What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3? A. 1.54 ns B. 11.5 ns C. 115.6 ns D. 1156 ns

What is the time delay introduced by a 75-ft coaxial cable with a dielectric constant of 2.3?
A. 1.54 ns
B. 11.5 ns
C. 115.6 ns
D. 1156 ns
by

1 Answer

Answer :

C. 115.6 ns
by

Related questions

What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Last Answer : C. 75 ns

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Last Answer : B. 0.66

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Last Answer : C. 0.66

What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Description : What is the velocity factor of coaxial cable with a characteristic impedance of 50Ω and capacitance of 30pF/ft and inductance of 75 nH/ft? A. 0.58 B.0.68 C. 0.98 D. 0.81

Last Answer : B.0.68

If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns

Last Answer : A. 14 ns

An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Description : An RG-11/U foam coaxial cable has a maximum voltage standing wave of 52 V and a minimum voltage of 17 V. Find the value of the resistive load. A. 24.59Ω B. Either A or C C. 228.75Ω D. Neither A nor C

Last Answer : B. Either A or C

What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Last Answer : A. 100Ω

If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Description : If a fiber optic system has a rise time of 38.55 ns, the source rise time is 12 ns and the detector rise time is 12 ns, what is the cable rise time? A. 34.61 ns B. 14.55 ns C. 52.55 ns D. 26.25 ns

Last Answer : A. 34.61 ns

A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Description : A coaxial cable has 7dB of reflected power when the input is 5 watts. What is the output of the transmission line? A. 5 watts B. 2.5 watts C. 1.25 watts D. 1 watt

Last Answer : D. 1 watt

What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Description : What do you call a cable consisting of twisted pairs of conductors, each separately insulated? A. Microstrip line B. Strip line C. Quad D. Coaxial cable

Last Answer : C. Quad

What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Description : What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Last Answer : A. Twisted pair

____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Description : ____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Last Answer : C. L carrier

Why is the physical length of a coaxial cable transmission line shorter than its electrical length?A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the coaxial cable C. The surge impedance is higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Description : Why is the physical length of a coaxial cable transmission line shorter than its electrical length? A. Skin effect is less pronounced in the coaxial cable B. RF energy moves slower along the ... higher in the parallel feed line D. The characteristic impedance is higher in the parallel feed line

Last Answer : B. RF energy moves slower along the coaxial cable

What is the meaning of the term “velocity factor” of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial cable. C. The velocity of the wave on the transmission line multiplied by the velocity of light in a vacuum. D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Description : What is the meaning of the term velocity factor of a transmission line? A. The ratio of the characteristic impedance of the line to the terminating impedance B. The index of shielding for coaxial ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum.

Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Description : Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Last Answer : A. N-type connector

Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Description : Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Last Answer : B. F-type connector

Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector

Description : Which of the following coaxial cable connectors is called the UHF connector? A. PL-259 B. BNC C. N-type connector D. F connector

Last Answer : A. PL-259

What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of light in vacuum C. The ratio of the characteristic impedance of the line to the terminating impedance D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Description : What is the meaning of the term velocity factor of a transmission line? A. The index of shielding for coaxial cable B. The velocity of the wave on the transmission line multiplied by the velocity of ... The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

Last Answer : D. The velocity of the wave on the transmission line divided by the velocity of light in a vacuum

ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Description : ECE Board Exam March 1996 It is a spacecraft placed in orbit around the earth carrying onboard microwave receiver and transmitting equipments. A. Fiber optic equipment B. Communications satellite C. Wireless radio system D. Coaxial cable syste

Last Answer : B. Communications satellite

Determine the gain of a 6 ft. parabolic dish operating at 1800 MHz. A. 30 dB B. 11.2 dB C. 15.5 dB D. 28.17 dB

Description : Determine the gain of a 6 ft. parabolic dish operating at 1800 MHz. A. 30 dB B. 11.2 dB C. 15.5 dB D. 28.17 dB

Last Answer : D. 28.17 dB

Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M’s locker number is 2 less than O’s lockers number. II. Lockers of N and P are next to each other. If N’s locker number is 52 then M’s locker number could be a) 52 or 53 only b) 53 or 54 only c) 54 or 55 only d) 53 or 55 only

