Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Laminar flow region is said to exist during agitation of a liquid in an
agitator, when the value of Reynolds number is
(A) > 10
(B) < 10
(C) > 100
(D) < 100
by

1 Answer

Answer :

(B) < 10
by

Related questions

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

Description : About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

Last Answer : (A) P. gc /n 3 . D2 . ρ

Laminar flow of a Newtonian fluid ceases to exist, when the Reynolds number exceeds (A) 4000 (B) 2100 (C) 1500 (D) 3000

Description : Laminar flow of a Newtonian fluid ceases to exist, when the Reynolds number exceeds (A) 4000 (B) 2100 (C) 1500 (D) 3000

Last Answer : (B) 2100

The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is(A) 100(B) 10(C) 5(D) 1.

Description : The Reynolds number of the liquid was increased 100 fold for a laminar falling film used for gas-liquid contacting. Assuming penetrating theory is applicable, the fold increase in the mass transfer co-efficient (Kc ) for the same system is. (A) 100 (B) 10 (C) 5 (D) 1

Last Answer : (B) 10

Critical value of the __________ number governs the transition from laminar to turbulent flow in free convection heat transfer. (A) Grashoff (B) Reynolds (C) Both 'a' & 'b' (D) Prandtl & Grashoff

Description : Critical value of the __________ number governs the transition from laminar to turbulent flow in free convection heat transfer. (A) Grashoff (B) Reynolds (C) Both 'a' & 'b' (D) Prandtl & Grashoff

Last Answer : (D) Prandtl & Grashoff

When the pipe Reynold's number is 6000, the flow is generally (A) Viscous(B) Laminar(C) Turbulent(D) Transition

Description : When the pipe Reynold's number is 6000, the flow is generally (A) Viscous (B) Laminar (C) Turbulent (D) Transition

Last Answer : (C) Turbulent

In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of the laminar film (C) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Description : In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of ... ) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Last Answer : (B) When the roughness projections are much smaller than the thickness of the laminar film

Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Nusselt number is related to the Reynolds number (Re) in turbulent & laminar flow respectively as (A) Re0.5, Re0.8 (B) Re0.8, Re-0.5 (C) Re0.8, Re0.5 (D) Re-0.8, Re0.5

Description : Nusselt number is related to the Reynolds number (Re) in turbulent & laminar flow respectively as (A) Re0.5, Re0.8 (B) Re0.8, Re-0.5 (C) Re0.8, Re0.5 (D) Re-0.8, Re0.5

Last Answer : (C) Re0.8, Re0.5

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Experimental study of laminar fluid flow through a circular tube was conducted by(A) Reynolds(B) Hagen and Poiseuille(C) Pascal(D) Blake-Plummer

Description : Experimental study of laminar fluid flow through a circular tube was conducted by (A) Reynolds (B) Hagen and Poiseuille (C) Pascal (D) Blake-Plummer

Last Answer : (B) Hagen and Poiseuille

For pipes, laminar flow occurs when Reynolds number is (A) Less than 2000 (B) Between 2000 and 4000 (C) More than 4000 (D) Less than 4000

Description : For pipes, laminar flow occurs when Reynolds number is (A) Less than 2000 (B) Between 2000 and 4000 (C) More than 4000 (D) Less than 4000

Last Answer : Answer: Option A

Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of (A) Grashoff number (B) Grashoff number & Reynolds number (C) Reynolds number (D) Grashoff number & Prandtl number

Description : Transition from laminar to turbulent zone in free convection heat transfer is governed by the critical value of (A) Grashoff number (B) Grashoff number & Reynolds number (C) Reynolds number (D) Grashoff number & Prandtl number

Last Answer : Option D

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above

Description : Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above

Last Answer : a.100-120 rpm

Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity(C) Surface tension(D) Density

Description : Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity (C) Surface tension (D) Density

Last Answer : (D) Density

The value of critical Reynolds number for pipe flow is (A) 1,300(B) 10,000 (C) 100,000 (D) None of these

Description : The value of critical Reynolds number for pipe flow is (A) 1,300 (B) 10,000 (C) 100,000 (D) None of these

Last Answer : (A) 1,300

When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is: (A) Free convection (B) Entry length problem in laminar forced conduction (developing thermal boundary layer) (C) Mixed convection (both free and forced) (D) Forced convection

Description : When the ratio of the Grashoff number and to the square of Reynolds number is one, the dominant mechanism of heat transfer is: (A) Free convection (B) Entry length problem in laminar forced ... (developing thermal boundary layer) (C) Mixed convection (both free and forced) (D) Forced convection

Last Answer : (C) Mixed convection (both free and forced)

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

For the Stoke's law to be valid in the case of a falling sphere in a fluid, the (A) Reynolds number (based on sphere diameter) should be < 1 (B) Flow around the sphere should be in turbulent region (C) Sphere must be metallic (D) Fluid density should be constant

Description : For the Stoke's law to be valid in the case of a falling sphere in a fluid, the (A) Reynolds number (based on sphere diameter) should be < 1 (B) Flow around the sphere should be in turbulent region (C) Sphere must be metallic (D) Fluid density should be constant

Last Answer : (C) Sphere must be metallic

Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around (A) 2000 (B) 10(C) 100 (D) 1000 Answer:

Description : Reynolds number for flow of water at room temperature through 2 cm dia pipe at an average velocity of 5 cm/sec is around (A) 2000 (B) 10 (C) 100 (D) 1000 Answer:

Last Answer : (D) 1000

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

Maximum heat transfer rate is obtained in __________ flow. (A) Laminar (B) Turbulent (C) Creeping (D) Transition region

Description : Maximum heat transfer rate is obtained in __________ flow. (A) Laminar (B) Turbulent (C) Creeping (D) Transition region

