What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

What is the mixing process?
A. Distortion caused by auroral propagation
B. The combination of two signals to produce sum and difference frequencies.
C. The elimination of noise in wideband receiver by phase differentiation
D. The elimination of noise in a wideband receiver by phase comparison
by

1 Answer

Answer :

B. The combination of two signals to produce sum and difference frequencies.
by

Related questions

When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Description : When no signal is being received, the loudspeaker is not entirely silent as a result of the presence of A. parasitic oscillations in some of the receiver stages. B. negative feedback in each stage. C. spurious frequencies as a result of improper neutralization. D. internal receiver noise.

Last Answer : D. internal receiver noise.

_________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Description : _________ is the random and unpredictable electric signals from natural causes, both internal and external to the system. A. Interference B. Attenuation C. Distortion D. Noise

Last Answer : D. Noise

What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Last Answer : D. To protect small signals in PCM from quantizing distortion

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Description : If the current ratios of the two or more elements must be held 5% and the phase angle to 3° the antenna is called a A. end fire array B. critical phased array C. broadband array D. wideband array

Last Answer : B. critical phased array

What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Description : What distortion is not caused by transmission line characteristics? A. Phase distortion B. Pulse shape distortion C. Spacing bias distortion D. Amplitude distortion

Last Answer : C. Spacing bias distortion

What phenomenon causes the radio-path horizon distance to exceed the geometric horizon? A. E-layer skip. B. D-layer skip. C. Auroral skip. D. Radio waves may be bent.

Description : What phenomenon causes the radio-path horizon distance to exceed the geometric horizon? A. E-layer skip. B. D-layer skip. C. Auroral skip. D. Radio waves may be bent.

Last Answer : D. Radio waves may be bent.

How can multiple earth stations share a satellite on the same frequencies? A. Frequency reuse B. Multiplexing C. Mixing D. Frequency hopping

Description : How can multiple earth stations share a satellite on the same frequencies? A. Frequency reuse B. Multiplexing C. Mixing D. Frequency hopping

Last Answer : A. Frequency reuse

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

What device measures the angle between two radio frequencies and also the direction of propagation of a wave? A. Densimeter B. Absorption wavemeter C. Goniometer D. Ergometer

Description : What device measures the angle between two radio frequencies and also the direction of propagation of a wave? A. Densimeter B. Absorption wavemeter C. Goniometer D. Ergometer

Last Answer : C. Goniometer

A dielectric waveguide for the propagation of electromagnetic energy at light frequencies a. Stripline b. Microstrip c. Laser beam d. Fiber optics

Description : A dielectric waveguide for the propagation of electromagnetic energy at light frequencies a. Stripline b. Microstrip c. Laser beam d. Fiber optics

Last Answer : d. Fiber optics

Which antenna is not a wideband? A. Discone B. Folded dipole C. Helical D. Marconi

Description : Which antenna is not a wideband? A. Discone B. Folded dipole C. Helical D. Marconi

Last Answer : D. Marconi

________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel

Description : ________ is a typeof transmission impairment in which the signal loses strength due to the different propagation speeds of each frequency that makes up the signal. A) Attenuation B) Distortion C) Noise D) Decibel

Last Answer : Distortion

Which of the following term best described the overload distortion? A. Peak limiting B. Quantization noise C. Granular noise D. Slope distortion

Description : Which of the following term best described the overload distortion? A. Peak limiting B. Quantization noise C. Granular noise D. Slope distortion

Last Answer : A. Peak limiting

The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Description : The random and unpredictable electric signal from natural causes, both internal and external to the system is know as ________. A. Distortion B. Noise C. Attenuation D. Interference

Last Answer : B. Noise

The ___________ filter attenuates signals but passes frequencies below and above that band. A. low pass B. band pass C. band stop D. high pass

Description : The ___________ filter attenuates signals but passes frequencies below and above that band. A. low pass B. band pass C. band stop D. high pass

Last Answer : C. band stop

Refers to a continuous tone generated in a local exchange terminal through a combination of two frequencies 350 Hz, and 440 Hz. A. Busy tone B. Call waiting tone C. Dial tone D. Standard tone

Description : Refers to a continuous tone generated in a local exchange terminal through a combination of two frequencies 350 Hz, and 440 Hz. A. Busy tone B. Call waiting tone C. Dial tone D. Standard tone

Last Answer : B. Call waiting tone

Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET

Description : Which of the following low noise transistors is commonly used at microwave frequencies? A. MOSFET B. GASFET C. MESFET D. JFET

Last Answer : C. MESFET

Which of the following types of noise becomes of great importance at frequencies? A. Shot noise B. Random noise C. Impulse noise D. Transit-time noise

Description : Which of the following types of noise becomes of great importance at frequencies? A. Shot noise B. Random noise C. Impulse noise D. Transit-time noise