Description : Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M's locker number is 2 less than O's lockers ... could be a) 52 or 53 only b) 53 or 54 only c) 54 or 55 only d) 53 or 55 only

Last Answer : c) 54 or 55 only

Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M’s locker number is 2 less than O’s lockers number. II. Lockers of N and P are next to each other. 14. If Q’s locker number is 54 and N’s locker number is greater than Q’s locker number, then which locker number is not allocated? a) locker 52 b) locker 53 c) locker 54 d)locker 56

Description : Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M's locker number is 2 less ... , then which locker number is not allocated? a) locker 52 b) locker 53 c) locker 54 d)locker 56

Last Answer : a) locker 52

Find the equivalent inductance per foot of the above cable? A. 13.5 nF/ft B. 13.5 pF/ft C. 116.8 nH/ft D. 116.8 pF/ft

Description : Find the equivalent inductance per foot of the above cable? A. 13.5 nF/ft B. 13.5 pF/ft C. 116.8 nH/ft D. 116.8 pF/ft

Last Answer : C. 116.8 nH/ft

What illumination factor is normally considered in computing parabolic antenna gain in microwave communications? A. 0.54 B. 0.65 C. 0.75 D. 0.85

Description : What illumination factor is normally considered in computing parabolic antenna gain in microwave communications? A. 0.54 B. 0.65 C. 0.75 D. 0.85

Last Answer : A. 0.54

A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Description : A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Last Answer : Ans: A 15 ns because in synchronous counter all the flip-flops change state at the same time.

Which of the cable length has the highest attenuation? a. 1 km b. 2 km c. 95 ft d. 5500 ft

Description : Which of the cable length has the highest attenuation? a. 1 km b. 2 km c. 95 ft d. 5500 ft

Last Answer : b. 2 km

What is the dielectric constant of polyethylene (PE) insulator? A. 2.5 B. 3.3 C. 2.27 D. 2.1

Description : What is the dielectric constant of polyethylene (PE) insulator? A. 2.5 B. 3.3 C. 2.27 D. 2.1

Last Answer : C. 2.27

Capacitance grading of cable implies (a) use of dielectrics of different permeabilities (b) grading according to capacitance of cables per km length (c) cables using single dielectric in different concentrations (d) capacitance required to be introduced at different lengths to counter the effect of inductance (e) none of the above

Description : Capacitance grading of cable implies (a) use of dielectrics of different permeabilities (b) grading according to capacitance of cables per km length (c) cables using single dielectric in different ... introduced at different lengths to counter the effect of inductance (e) none of the above

Last Answer : (a) use of dielectrics of different permeabilities

If temperature change is 19°C, what amount of change to sound velocity is possible? A. 11.53 ft/s B. 11.53 m/s C. 19.304 ft/s D. 19.304 m/s

Description : If temperature change is 19°C, what amount of change to sound velocity is possible? A. 11.53 ft/s B. 11.53 m/s C. 19.304 ft/s D. 19.304 m/s

Last Answer : B. 11.53 m/s

The ratio of speed of light in air to the speed of light in another substance is called the a. Speed factor b. Index of reflection c. Index of refraction d. Dielectric constant

Description : The ratio of speed of light in air to the speed of light in another substance is called the a. Speed factor b. Index of reflection c. Index of refraction d. Dielectric constant

Last Answer : c. Index of refraction

Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Description : Referred to the dielectric constant of a transmission line material. A. Inductance and capacitance B. Velocity factor C. Characteristic impedance D. Propagation velocity

Last Answer : B. Velocity factor

If Ns=250, determine the earth radius k-factor. A. 1.98 B. 1.23 C. 1.33 D. 1.29

Description : If Ns=250, determine the earth radius k-factor. A. 1.98 B. 1.23 C. 1.33 D. 1.29

Last Answer : B. 1.23

A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 kW. What is the gain in dB obtain by the use of the reflector ? ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6

What is the typical velocity factor of coaxial cables? A. 0.6 to 0.8 B. 0.3 to 0.5 C. 0.5 to 0.9 D. 0.4 to 0.6

