Description : In the case of steady state forced vibration at a resonance, the amplitude of vibration is A) Inversely proportional to damping coefficient B) Inversely proportional to damping ratio C) Inversely proportional to resonant frequency D) Directly proportional to resonant frequency
Last Answer : B) Inversely proportional to damping ratio
Description : Highest theoretical frequency that can be processed at a sampling rate without aliasing. A. Folding frequency B. Resonant frequency C. Natural frequency D. Critical frequency
Last Answer : A. Folding frequency
Description : What is the natural resonant frequency?
Last Answer : The frequency at which capacitive reactance is equal to inductive reactance.
Description : The effective depth of a singly reinforced rectangular beam is 300mm. the section is over-reinforced and the neutral axis is 120mm below the top. If the maximum stress attained by concrete is 5N/mn2 and the modular ratio ... in the steel will (a) 130N/mm2 (b) 135N/mm2 (c) 160N/mm2 (d) 180N/mm2
Last Answer : (b) 135N/mm2
Description : The two resonant frequency ratio (ω/ ω2) in a dynamic vibration absorber system for a mass ratio 0.2 are given by A) 0 ; 1.0 B) 0.801 ; 1.248 C) 0.458 ; 1.124 D) 0.642 ; 1.558
Last Answer : B) 0.801 ; 1.248
Description : A single degree of freedom spring-mass system is subjected to a harmonic force of constant amplitude. For an excitation frequency of √3k/m , the ratio of the amplitude of steady state response to the static deflection of the spring is __________ A. 0.2 B. 0.5 C. 0.8 D. None of the above
Last Answer : B. 0.5
Description : On oscilloscope screen for dynamic measurement, lissajous diagram is normally used to determine the __________ of the input signal. (A) Frequency (B) Amplitude (C) Damping (D) None of these
Last Answer : (A) Frequency
Description : In damped free vibrations, which parameters indicate vibrations? A) Natural frequency B) Rate of decay of amplitude C) Both a. and b. D) None of the above
Last Answer : C) Both a. and b.
Description : If frequency of excitation of a forced vibration system with negligible damping is very close to natural frequency of the system, then the system will A) Execute harmonic motion of large amplitude B) Beat with a very high peak amplitude C) Perform aperiodic motion D) None of the above
Last Answer : A) Execute harmonic motion of large amplitude
Description : If ωmax is the frequency at which the peak amplitude occurs and ωn is the natural frequency of the system then In a forced vibration system with damping, the higher the damping, A) More will be ... and ωmax is independent of damping in this system D) The difference between ωn and ωmax will be zero
Last Answer : A) More will be the difference between ωn and ωmax
Description : When the frequency of external exciting force is equal to the natural frequency of the vibration of the system A. The amplitude of vibration is zero B. The amplitude of vibration is significantly small C. The amplitude of vibration is very large D. The amplitude does not change
Last Answer : C. The amplitude of vibration is very large
Description : In damped free vibrations, which parameters indicate vibrations? a. Natural frequency b. Rate of decay of amplitude c. Both a. and b. d. None of the above
Last Answer : c. Both a. and b.
Description : An instrument has two strings. Both have the same length and are uniform. One of the strings is under twice as much tension as the other and also twice the mass of the other. Then which of ... d) Both strings vibrate with the same frequency and have the same wave-length and the same wave velocity.
Last Answer : Ans:(d)
Description : A resonant system has a fundamental frequency of 100 Hz. If the next higher frequency that gives a resonance are 300 Hz and 500 Hz, the system could be (a) A pip open at both ends (b) A pipe ... (c) A string vibrating between two fixed points (d) A pipe open at one end and closed at the other
Description : What is Resonant Frequency?
Last Answer : Answer: The frequency at which resonant peak occurs is called the resonant frequency. Resonance frequency explains about the speed of the transient response.
Description : Increasing the resonant frequency of an end-fed Marconi antenna can be done by A. adding a capacitor in series and reducing the physical length B. adding an inductor in series C. adding an inductor in series D. All of these
Last Answer : A. adding a capacitor in series and reducing the physical length
Description : The effect of adding parasitic elements of a Hertz dipole is to A. make the antenna more omnidirectional B. reduce its resonant frequency C. increase the antenna’s power gain D. All of these
Last Answer : C. increase the antenna’s power gain
Description : When a capacitor is connected in series with a Marconi antenna? A. Antenna open circuit stops transmission B. An inductor of equal value must be added C. No change occurs to antenna D. Antenna resonant frequency increases
Last Answer : D. Antenna resonant frequency increases
Description : What is the effect of adding a capacitor in series with an antenna? A. The antenna’s resonant frequency will increase B. The antenna’s resonant frequency will decrease C. The antenna will be physically 5% longer than its electrical length D. A capacitor is never added in series with an antenna
Last Answer : A. The antenna’s resonant frequency will increase
Description : If the length of an antenna is changed from 2.5 meters to 2.8 meters, its resonant frequency will A. increase B. depend on the velocity factor so the resonant frequency can either be increased or decreased C. will be unchanged D. decrease
Last Answer : D. decrease
Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.
