What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

What does the noise weighting curve shows?
A. Noise signals measured with a 144 handset
B. Power levels of noise found in carrier systems
C. The interfering effect of other frequencies in a voice channel compared with a
reference frequency of one kilohertz
D. Interfering effects of signals compared with a 3-kHz tone
by

1 Answer

Answer :

C. The interfering effect of other frequencies in a voice channel compared with a
reference frequency of one kilohertz
by

Related questions

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa

What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Description : What is the channel spacing for MF-HF voice frequencies? A. 2.8 kHz B. 500 Hz C. 3.5 kHz D. 3 kHz

Last Answer : D. 3 kHz

At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Description : At what power level does a 1 KHz tone cause zero interference (144 weighted)? A. 90 dB B. 90 dBm C. -90 dBm D. -90 dBm

Last Answer : D. -90 dBm

ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Description : ECE Board Exam March 1996 At what power level does a 1 kHz tone cause zero interference (144 weighted) ? A. -90 dB B. -90 dBm C. 90 dBm D. 90 dB

Last Answer : B. -90 dBm

F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Description : F1A weighting refers to ___________. A. -90 dBm B. dBrnc0 C. dBrnc D. F1A handset

Last Answer : C. dBrnc

kilohertz (kHz) is a unit which measures? A. Power used by a current of one ampere B. Electromagnetic radio wave frequencies (Answer) C. Voltage D. Electric resistance

Description : kilohertz (kHz) is a unit which measures? A. Power used by a current of one ampere B. Electromagnetic radio wave frequencies (Answer) C. Voltage D. Electric resistance

Last Answer : B. Electromagnetic radio wave frequencies (Answer)

ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the same as that of the intermediate frequency C. Generates a 1kHz note for Morse code reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Description : ECE Board Exam March 1996 What is the purpose of a beat frequency oscillator (BFO)? A. Aid in the reception of weak voice-modulated signals B. Generates a signal, whose frequency is the ... reception D. Generates an output, whose frequency differs from that of the intermediate frequency by 1 kHz

Last Answer : C. Generates a 1kHz note for Morse code reception

One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Description : One of the reasons why FDM is being replaced by TDM is A. noise is amplified with voice when an FDM system is used B. it is difficult to place channels side by side C. there is more time than frequency D. Most available frequencies has been used

Last Answer : A. noise is amplified with voice when an FDM system is used

An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Description : An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Last Answer : C. Crossfire

Atmospheric noise becomes less severe at frequencies A. above 30 MHz B. below 30 MHz C. above 3000 kHz D. below 3000kHz

Description : Atmospheric noise becomes less severe at frequencies A. above 30 MHz B. below 30 MHz C. above 3000 kHz D. below 3000kHz

Last Answer : A. above 30 MHz

The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Description : The band of frequencies least susceptible to atmospheric noise and interference is: A. 30 – 300 kHz B. 300 – 3000 kHz C. 3 – 30 MHz D. 300 – 3000 MHz

Last Answer : D. 300 – 3000 MHz

Extra-terrestrial noise is observable at frequencies from A. 0 to 20 KHz B. Above 2 GHz C. 8 to 1.43 GHz D. 5 to 8 GHz

Description : Extra-terrestrial noise is observable at frequencies from A. 0 to 20 KHz B. Above 2 GHz C. 8 to 1.43 GHz D. 5 to 8 GHz

Last Answer : C. 8 to 1.43 GHz

____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Description : ____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Last Answer : C. L carrier

What is the channel spacing for SITOR frequencies? A. 500 Hz B. 170 Hz C. 300 Hz D. 3 kHz

Description : What is the channel spacing for SITOR frequencies? A. 500 Hz B. 170 Hz C. 300 Hz D. 3 kHz

Last Answer : A. 500 Hz

How many voice signals (4 kHz max.) would fit into a 5 MHz spectrum? A. 1250 B. 500 C. 1000 D. 1500

Description : How many voice signals (4 kHz max.) would fit into a 5 MHz spectrum? A. 1250 B. 500 C. 1000 D. 1500

Last Answer : A. 1250

Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Description : Interfering effect of noise, C message weighted, is _________. A. dBa B. dBm C. dBmc D. dB

Last Answer : C. dBmc

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Description : Nominal voice channel A. 20 to 20 KHz B. 16 to 16 KHz C. 3 to 3 KHz D. 4 KHz

Last Answer : D. 4 KHz

One of the potential health effects of exposure to high levels of noise is called tinnitus (pron: ti - NI - tes), which means: w) a permanent loss of hearing. x) a persistent ringing or hissing in the ears after exposure. y) a temporary loss of hearing, especially of upper frequencies. z) abdominal discomfort from low frequency noise.