Description : What is the typical velocity factor of coaxial cables? A. 0.6 to 0.8 B. 0.3 to 0.5 C. 0.5 to 0.9 D. 0.4 to 0.6

Last Answer : A. 0.6 to 0.8

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

The location of AsiaSat I. A. 105.5˚East B. 151.5˚East C. 115.5˚East D. 170.5˚East

Description : The location of AsiaSat I. A. 105.5˚East B. 151.5˚East C. 115.5˚East D. 170.5˚East

Last Answer : A. 105.5˚East

Which of the following is standardized as part of GSM phase 2+ that can offer theoretical data speeds of upto 115 kbit/s? A. EDGE B. GPRS C. WAP D. Bluetooth

Description : Which of the following is standardized as part of GSM phase 2+ that can offer theoretical data speeds of upto 115 kbit/s? A. EDGE B. GPRS C. WAP D. Bluetooth

Last Answer : B. GPRS

Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Description : Assume a frequency of 4 MHz, determine the phase shift offered by the line in the above problem. A. 108.5˚ B. 106.5˚ C. 115.5˚ D. 166.5˚

Last Answer : D. 166.5˚

ECE Board Exam March 1996 One hundred twenty µbars of pressure variation is equal to A. 120 dBSPL B. 115.56 dBSPL C. 41.58 dBSPL D. 57.78 dBSPL

Description : ECE Board Exam March 1996 One hundred twenty µbars of pressure variation is equal to A. 120 dBSPL B. 115.56 dBSPL C. 41.58 dBSPL D. 57.78 dBSPL

Last Answer : B. 115.56 dBSPL

A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural frequency (f n ), respectively, are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz

Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... , are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz

Last Answer : a) 0.471 and 1.19 Hz

A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural frequency (f n ), respectively, are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz d) 0.666 and 8.50 Hz

Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... .19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz d) 0.666 and 8.50 Hz

Last Answer : a) 0.471 and 1.19 Hz

Which of the following is not a bounded medium? A. Coaxial line B. Two-wire line C. Waveguide D. Free space

Description : Which of the following is not a bounded medium? A. Coaxial line B. Two-wire line C. Waveguide D. Free space

Last Answer : D. Free space

What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Description : What type of balun (balanced-to-unbalanced) is used in high frequency applications? A. Transformer type balun B. A specially configured coaxial transmission line C. A specially configured parallel-wire line D. A λ/2 transformer balun

Last Answer : B. A specially configured coaxial transmission line

Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Description : Which of the following is considered the most frequently used transmission line? A. Two-wire open line B. Twin lead C. Rigid coaxial line D. Flexible coaxial line

Last Answer : D. Flexible coaxial line

What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Description : What would be the physical length of a tpical coaxial transmission line that is electrically one-quarter wavelength long at 14.1 MHz? A. 20 meters B. 3.51 meters C. 2.33 meters D. 0.25 meter

Last Answer : B. 3.51 meters

What line has a typical velocity factor of about 0.8? A. Shielded pair B. Flexible coaxial C. Twin-lead D. Open-wire line

Description : What line has a typical velocity factor of about 0.8? A. Shielded pair B. Flexible coaxial C. Twin-lead D. Open-wire line

Last Answer : C. Twin-lead

What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Description : What is the characteristic impedance of a coaxial line with the following data: inner diameter = 0.2 in., center conductor diameter = 0.06 in., insulation = Teflon. A. 200Ω B. 75Ω C. 50Ω D. 150Ω

Last Answer : C. 50Ω

What material is most often used for the outer covering of coaxial cables? A. PVC B. Teflon C. PE D. Polystyrene

Description : What material is most often used for the outer covering of coaxial cables? A. PVC B. Teflon C. PE D. Polystyrene

Last Answer : A. PVC

A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Description : A transmission line consisting of two conductors that have equal resistance per unit length. A. Unbalanced line B. Open-wire line C. Balanced line D. Coaxial line

Last Answer : C. Balanced line

Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler

Description : Best choice of transmission line component to couple a coaxial line to a parallel-wire line A. Shorting B. Balun C. Slotted line D. Directional coupler

Last Answer : B. Balun