What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

What part or section of a TV receiver that separates the sound and video signals?
A. IF stage
B. Video amplifier
C. Video detector
D. Burst separator
by

1 Answer

Answer :

C. Video detector
by

Related questions

Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Description : Which of the following parts of the radio receiver represent the component that extracts the desire RF signal from the electromagnetic wave? A. AF amplifier B. Antenna C. Detector D. Crystal

Last Answer : B. Antenna

Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Description : Cross modulation on a receiver is eliminated at the A. RF stage B. mixer stage C. IF stage D. detector stage

Last Answer : D. detector stage

Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Description : Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Last Answer : D. Mixer

After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Description : After the IF stages have been aligned, the next stage to align in FM receiver is. A. local oscillator B. limiter stage C. RF amplifier D. mixer stage

Last Answer : A. local oscillator

What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Description : What consists the front-end circuit of a VHF TV superheterodyne receiver? A. Mixer, RF amplifier and AFC? B. RF amplifier, Band pass filter and mixer C. Local oscillator, mixer and RF amplifier D. Local oscillator, AGC and antenna

Last Answer : C. Local oscillator, mixer and RF amplifier

Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Description : Refers to one of the front end circuit of a VHF TV superheterodyne receiver which is usually a separate circuit coupled to the mixer. A. Antenna feed B. AGC C. RF amplifier D. Local oscillator

Last Answer : D. Local oscillator

What is a device that detects both vertically and horizontally polarized signals simultaneously? A. Orthomode transducer B. Crystal detector C. Optoisolator D. Isomode detector

Description : What is a device that detects both vertically and horizontally polarized signals simultaneously? A. Orthomode transducer B. Crystal detector C. Optoisolator D. Isomode detector

Last Answer : A. Orthomode transducer

Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Description : Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Last Answer : D. Mixer

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Description : What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Last Answer : B. The combination of two signals to produce sum and difference frequencies.

Receives and collects satellite signals form a broadcast satellite. A. LNB B. Yagi-Uda array C. Satellite receiver D. Satellite disk

Description : Receives and collects satellite signals form a broadcast satellite. A. LNB B. Yagi-Uda array C. Satellite receiver D. Satellite disk

Last Answer : D. Satellite disk

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

Which amplifier stage (the preamplifier or the postamplifier) is a dominant contributor of noise and significantly influences the sensitivity of the receiver?

Description : Which amplifier stage (the preamplifier or the postamplifier) is a dominant contributor of noise and significantly influences the sensitivity of the receiver?

Last Answer : The preamplifier.

Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel

Description : Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel

Last Answer : A. The audio section

What is video amplifier?

Description : What is video amplifier?

Last Answer : The video or wideband amplifiers are designed to provide a relatively flat gain versus frequency response characteristics for the range of frequencies required to transmit video information.

What type of modulation is used on voice and video signals? A. AM B. FM C. SSB D. QPSK

Description : What type of modulation is used on voice and video signals? A. AM B. FM C. SSB D. QPSK

Last Answer : B. FM

In a TV receiver the raster is normal but there is no sound and quality of picture is poor. The defective part is

Description : In a TV receiver the raster is normal but there is no sound and quality of picture is poor. The defective part is

Last Answer : AGC, video IF amplifier, RF amplifier

A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Description : A particular circuit that rids FM of noise A. Detector B. Discriminator C. Phase Shifter D. Limiter

Last Answer : D. Limiter

What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Description : What kind of effect is referred to a varying light producing a varying voltage output of a detector? A. Current effect B. Voltage effect C. Resistive effect D. Photovoltaic effect

Last Answer : D. Photovoltaic effect

A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Last Answer : A. Noise equivalent power

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Description : The most common device used as a light detector in fiber optic communications system. A. LED B. Darlington phototransistor C. APDs D. PIN diode

Last Answer : C. APDs

If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Last Answer : A. 14 ns

Combination of modulator, channel and detector. A. Transceiver B. Discrete channel C. T/R channel D. Transponder

Description : Combination of modulator, channel and detector. A. Transceiver B. Discrete channel C. T/R channel D. Transponder

Last Answer : B. Discrete channel

What are the problems associated with switch type phase detector?

Description : What are the problems associated with switch type phase detector?

Last Answer : 1.The output voltage Ve is proportional to the input signal amplitude.This is undesirable because it makes phase detector gain and loop gain dependent on the input signal amplitude. 2.The output is proportional to cosQ making it non linear.

What is a switch type phase detector?

Description : What is a switch type phase detector?

Last Answer : An electronic switch is opened and closed by signal coming from VCO and the input signal is chopped at a repetition rate determined by the VCO frequency.This type of phase detector is called a ... detector since the phase information for only one half of the input signal is detected and averaged.

Give the classification of phase detector:

Description : Give the classification of phase detector:

Last Answer : 1.Analog phase detector . 2.Digital phase detector

The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Last Answer : B. the source, the link and the receiver

Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector

Description : Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector 

Last Answer : Positive feedback is used in 1. Amplifier 2. Rectifier 3.Oscillator 4. Detector 

Which of the following is used as an optical receiver in fiber optics communications a. APD b. Tunnel diode c. Laser diode d. LED

Description : Which of the following is used as an optical receiver in fiber optics communications a. APD b. Tunnel diode c. Laser diode d. LED

Last Answer : a. APD

The signal path from satellite to earth-based receiver. A. Downlink signal B. Uplink signal C. Incident signal D. Reflected signal

Description : The signal path from satellite to earth-based receiver. A. Downlink signal B. Uplink signal C. Incident signal D. Reflected signal

Last Answer : A. Downlink signal

Which of the following is not a typical output from a GPS receiver? A. Latitude B. Speed C. Altitude D. Longitude

Description : Which of the following is not a typical output from a GPS receiver? A. Latitude B. Speed C. Altitude D. Longitude

Last Answer : B. Speed

What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Description : What is the delay time for satellite transmissions from earth transmitter to earth receiver? A. 0.5 s B. 1s C. 5 ms D. 0.25 s

Last Answer : A. 0.5 s

What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Description : What is the delay time for satellite transmission from earth transmitter to earth receiver? A. 0.5 s B. 1.0 s C. 5 ms D. 0.25 ms

Last Answer : A. 0.5 s

_________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Description : _________ detects the satellite signal relayed from the feed and converts it to an electric current, amplifies and lower its frequency. A. Horn antenna B. LNA C. Satellite receiver D. Satellite dish

Last Answer : B. LNA

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Description : Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Last Answer : A. microvolts

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K