Last Answer : (B) Turbulent

Fanning equation is given by (∆P/ρ) = 4f (L/D) (v 2 /2gc ). It is applicable to __________ region flow. (A) Transition (B) Laminar (C) Turbulent (D) Both (B) and (C)

Description : Fanning equation is given by (∆P/ρ) = 4f (L/D) (v 2 /2gc ). It is applicable to __________ region flow. (A) Transition (B) Laminar (C) Turbulent (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

The Graetz number is concerned with the (A) Mass transfer between a gas and a liquid (B) Absorption with chemical reaction (C) Heat transfer in turbulent flow (D) Heat transfer in laminar flow

Description : The Graetz number is concerned with the (A) Mass transfer between a gas and a liquid (B) Absorption with chemical reaction (C) Heat transfer in turbulent flow (D) Heat transfer in laminar flow

Last Answer : (D) Heat transfer in laminar flow

Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Description : Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Last Answer : (B) For fluids in turbulent flow

The time taken for gravity flow of a fixed volume of liquid (as in Redwood viscometer) is directly proportional to its (A) Absolute viscosity (B) Ratio of absolute viscosity to density (C) Density (D) Reynolds number

Description : The time taken for gravity flow of a fixed volume of liquid (as in Redwood viscometer) is directly proportional to its (A) Absolute viscosity (B) Ratio of absolute viscosity to density (C) Density (D) Reynolds number

Last Answer : (B) Ratio of absolute viscosity to density

Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Description : Reynolds number for water flow through a tube of I.D. 5 cm is 1500. If a liquid of 5 centipoise viscosity and 0.8 specific gravity flows in the same pipe at the same velocity, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Data insufficient to predict pressure drop

Last Answer : (A) Increase

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Description : Asymptotic conditions is reached, when for a fluid flowing in laminar flow through a long tube (A) Exit-fluid temperature > wall temperature (B) Exit fluid temperature < wall temperature (C) Exit fluid temperature = wall temperature (D) Graetz number > 100

Last Answer : (C) Exit fluid temperature = wall temperature

For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Description : For laminar flow of a shear thinning liquid in a pipe, if the volumetric flow rate is doubled, the pressure gradient will increase by a factor of (A) 2 (B) < 2 (C) > 2 (D) 1/2

Last Answer : (A) 2

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

For an ideal fluid flow, Reynolds number is (A) 2100 (B) 100 (C) 0 (D) ∞

Description : For an ideal fluid flow, Reynolds number is (A) 2100 (B) 100 (C) 0 (D) ∞

Last Answer : (D) ∞

When the flow parameters at any given instant remain same at every point, then flow is said to be (A) Quasi-static (B) Steady state (C) Laminar (D) Uniform

Description : When the flow parameters at any given instant remain same at every point, then flow is said to be (A) Quasi-static (B) Steady state (C) Laminar (D) Uniform

Last Answer : Answer: Option D

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Description : The loss of head due to viscosity for laminar flow in pipes is (where d = Diameter of pipe, l = Length of pipe, v w = Specific weight of the flowing liquid) (A) 4 (B) 8 (C) 16 (D) 32

Last Answer : Answer: Option D

The term "laminar flow" is most often associated with the description of: w) conduction of sound by waves x) current flow in transistors y) effects of viscosity of liquids z) passage of light rays through a liquid

Description : The term "laminar flow" is most often associated with the description of: w) conduction of sound by waves x) current flow in transistors y) effects of viscosity of liquids z) passage of light rays through a liquid

Last Answer : ANSWER: Y -- EFFECTS OF VISCOSITY OF LIQUIDS

Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Description : Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Last Answer : (D) Reynolds number for the flow involved is < 2100

As the velocity V and thus the Reynolds number of a flow past a sphere increases from very low value, the drag force for Re << 1 (A) Increases linearly with V (B) Decreases linearly with V (C) Decreases as V2 (D) None of these

Description : As the velocity V and thus the Reynolds number of a flow past a sphere increases from very low value, the drag force for Re

Last Answer : (A) Increases linearly with V

Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the first fluid, the pressure drop will (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Description : Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the ... (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Last Answer : (B) Decrease

Constant physical agitation of the spray liquid during field operations can be minimised by adding a). Emulsifiers b). Coupling agents c). Surfactants d). Humicants

Description : Constant physical agitation of the spray liquid during field operations can be minimised by adding a). Emulsifiers b). Coupling agents c). Surfactants d). Humicants

Last Answer : a). Emulsifiers

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

What is the ratio of total kinetic energy of fluid passing per second to the value obtained on the basis of average velocity (for laminar flow through a circular pipe)? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Description : What is the ratio of total kinetic energy of fluid passing per second to the value obtained on the basis of average velocity (for laminar flow through a circular pipe)? (A) 0.5 (B) 1 (C) 1.5 (D) 2

Last Answer : (D) 2

Which of the following is not accomplished by agitation of liquids in agitators? (A) Dispersing gas in liquid (B) Blending of immiscible liquids (C) Dispersing immiscible liquid in form of emulsion (D) Suspending solid particles

Description : Which of the following is not accomplished by agitation of liquids in agitators? (A) Dispersing gas in liquid (B) Blending of immiscible liquids (C) Dispersing immiscible liquid in form of emulsion (D) Suspending solid particles

Last Answer : (B) Blending of immiscible liquids

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

How did the agitation bring about the ‘real awakening of India’ as Gandhiji said later? -SST 10th

Description : How did the agitation bring about the ‘real awakening of India’ as Gandhiji said later? -SST 10th

Last Answer : The agitation brought about real awakening' through its programmes like the Swadeshi and Boycott Movements, involvement of masses in this movement, involving women and youth, popularising the concept ... draw a wedge between the two communities. The cry Vande-Mataram filled the air everywhere.