Last Answer : D. Transit-time noise

Atmospheric noise becomes less severe at frequencies A. above 30 MHz B. below 30 MHz C. above 3000 kHz D. below 3000kHz

Description : Atmospheric noise becomes less severe at frequencies A. above 30 MHz B. below 30 MHz C. above 3000 kHz D. below 3000kHz

Last Answer : A. above 30 MHz

Atmospheric noise or static is not a great problem A. at frequencies below 20 MHz B. at frequencies below 5 MHz C. at frequencies above 30 MHz D. at frequencies above 1 MHz

Description : Atmospheric noise or static is not a great problem A. at frequencies below 20 MHz B. at frequencies below 5 MHz C. at frequencies above 30 MHz D. at frequencies above 1 MHz

Last Answer : C. at frequencies above 30 MHz

What noise is observable at frequencies in the range from about 8 MHz to somewhat 1.5 GHz? A. Industrial noise B. Atmospheric noise C. Space noise D. Shot noise

Description : What noise is observable at frequencies in the range from about 8 MHz to somewhat 1.5 GHz? A. Industrial noise B. Atmospheric noise C. Space noise D. Shot noise

Last Answer : C. Space noise

The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Description : The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Last Answer : D. 300 – 3000 MHz

Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Description : Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Last Answer : B. 30 MHz

Extra-terrestrial noise is observable at frequencies from A. 0 to 20 KHz B. Above 2 GHz C. 8 to 1.43 GHz D. 5 to 8 GHz

Description : Extra-terrestrial noise is observable at frequencies from A. 0 to 20 KHz B. Above 2 GHz C. 8 to 1.43 GHz D. 5 to 8 GHz

Last Answer : C. 8 to 1.43 GHz

One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Last Answer : A. noise is amplified with voice when an FDM system is used

What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Description : What part or section of a TV receiver that separates the sound and video signals? A. IF stage B. Video amplifier C. Video detector D. Burst separator

Last Answer : C. Video detector

Receives and collects satellite signals form a broadcast satellite. A. LNB B. Yagi-Uda array C. Satellite receiver D. Satellite disk

Description : Receives and collects satellite signals form a broadcast satellite. A. LNB B. Yagi-Uda array C. Satellite receiver D. Satellite disk

Last Answer : D. Satellite disk

______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Description : ______ is the first component of any MATV system to received broadcast signals. A. Receiver B. Antenna C. Filter D. Transmitter

Last Answer : B. Antenna

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Description : Which circuit contributes most of the noise in a receiver? A. IF amplifier B. Demodulator C. AF amplifier D. Mixer

Last Answer : D. Mixer

Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Description : Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Last Answer : A. microvolts

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150MHz) marine-band receiver? A. Man-made noise B. In the atmosphere C. In the receiver front end D. In the ionosphere

Last Answer : C. In the receiver front end

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Description : What limits the sensitivity of a receiver? A. The power supply of the receiver B. The power output of a transmitter C. The noise floor of the receiver D. The distance between the transmitter and receiver

Last Answer : C. The noise floor of the receiver

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Description : Referred to as the stage in the radio receiver that contributes most of the noise. A. IF amplifier B. Supply stage C. Speaker D. Mixer

Last Answer : D. Mixer

Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Description : Where is the noise generated that primarily determines the signal-to-noise ratio in a VHF (150 MHz) marine-band receiver? A. In the ionosphere B. In the receiver rear end C. In the receiver front end D. In the atmosphere

Last Answer : C. In the receiver front end

What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Description : What do you call the single booster installed on the antenna dish of satellite receiver? A. Low noise amplifier B. Single amplifier C. Noise amplifier D. Rectifier

Last Answer : A. Low noise amplifier

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Description : ________ dispersion is caused by the difference in the propagation times of light rays that take different paths down a fiber. a. Material dispersion b. Wavelength dispersion c. Modal dispersion d. Delay dispersion

Last Answer : c. Modal dispersion

Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Description : Stacking antenna elements A. increases sensitivity to weak signals B. will suppress odd harmonics C. decrease signal to noise ratio D. increases selectivity

Last Answer : A. increases sensitivity to weak signals

An advantage of optic fiber rejecting an induced noise signals from magnetic field or solar storms flux. A. Electric hazard B. Cross talk C. Immunity to noise D. Shielding

Description : An advantage of optic fiber rejecting an induced noise signals from magnetic field or solar storms flux. A. Electric hazard B. Cross talk C. Immunity to noise D. Shielding

Last Answer : C. Immunity to noise

_______ is more prevalent in analog signals that have steep slopes or whose amplitudes vary rapidly. A. Peak limiting B. Quantization noise C. Granular noise D. Slope overload

Description : _______ is more prevalent in analog signals that have steep slopes or whose amplitudes vary rapidly. A. Peak limiting B. Quantization noise C. Granular noise D. Slope overload

Last Answer : D. Slope overload