Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Which of the following is not a way of minimizing if not eliminating noise?
A. Use redundancy
B. Increase transmitted power
C. Reduce signaling rate
D. Increase channel bandwidth
by

1 Answer

Answer :

D. Increase channel bandwidth
by

Related questions

An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Description : An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Last Answer : C. Crossfire

Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Description : Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Last Answer : D. Quantizing level

Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Description : Sources of impulse noise induced in communication channels. A. Erroneous digital coding bit caused by an error on a transmission facility B. Transients due to relay operation C. Crosstalk from dc signaling systems D. All of these

Last Answer : D. All of these

The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Description : The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Last Answer : A. Noise density

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

Relational database schema normalization is NOT for: (A) reducing the number of joins required to satisfy a query. (B) eliminating uncontrolled redundancy of data stored in the database. (C) eliminating number of anomalies that could otherwise occur with inserts and deletes. (D) ensuring that functional dependencies are enforced.

Description : Relational database schema normalization is NOT for: (A) reducing the number of joins required to satisfy a query. (B) eliminating uncontrolled redundancy of data stored in the database. (C) ... could otherwise occur with inserts and deletes. (D) ensuring that functional dependencies are enforced. 

Last Answer : reducing the number of joins required to satisfy a query.

In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Description : In radio regulation, the first symbol in the designation of radio emission is ______. A. Bandwidth B. Nature of signal(s) modulation the main carrier C. Type of modulation of the main carrier D. Type of information to be transmitted

Last Answer : C. Type of modulation of the main carrier

The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Description : The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Last Answer : D. Type of information to be transmitted

The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Description : The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Last Answer : D. Type of modulation of the main carrier

What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Description : What is the primary advantage of DSBSC in AM? A. Reduce bandwidth over standard AM B. All of these C. It is simpler to transmit and receive than the standard AM D. No transmitter power is wasted in the carrier

Last Answer : D. No transmitter power is wasted in the carrier

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

Eliminating a wholesaler from a marketing channel A)will cut costs and lead to lower prices. B)may or may not lower prices and will not eliminate the functions performed by the wholesaler. C)will eliminate the functions performed by the wholesaler and will lower costs. D)will reduce channel conflict.

Description : Eliminating a wholesaler from a marketing channel A)will cut costs and lead to lower prices. B)may or may not lower prices and will not eliminate the functions performed by the wholesaler. ... eliminate the functions performed by the wholesaler and will lower costs. D)will reduce channel conflict.

Last Answer : B)may or may not lower prices and will not eliminate the functions performed by the wholesaler.

The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Description : The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Last Answer : D. All of the above

What is the noise voltage across a 300Ω input resistance to a TV set with a 6MHz bandwidth and temperature of 30˚C? A. 2.3 µV B. 3.8µV C. 5.5µV D. 5.4µV

Description : What is the noise voltage across a 300Ω input resistance to a TV set with a 6MHz bandwidth and temperature of 30˚C? A. 2.3 µV B. 3.8µV C. 5.5µV D. 5.4µV

Last Answer : C. 5.5µV

Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Description : Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Last Answer : B. narrowing the bandwidth

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Description : At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Last Answer : B. 1.3 µV

Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Description : Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Last Answer : C. 4.78 µV

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Description : A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Last Answer : D. FDMA

What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Description : What is the channel bandwidth of a standard analogue telephone system? A. 300-500 Hz B. 1200 kHz C. 100-300 Hz D. 300-3400 Hz

Last Answer : D. 300-3400 Hz

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Description : Who is responsible in the correctness and accuracy of transmitted information content over a data communication? A. The channel B. The transmitter and receiver C. The modem D. The bridge

Last Answer : B. The transmitter and receiver

ULV spraying is used for a) Minimizing drift b) Reduce application rate c) Aerial spraying d) Spot application

Description : ULV spraying is used for a) Minimizing drift b) Reduce application rate c) Aerial spraying d) Spot application

Last Answer : ans b

____________ is the out-of-band signaling between toll central offices (Bell System Standard) A. 2,000 Hz B. 800 Hz C. 3,835 Hz D. 3700 Hz

Description : ____________ is the out-of-band signaling between toll central offices (Bell System Standard) A. 2,000 Hz B. 800 Hz C. 3,835 Hz D. 3700 Hz