Description : One of the potential health effects of exposure to high levels of noise is called tinnitus (pron: ti - NI - tes), which means: w) a permanent loss of hearing. x) a persistent ringing ... ) a temporary loss of hearing, especially of upper frequencies. z) abdominal discomfort from low frequency noise.

Last Answer : ANSWER: X -- A PERSISTENT RINGING OR HISSING IN THE EARS AFTER EXPOSURE.

What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Description : What is the mixing process? A. Distortion caused by auroral propagation B. The combination of two signals to produce sum and difference frequencies. C. The elimination of noise in wideband receiver by phase differentiation D. The elimination of noise in a wideband receiver by phase comparison

Last Answer : B. The combination of two signals to produce sum and difference frequencies.

What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Description : What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Last Answer : D. 3100 kHz

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Description : Noise that occurs via capacitive or inductive coupling in a cable. A. Crosstalk B. Quantizing noise C. Reference noise D. Tone interference

Last Answer : A. Crosstalk

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Last Answer : C. 22

A radio station is broadcasting at 3750 khz (kilohertz). This station would be found in which radio band? w) 20 meter x) 40 meter y) 80 meter z) 160 meter

Description : A radio station is broadcasting at 3750 khz (kilohertz). This station would be found in which radio band? w) 20 meter x) 40 meter y) 80 meter z) 160 meter 

Last Answer : ANSWER: Y -- 80 METER 

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Description : Industrial noise frequency is between _____. A. 0 to 10 KHz B. 160 MHz to 200 MHz C. 15 to 160 MHz D. 200 to 3000 MHz

Last Answer : C. 15 to 160 MHz

Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Description : Industrial noise frequency is between _________. A. 200 to 3000 Mhz B. 15 to 160 Mhz C. 0 to 10 Khz D. 20 Ghz

Last Answer : B. 15 to 160 Mhz

Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Description : Modulation means A. Varying of information B. Utilization of a single transmission channel to carry multiple signals C. Varying of some parameters of a carrier such as its amplitude to transmit information D. Transmit pulses in DC form on a copper wire

Last Answer : C. Varying of some parameters of a carrier such as its amplitude to transmit information

In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Description : In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Last Answer : B. 120 Hz

A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Description : A superhet receiver has an IF of 455 kHz and is experiencing image-channel interference on a frequency of 1570 kHz. The receiver is tuned to A. 1115 kHz B. 660 kHz C. 2025 kHz D. 910 kHz

Last Answer : B. 660 kHz

Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Last Answer : C. 405.050 MHz

Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Last Answer : B. 401.0125 MHz

If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Description : If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Last Answer : B. 401.00625MHz

Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Description : Emission on a frequency or frequencies immediately outside the necessary bandwidth which result from the modulation process except spurious emission. A. Radiation B. Noise C. Out of the band D. Interference

Last Answer : C. Out of the band

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Which of the following frequencies is normally used for distress and safety communications? A. 4209.5 kHz B. 490 kHz C. 518 kHz D. 2174.5 kHz

Description : Which of the following frequencies is normally used for distress and safety communications? A. 4209.5 kHz B. 490 kHz C. 518 kHz D. 2174.5 kHz

Last Answer : D. 2174.5 kHz

Frequencies above ______ kHz, are referred to as the radio frequencies. A. 20 B. 2 C. 10 D. 200

Description : Frequencies above ______ kHz, are referred to as the radio frequencies. A. 20 B. 2 C. 10 D. 200

Last Answer : A. 20

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Last Answer : D. To protect small signals in PCM from quantizing distortion

How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Description : How wide is the spectrum bandwidth of a single GSM carrier? A. 100 kHz B. 200 kHz C. 50 kHz D. 16 kHz

Last Answer : B. 200 kHz

The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Description : The carrier swing necessary to provide 80% modulation in the FM broadcasting band is __________. A. 150 kHz B. 120 kHz C. 60 kHz D. 75 kHz

Last Answer : B. 120 kHz

How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz