Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF
(150 MHz) marine-band receiver?
A. In the ionosphere
B. In the receiver rear end
C. In the receiver front end
D. In the atmosphere
by

1 Answer

Answer :

C. In the receiver front end
by

Related questions

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Description : What causes image interference? A. Low gain B. High IF C. Poor front-end selectivity D. Low signal-to-noise ratio

Last Answer : C. Poor front-end selectivity

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

A radio frequency in the ultra high frequency band of the radio spectrum band. A. 235.50 MHz B. 450.50 MHz C. 150.50 GHz D. 0.31250 GHz

Description : A radio frequency in the ultra high frequency band of the radio spectrum band. A. 235.50 MHz B. 450.50 MHz C. 150.50 GHz D. 0.31250 GHz

Last Answer : D. 0.31250 GHz

Which of the following fall under the high frequency band of the radio spectrum? A. 8.2345 MHz B. 150.50 MHz C. 2.4555 MHz D. 35.535 MHz

Description : Which of the following fall under the high frequency band of the radio spectrum? A. 8.2345 MHz B. 150.50 MHz C. 2.4555 MHz D. 35.535 MHz

Last Answer : A. 8.2345 MHz

What is the frequency range of an aircraft’s Very High Frequency (VHF) communications? A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz) B. 108.000 MHz to 117.95 MHz C. 329.15 MHz to 335.00 MHz D. 2.0000 MHz to 29.999 MHz

Description : What is the frequency range of an aircraft’s Very High Frequency (VHF) communications? A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz) B. 108.000 MHz to 117.95 MHz C. 329.15 MHz to 335.00 MHz D. 2.0000 MHz to 29.999 MHz

Last Answer : A. 118.000 MHz to 136.975 MHz (worldwide up to 151.975 MHz)

The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Description : The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Last Answer : D. 300 – 3000 MHz

A radio communications link is to be established via the ionosphere. The maximum virtual height of the layer is 100 km at the midpoint of the path and the critical frequency is 2 MHz. The distance between stations is 600 km. determine the optimum working frequency? A. 6.32 MHz B. 2.1 MHz C. 5.4 MHz D. 1.8 MHz

Description : A radio communications link is to be established via the ionosphere. The maximum virtual height of the layer is 100 km at the midpoint of the path and the critical frequency is 2 MHz. The distance between stations is 600 ... optimum working frequency? A. 6.32 MHz B. 2.1 MHz C. 5.4 MHz D. 1.8 MHz

Last Answer : C. 5.4 MHz

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

What frequency band is referred to as the metric waves? A. VHF B. UHF C. HF D. SHF

Description : What frequency band is referred to as the metric waves? A. VHF B. UHF C. HF D. SHF

Last Answer : A. VHF

What is the metric subdivision of VHF band? A. Metric B. Millimetric C. Decimetric D. Centimetric

Description : What is the metric subdivision of VHF band? A. Metric B. Millimetric C. Decimetric D. Centimetric

Last Answer : A. Metric

Where does the AM broadcast band located in the spectrum band? A. HF band B. VHF band C. LF band D. MF band

Description : Where does the AM broadcast band located in the spectrum band? A. HF band B. VHF band C. LF band D. MF band

Last Answer : D. MF band

Which band does channel 14 of the television channel belong?A. High VHF band B. EHF band C. UHF band D. Low VHF band

Description : Which band does channel 14 of the television channel belong? A. High VHF band B. EHF band C. UHF band D. Low VHF band

Last Answer : C. UHF band

Channel 7 of the regular television channel belongs to which band? A. Low VHF band B. High VHF band C. Low UHF band D. High UHF band

Description : Channel 7 of the regular television channel belongs to which band? A. Low VHF band B. High VHF band C. Low UHF band D. High UHF band

Last Answer : B. High VHF band

TV channels 2, 4 and 5 are known as ________. A. Mid band UHF B. Low band UHF C. High band VHF D. Low band VHF

Description : TV channels 2, 4 and 5 are known as ________. A. Mid band UHF B. Low band UHF C. High band VHF D. Low band VHF

Last Answer : D. Low band VHF

Troposheric scatter uses the frequencies in the ________ band. A. VLF B. UHF C. VHF D. UF

Description : Troposheric scatter uses the frequencies in the ________ band. A. VLF B. UHF C. VHF D. UF

Last Answer : B. UHF

Which frequency band is the standard AM radio broadcast? A. HF B. UHF C. MF D. VHF

Description : Which frequency band is the standard AM radio broadcast? A. HF B. UHF C. MF D. VHF

Last Answer : C. MF

The rhombic antenna is primarily used for A. ground wave propagation B. space wave propagation C. ionosphere scatter propagation D. sky wave propagation

Description : The rhombic antenna is primarily used for A. ground wave propagation B. space wave propagation C. ionosphere scatter propagation D. sky wave propagation

Last Answer : D. sky wave propagation

What propagation condition is usually indicated when a VHF signal is received from a station over 500 miles away? A. D-layer absorption B. Faraday rotation C. Tropospheric ducting D. Moonbounce

Description : What propagation condition is usually indicated when a VHF signal is received from a station over 500 miles away? A. D-layer absorption B. Faraday rotation C. Tropospheric ducting D. Moonbounce

Last Answer : C. Tropospheric ducting

What propagation condition is usually indicated when a VHF signal is received from a station over 5000 miles away? A. Moonbounce B. D-layer absorption C. Tropospheric ducting D. Faraday rotation

Description : What propagation condition is usually indicated when a VHF signal is received from a station over 5000 miles away? A. Moonbounce B. D-layer absorption C. Tropospheric ducting D. Faraday rotation

Last Answer : C. Tropospheric ducting

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Last Answer : D. 99.7 MHz

When the elevation angle of a geostationary satellite is 23˚ and the transmitting frequency is 3840 MHz, what is the free space loss in dB? A. 196 dB B. 200 dB C. 150 dB D. 100 dB

Description : When the elevation angle of a geostationary satellite is 23˚ and the transmitting frequency is 3840 MHz, what is the free space loss in dB? A. 196 dB B. 200 dB C. 150 dB D. 100 dB

Last Answer : A. 196 dB

Atmospheric noise becomes less severe at frequencies A. above 30 MHz B. below 30 MHz C. above 3000 kHz D. below 3000kHz

Description : Atmospheric noise becomes less severe at frequencies A. above 30 MHz B. below 30 MHz C. above 3000 kHz D. below 3000kHz

Last Answer : A. above 30 MHz

Atmospheric noise or static is not a great problem A. at frequencies below 20 MHz B. at frequencies below 5 MHz C. at frequencies above 30 MHz D. at frequencies above 1 MHz

Description : Atmospheric noise or static is not a great problem A. at frequencies below 20 MHz B. at frequencies below 5 MHz C. at frequencies above 30 MHz D. at frequencies above 1 MHz

Last Answer : C. at frequencies above 30 MHz

Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Last Answer : C. 15 to 160 MHz

What noise is observable at frequencies in the range from about 8 MHz to somewhat 1.5 GHz? A. Industrial noise B. Atmospheric noise C. Space noise D. Shot noise

Description : What noise is observable at frequencies in the range from about 8 MHz to somewhat 1.5 GHz? A. Industrial noise B. Atmospheric noise C. Space noise D. Shot noise

Last Answer : C. Space noise

What noise type is observable between 8 MHz to somewhat above 1.43 GHz or up to 1.5 GHz? A. Solar noise B. Space noise C. Galactic noise D. Cosmic noise

Description : What noise type is observable between 8 MHz to somewhat above 1.43 GHz or up to 1.5 GHz? A. Solar noise B. Space noise C. Galactic noise D. Cosmic noise

Last Answer : B. Space noise

Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Description : Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Last Answer : B. 30 MHz

Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Last Answer : B. 15 to 160 Mhz

What causes the maximum usable frequency to vary? A. The temperature of the ionosphere B. The speed of the winds in the upper atmosphere C. The type of weather just below the ionosphere D. The amount of radiation received from the sun

Description : What causes the maximum usable frequency to vary? A. The temperature of the ionosphere B. The speed of the winds in the upper atmosphere C. The type of weather just below the ionosphere D. The amount of radiation received from the sun

Last Answer : D. The amount of radiation received from the sun

What is the typical bandwidth of a satellite band? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Description : What is the typical bandwidth of a satellite band? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Last Answer : D. 500 MHz

Most satellites operate in which frequency band? A. 30 to 300 MHz B. 300 MHz to 3 GHz C. 3 GHz to 30 GHz D. Above 300 GHz

Description : Most satellites operate in which frequency band? A. 30 to 300 MHz B. 300 MHz to 3 GHz C. 3 GHz to 30 GHz D. Above 300 GHz

Last Answer : C. 3 GHz to 30 GHz

The bandwidth of C-band satellite frequency band in U.S. A. 500 GHz B. 1000 GHz C. 1000 MHz D. 500 MHz

Description : The bandwidth of C-band satellite frequency band in U.S. A. 500 GHz B. 1000 GHz C. 1000 MHz D. 500 MHz

Last Answer : D. 500 MHz

What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Description : What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Last Answer : C. 2225 MHz

Which of the following systems uses frequency band 870-885 MHz as a transmit band of its base station? A. TACS B. NTT C. NMT D. AMPS

Description : Which of the following systems uses frequency band 870-885 MHz as a transmit band of its base station? A. TACS B. NTT C. NMT D. AMPS

Last Answer : B. NTT

What is the bandwidth available in the commercial C-band? A. 1000 MHz B. 36 MHz C. 250 MHz D. 500 MHz

Description : What is the bandwidth available in the commercial C-band? A. 1000 MHz B. 36 MHz C. 250 MHz D. 500 MHz

Last Answer : D. 500 MHz

What is the quardband between transponder channels in the commercial C-band for satellite communications? A. 6 MHz B. 36 MHz C. 4 MHz D. 2 MHz

Description : What is the quardband between transponder channels in the commercial C-band for satellite communications? A. 6 MHz B. 36 MHz C. 4 MHz D. 2 MHz

Last Answer : C. 4 MHz

Determine from the following radio frequency that falls under the very high frequency band of the radio spectrum. A. 345.00 MHz B. 144.50 MHz C. 235.50 MHz D. 450.00 MHz

Description : Determine from the following radio frequency that falls under the very high frequency band of the radio spectrum. A. 345.00 MHz B. 144.50 MHz C. 235.50 MHz D. 450.00 MHz

Last Answer : C. 235.50 MHz

The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Description : The extremely high frequency (EHF) band is in the radio spectrum range of _______. A. 30 to 300 kHz B. 30 to 300 GHz C. 3 to 30 MHz D. 3 to 30 GHz

Last Answer : B. 30 to 300 GHz

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Description : Three identical circuits having 10 dB signal noise-to-noise ratio each are connected in tandem with each other, what is the overall S/N? A. 5.23 dB B. 14.77dB C. 30 dB D. 40 dB

Last Answer : A. 5.23 dB

What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Description : What signal-to-noise ratio is required for satisfactory television reception? A. 10 dB B. 30 dB C. 40 dB D. 20 dB

Last Answer : C. 40 dB

What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Description : What is the quantization signal-to-noise ratio if an 8-bit PCM code is used? A. 40 dB B. 50 dB C. 60 dB D. 65 dB

Last Answer : B. 50 dB

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz