule's experiment, an insulated container contains 20 kg of waterinitially at 25°C. It is stirred by an agitator, which is made to turn by aslowly falling body weighing 40 kg through a height of 4 m. The process isrepeated 500 times. The acceleration due to gravity is 9.8 ms-2. Neglectingthe heat capacity of agitator, the temperature of water (in °C) is(A) 40.5(B) 34.4(C) 26.8(D) 25

Description : In Joule's experiment, an insulated container contains 20 kg of waterinitially at 25°C. It is stirred by an agitator, which is made to turn by a slowly falling body weighing 40 kg through a height of 4 m. The process is repeated ... temperature of water (in °C) is (A) 40.5 (B) 34.4 (C) 26.8 (D) 25

Last Answer : (B) 34.4

Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Description : Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Last Answer : (D) All geometrical, dynamic and kinematic similarity

A Newtonian fluid is that (A) Which follows Newton's law of motion (B) Which needs a minimum shear, before it starts deforming (C) For which shear & deformation are related as T = µ (∂u/∂y) (D) None of these

Description : A Newtonian fluid is that (A) Which follows Newton's law of motion (B) Which needs a minimum shear, before it starts deforming (C) For which shear & deformation are related as T = µ (∂u/∂y) (D) None of these

Last Answer : (C) For which shear & deformation are related as T = µ (∂u/∂y)

Joule-Thomson co-efficient is defined as (A) µ = (∂P/∂T)H (B) µ = (∂T/∂P)H (C) µ = (∂E/∂T)H (D) µ = (∂E/∂P)H

Description : Joule-Thomson co-efficient is defined as (A) µ = (∂P/∂T)H (B) µ = (∂T/∂P)H (C) µ = (∂E/∂T)H (D) µ = (∂E/∂P)H

Last Answer : (B) µ = (∂T/∂P)H

The tensile stress in the rim of the flywheel is given by, Where, ρ is mass density and v is linear velocity at the mean radius of the rim. (A) ρv2/2 (B) πρv2 (C) ρv2 (D) 2 ρv2

Description : The tensile stress in the rim of the flywheel is given by, Where, ρ is mass density and v is linear velocity at the mean radius of the rim. (A) ρv2/2 (B) πρv2 (C) ρv2 (D) 2 ρv2

Last Answer : (C) ρv2