____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

____ system transmits frequency-division-multiplexed voice band signals over a coaxial
cable for distances up to 4000 miles.
A. T carrier
B. X carrier
C. L carrier
D. F carrier
by

1 Answer

Answer :

C. L carrier
by

Related questions

Analog signals can be ________by combining them with a carrier frequency (A) Carried (B) Transported (C) Multiplexed (D) Mixed

Description : Analog signals can be ________by combining them with a carrier frequency (A) Carried (B) Transported (C) Multiplexed (D) Mixed

Last Answer : (C) Multiplexed

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

Which one of the following statements is correct regarding the GPS satellites? (A) The nominal altitude is about 20,200 km (B) The inclination of axis satellite is 55° (C) The satellite transmits two L band signals (L1 with 1575.42 MHz and L2 with 1276.6 MHz) (D) All of these

Description : Which one of the following statements is correct regarding the GPS satellites? (A) The nominal altitude is about 20,200 km (B) The inclination of axis satellite is 55° (C) The satellite transmits two L band signals (L1 with 1575.42 MHz and L2 with 1276.6 MHz) (D) All of these

Last Answer : Answer: Option D

What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Description : What carrier system multiplexes 96 voice band channels into a single 6.312 Mbps data signal? A. T1 carrier system B. T2 carrier system C. T1C carrier system D. T3 carrier system

Last Answer : B. T2 carrier system

Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Description : Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Last Answer : A. N-type connector

Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Description : Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Last Answer : B. F-type connector

Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector

Description : Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector

Last Answer : A. PL-259

What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4

Description : What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4

Last Answer : D. T4

Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Description : Crosstalk due to incomplete suppression of sidebands or to intermodulation of two or more frequency-multiplexed channels which is unintelligible is classified as A. Impulse noise B. Thermal noise C. Quantizing noise D. Miscellaneous noise

Last Answer : D. Miscellaneous noise

How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Description : How do you transmit through multiplexing, a thousand of voice channel information over a single fiber optic using on e wavelength? A. Polar division B. Time division C. Fiber division D. Frequency division

Last Answer : B. Time division

___ cable can carry signals ofhigher frequency ranges than_____ cable. A) Twisted-pair; fiber-optic B) Coaxial; fiber-optic C) Coaxial; twisted-pair D) none of the abov

Description : ___ cable can carry signals ofhigher frequency ranges than_____ cable. A) Twisted-pair; fiber-optic B) Coaxial; fiber-optic C) Coaxial; twisted-pair D) none of the abov

Last Answer : Coaxial; twisted-pair

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

For navigation as well as marine and aeronautical communications and radar, ____ band is used. A. L B. K C. S D. J

Description : For navigation as well as marine and aeronautical communications and radar, ____ band is used. A. L B. K C. S D. J

Last Answer : A. L

_________ uses thin coaxial cable. A) 10Base5 B) 10Base2 C) 10Base-T D) 10Base-F

Description : _________ uses thin coaxial cable. A) 10Base5 B) 10Base2 C) 10Base-T D) 10Base-F

Last Answer : 10Base2

______uses thick coaxial cable. A) 10Base5 B) 10Base2 C) 10Base-T D) 10Base-F

Description : ______uses thick coaxial cable. A) 10Base5 B) 10Base2 C) 10Base-T D) 10Base-F

Last Answer : 10Base5

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

A traditional cable TV network transmits signals ______. A) upstream B) downstream C) upstream and downstream D) none of the above

Description : A traditional cable TV network transmits signals ______. A) upstream B) downstream C) upstream and downstream D) none of the above

Last Answer : downstream

ECE Board Exam March 1996 The standard that specifies a balanced interface cable that will operate bit rates up to 10 Mbps with in a span distances up to 1200 m. A. RS-423A B. RS-422A C. RS-550A D. RS-449A

Description : ECE Board Exam March 1996 The standard that specifies a balanced interface cable that will operate bit rates up to 10 Mbps with in a span distances up to 1200 m. A. RS-423A B. RS-422A C. RS-550A D. RS-449A

Last Answer : B. RS-422A

What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Description : What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Last Answer : C. Quad

What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Description : What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Last Answer : A. Twisted pair

A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Description : A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Last Answer : D. 1 watt

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Last Answer : B. 0.66

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

Description : What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

Last Answer : C. 115.6 ns

What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Description : What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Last Answer : B.0.68

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Last Answer : C. 0.66

This type of transmission permits communication in the frequency range from 30 to 60 MHz and over distances from about 1000 to 2000 km. A. Troposcatter B. Ionospheric scatter C. Ducting D. Microwave