Last Answer : D. 3700 Hz

A quadrature signaling have ________ possible states. A. 16 B. 8 C. 32 D. 4

Description : A quadrature signaling have ________ possible states. A. 16 B. 8 C. 32 D. 4

Last Answer : D. 4

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa

Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Description : Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Last Answer : B. channel

What theorem sets a limit on the maximum capacity of a channel with a given noise level? A. Nyquist theorem B. Hartley law C. Shannon-Hartley theorem D. Shannon theorem

Description : What theorem sets a limit on the maximum capacity of a channel with a given noise level? A. Nyquist theorem B. Hartley law C. Shannon-Hartley theorem D. Shannon theorem

Last Answer : C. Shannon-Hartley theorem

______ sets the limit on the maximum capacity of a channel with a given noise level. A. Hartley theorem B. Shannon-hartley theorem C. Nyquist theorem D. Shannon theorem

Description : ______ sets the limit on the maximum capacity of a channel with a given noise level. A. Hartley theorem B. Shannon-hartley theorem C. Nyquist theorem D. Shannon theorem

Last Answer : B. Shannon-hartley theorem

________ sets a limit on the maximum capacity of a channel with a give noise level. A. Hartley theorem B. Shannon-Hartley theorem C. Nyquist theorem D. Shannon theorem

Description : ________ sets a limit on the maximum capacity of a channel with a give noise level. A. Hartley theorem B. Shannon-Hartley theorem C. Nyquist theorem D. Shannon theorem

Last Answer : B. Shannon-Hartley theorem

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

Tips for minimizing or reducing electronic noise?

Description : Tips for minimizing or reducing electronic noise?

Last Answer : Looks like your speakers are picking up some EMI. Try going to Radio Shack and pick up some of those magnetic cuffs to clip on to your speaker cables. They’re pretty cheap and should help out. :)

The transmitter technique adopted to reduce the noise effect of the preceding question is called A. noise masking B. anitnoise C. noise killing D. preemphasis

Description : The transmitter technique adopted to reduce the noise effect of the preceding question is called A. noise masking B. anitnoise C. noise killing D. preemphasis

Last Answer : D. preemphasis

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Description : Top loading is used in an antenna in order to increase its ___________. A. input capacitance B. beamwidth C. bandwidth D. effective height

Last Answer : D. effective height

Width of frequency band just enough to ensure the transmission of information at a required rate and quality required, and under a specified condition and class of emission. A. Occupied bandwidth B. Transmission bandwidth C. Necessary bandwidth D. Frequency bandwidth

Description : Width of frequency band just enough to ensure the transmission of information at a required rate and quality required, and under a specified condition and class of emission. A. Occupied bandwidth B. Transmission bandwidth C. Necessary bandwidth D. Frequency bandwidth

Last Answer : C. Necessary bandwidth

The width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under a specified condition and class of emission. A. Occupied bandwidth B. Reference frequency C. Necessary bandwidth D. Frequency tolerance bandwidth

Description : The width of the frequency band which is just sufficient to ensure the transmission of information at the rate and with the quality required under a specified condition and class of emission. A. Occupied bandwidth B. Reference frequency C. Necessary bandwidth D. Frequency tolerance bandwidth

Last Answer : C. Necessary bandwidth

Common channel signalling______________ (A) Uses the speech or data path for signaling. (B) Does not use the speech or data path for signaling. (C) Needs no additional transmission facilities. (D) Finds it difficult to handle signaling during speech.

Description : Common channel signalling______________ (A) Uses the speech or data path for signaling. (B) Does not use the speech or data path for signaling. (C) Needs no additional transmission facilities. (D) Finds it difficult to handle signaling during speech.

Last Answer : (C) Needs no additional transmission facilities.

Describe the various signalling techniques. Compare in-channel signalling with common channel signaling, which is more advantageous.

Description : Describe the various signalling techniques. Compare in-channel signalling with common channel signaling, which is more advantageous.

Last Answer : Signaling systems link the variety of switching systems, transmission systems and subscriber equipments in telecommunication network to enable the network to function as a whole. Three forms of signaling are ... for passing control signals for a group of trunks or information