Last Answer : C. its resonant frequency will be increased
Description : How is it possible to lower the resonant frequency of Hertz dipole antenna? A. By reducing the frequency at the transmitter B. By connecting a capacitor in series with the antenna C. By the connecting a resistor in series with the antenna D. By connecting an inductor in series with the antenna
Last Answer : D. By connecting an inductor in series with the antenna
Description : Determine the lower half-power frequency of a class-C amplifier having upper half-power frequency of 10.025 MHz, a resonant frequency 5 MHz and a circuit Q of 10. A. 1.0025 MHz B. 10.525 MHz C. 0.5 MHz D. 10 MHz
Last Answer : A. 1.0025 MHz
Description : Transmission lines when connected to antenna have A. capacitive load B. resistive load whose resistance is less than characteristics impedance C. resistive load at the resonant frequency D. resistive load whose resistance is greater than the characteristic impedance of the line
Last Answer : C. resistive load at the resonant frequency
Description : The resonant frequency of electron wobble can be changed by variation of what force?
Last Answer : The applied magnetic field.
Description : What two variables determine the primary frequency of a resonant cavity?
Last Answer : Size and shape of the cavity.
Description : How will an iris that has portions along both the "a" and "b" dimension walls act at the resonant frequency?
Last Answer : As a shunt resistance.
Description : If the inductor and capacitor values are increased, what happens to the resonant frequency?
Last Answer : Decreases.
Description : What is the impedance of a crystal at its resonant frequency when it is used in the series mode?
Last Answer : Minimum.
Description : What is the impedance of a crystal at its resonant frequency when it is used in the parallel mode?
Last Answer : Maximum
Description : What equipment uses a calibrated resonant circuit to measure frequency?
Last Answer : Wavemeter.
Description : How is the Resonant Peak (Mr), resonant frequency (ωr), and band width determined from Nichols chart?
Last Answer : i) The resonant peak is given by the value of ω contour which is tangent to G(j ω ii) The resonant frequency is given by the frequency of G(jω iii) The bandwidth is given by frequency corresponding to the intersection point of G(jω – 3dB M-contour.
Description : Define –Resonant frequency
Last Answer : The frequency at which resonant peak occurs is called resonant frequency.
Description : An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance
Last Answer : Solution: For RLC series circuit
Description : Derive an expression for resonant frequency of series RLC circuit.
Last Answer : At resonance frequency in RLC series circuit, we have inductive reactance is equal to capacitive reactance i.e. Where fr is the resonant frequency in RLC series circuit.
Description : In a series RLC circuit operating below the resonant frequency the current (a) I leads Vs (b) I lags Vs (c) I is in Phase with Vs (d) None of these
Last Answer : In a series RLC circuit operating below the resonant frequency the current I leads Vs
Description : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is _____kHz. (A) 50000 (B) 0.2 (C) 600 (D) 5
Last Answer : A tuned circuit has a Q of 100 at its resonant frequency of 500 kHz. Its bandwidth is 5 kHz.
Description : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is
Last Answer : A series R-L-C Circuit has a resonant frequency of 1000 Hz. If the values of R, L and C are doubled, the new resonant frequency is 500 Hz
Description : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - a) 225 MHz b) 1.06 MHz c) 10 KHz d) 10 MHz
Last Answer : The Q factor of a coil at resonant frequency 1.5 MHz of an RLC series circuit is 150. The Bandwidth is : - 10 KHz
Description : In a series RLC circuit that is operating above the resonant frequency, the current : - a) lags the applied voltage b) leads the applied voltage c) is in phase with the applied voltage d) is zero
Last Answer : In a series RLC circuit that is operating above the resonant frequency, the current : - lags the applied voltage
Description : A series RLC circuit has a resonant frequency of 1 KHz and a quality factor Q = 100. If each of the R,L and C is doubled from its original value, the new Q of the circuit is: (1) 25 (2) 50 (3) 100 (4) 200
Last Answer : A series RLC circuit has a resonant frequency of 1 KHz and a quality factor Q = 100. If each of the R,L and C is doubled from its original value, the new Q of the circuit is: 200.
Description : In a series L-C circuit at the resonant frequency the?
Last Answer : In a series L-C circuit at the resonant frequency the current is maximum.
Description : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of?
Last Answer : In R-L-C series resonant circuit magnitude of resonance frequency can be changed by changing the value of L or C.
Description : The maximum velocity of a body in SHM with amplitude of 150 mm and a frequency 2 vibrations/sec is equal to a.1.885 m/sec b.0.01885 m/sec c.0.1885 m/sec d.18.55 m/sec e.185.5 m/sec
Last Answer : a. 1.885 m/sec
Description : The maximum displacement of a vibrating body on either side of its central position is known as _______________. a)amplitude b)frequency c)time period d)hertz
Last Answer : a)amplitude
Description : A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly
Last Answer : A 4 GHz carrier is amplitude modulated by a low-pass signal of maximum cut off frequency 1 MHz. lf this signal is to be ideally sampled, the minimum sampling frequency should be nearly 4 Ghz
Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values
Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature
Description : The maximum adiabatic flame temperature is attained, when the fuel is burnt with (A) Theoretically required amount of air (B) More than theoretically required amount of air (C) Less than theoretically required amount of air (D) Theoretically required amount of oxygen
Last Answer : (D) Theoretically required amount of oxygen
Description : __________ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gasvapor mixture. (A) Dry bulb (B) Wet bulb (C) Dew point (D) None of these
Last Answer : (B) Wet bulb
Description : The temperature at the eutectic point of the system is the __________ temperature that can be attained in the system. (A) Lowest (B) Highest (C) Average (D) None of these
Last Answer : (A) Lowest