Description : This type of transmission permits communication in the frequency range from 30 to 60 MHz and over distances from about 1000 to 2000 km. A. Troposcatter B. Ionospheric scatter C. Ducting D. Microwave

Last Answer : B. Ionospheric scatter

Type of transmission path that permits communication in the frequency range from 30 to 60 MHz and over distances form about 1000 to 2000 km. A. Ducting B. Ionospheric scatter C. Microwave D. Troposcatter

Description : Type of transmission path that permits communication in the frequency range from 30 to 60 MHz and over distances form about 1000 to 2000 km. A. Ducting B. Ionospheric scatter C. Microwave D. Troposcatter

Last Answer : B. Ionospheric scatter

It is a system where the digital signals are placed directly on the coaxial cable.

Description : It is a system where the digital signals are placed directly on the coaxial cable.

Last Answer : Baseband

An FDM hierarchy which is formed by frequency – division multiplexing 10 super groups together for a combined capacity of 600 voice band message channels.

Description : An FDM hierarchy which is formed by frequency – division multiplexing 10 super groups together for a combined capacity of 600 voice band message channels.

Last Answer : Mastergroup

In radio signal emission designation, the fifth symbol means A. Details of signals B. Type of information transmitted C. Nature of multiplexing D. Nature of signal modulating the main carrier

Description : In radio signal emission designation, the fifth symbol means A. Details of signals B. Type of information transmitted C. Nature of multiplexing D. Nature of signal modulating the main carrier

Last Answer : C. Nature of multiplexing

The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Description : The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Last Answer : D. Type of information to be transmitted

The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Description : The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Last Answer : D. Type of modulation of the main carrier

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

Which of the following is referred to as a radio emission without sidebands A. Analog B. Carrier C. Data D. Voice

Description : Which of the following is referred to as a radio emission without sidebands A. Analog B. Carrier C. Data D. Voice

Last Answer : B. Carrier

______ cable is used for voice and data communications. A) Coaxial B) Fiber-optic C) Twisted-pair D) none of the above

Description : ______ cable is used for voice and data communications. A) Coaxial B) Fiber-optic C) Twisted-pair D) none of the above

Last Answer : Twisted-pair

……….cable is used for voice and data communications. a. Twisted-pair b. None of These c. Coaxial d. Fiber-optic

Description : ……….cable is used for voice and data communications. a. Twisted-pair b. None of These c. Coaxial d. Fiber-optic

Last Answer : a. Twisted-pair

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ______. a. 64 Kbps b. 32 Mbps c. 32 Kbps d. 64 MbpS

Last Answer : c. 32 Kbps

If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Description : If link transmits 4000 frames per second and each slot has 8 bits, the transmission rate of circuit of this TDM is ............... (A) 64 Kbps (B) 32 Mbps (C) 32 Kbps (D) 64 Mbps

Last Answer : (C) 32 Kbps

A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Description : A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Last Answer : C. Interpolator

What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A

Description : What is the first symbol of a radio signal transmission having an amplitude modulated signal carrier, double side band? A. C B. B C. H D. A

Last Answer : D. A

Which of the following refers to a double side band full carrier? A. A3E B. A3J C. F3 D. R3A

Description : Which of the following refers to a double side band full carrier? A. A3E B. A3J C. F3 D. R3A

Last Answer : A. A3E

The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Description : The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Last Answer : B. 120 kHz

Pulse – amplitude modulation signals are multiplexed by using

Description : Pulse – amplitude modulation signals are multiplexed by using

Last Answer : FET switches

Ten signals, each requiring 3000 Hz, are multiplexed on to a single channel using FDM. How much minimum bandwidth is required for the multiplexed channel ? Assume that the guard bands are 300 Hz wide. (A) 30,000 (B) 32,700 (C) 33,000 (D) None of the above

Description : Ten signals, each requiring 3000 Hz, are multiplexed on to a single channel using FDM. How much minimum bandwidth is required for the multiplexed channel ? Assume that the guard bands are 300 Hz wide. (A) 30,000 (B) 32,700 (C) 33,000 (D) None of the above

Last Answer : (B) 32,700

Which of hte following is considered a broad band communication channel? a. coaxial cable b. fiber optics cable c. microwave circuits d. all of above

Description : Which of hte following is considered a broad band communication channel? a. coaxial cable b. fiber optics cable c. microwave circuits d. all of above

Last Answer : all of above