One of the following is not a useful quantity for comparing the noise performance receivers. A. Input noise voltage B. Equivalent noise resistance C. Noise temperature D. Noise figure.

One of the following is not a useful quantity for comparing the noise performance
receivers.
A. Input noise voltage
B. Equivalent noise resistance
C. Noise temperature
D. Noise figure.
by

1 Answer

Answer :

A. Input noise voltage
by

Related questions

ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Description : ECE Board Exam March 1996 A receiver connected to an antenna whose resistance is 50 ohms has an equivalent noise resistance of 30 ohms. What is the receiver’s noise temperature? A. 754 K B. 464 K C. 174 K D. 293 K

Last Answer : C. 174 K

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Description : A figure of merit used to measure the performance of a radiation detector. A. Noise equivalent power B. Ripple factor C. Safe factor D. Quality factor

Last Answer : A. Noise equivalent power

What is the noise voltage across a 300Ω input resistance to a TV set with a 6MHz bandwidth and temperature of 30˚C? A. 2.3 µV B. 3.8µV C. 5.5µV D. 5.4µV

Description : What is the noise voltage across a 300Ω input resistance to a TV set with a 6MHz bandwidth and temperature of 30˚C? A. 2.3 µV B. 3.8µV C. 5.5µV D. 5.4µV

Last Answer : C. 5.5µV

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

ECE Board Exam March 1996 The equivalent noise temperature of the amplifier is 25 K. What is the noise figure? A. 1.86 B. 0.1086 C. 1.086 D. 10.86

Description : ECE Board Exam March 1996 The equivalent noise temperature of the amplifier is 25 K. What is the noise figure? A. 1.86 B. 0.1086 C. 1.086 D. 10.86

Last Answer : C. 1.086

What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Description : What is the reason why companding is employed in PCM systems? A. To overcome impulse noise in PCM receivers B. To allow amplitude limiting in the receivers C. To solve quantizing noise problem D. To protect small signals in PCM from quantizing distortion

Last Answer : D. To protect small signals in PCM from quantizing distortion

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Description : The square of the thermal noise voltage generated by a resistor is proportional to A. its resistance B. its temperature C. the bandwidth over which it is measured D. All of the above

Last Answer : D. All of the above

What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Description : What is the reliable measurement for comparing amplifier noise characteristics? A. Thermal agitation noise B. Noise factor C. Noise margin D. Signal-to-noise

Last Answer : B. Noise factor

___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Description : ___________ is device that measures the internal open circuit voltage of an equivalent noise generator having an impedance of 600Ω and delivering noise power to a 600 Ω load. A. Psophometer B. Barometer C. Reflectometer D. Voltmeter

Last Answer : A. Psophometer

It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Description : It is useful to refer to an isotropic radiator. A. when comparing the gains of directional antennas B. when testing a transmission line for standing wave ratio C. when (in the northern hemisphere) directing the transmission D. when using a dummy load to tune a transmitter

Last Answer : A. when comparing the gains of directional antennas

When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern hemisphere) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Description : When is it useful to refer to an isotropic radiator? A. When comparing the gains of directional antennas B. When testing a transmission line for standing wave ratio C. When (in the northern ... ) directing the transmission in a southerly direction D. When using a dummy load to tune a transmitter

Last Answer : A. When comparing the gains of directional antennas

Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured C. A random voltage across the resistor does not exist D. All formula referring to random noise are applicable only to the value of such noise.

Description : Indicate the false statement A. The noise generated in a resistance or the resistive component of any impedance is random. B. Random noise power is proportional to the bandwidth over which is measured ... exist D. All formula referring to random noise are applicable only to the value of such noise.

Last Answer : C. A random voltage across the resistor does not exist

What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Description : What is the noise factor if the equivalent noise temperature is 25 K? A. 1.09 B. 0.09 C. 0.36 dBm D. 0.36

Last Answer : A. 1.09

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Description : Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Last Answer : C. 4.78 µV

What noise is a transient short-duration disturbance distributed essentially uniformly over the useful passband of a transmission system? A. Flicker noise B. Transit-time noise C. Shot noise D. Impulse noise

Description : What noise is a transient short-duration disturbance distributed essentially uniformly over the useful passband of a transmission system? A. Flicker noise B. Transit-time noise C. Shot noise D. Impulse noise

Last Answer : D. Impulse noise

What is the most commonly used intermediate frequency of radar receivers? A. 40 MHz B. 60 MHz C. 70 MHz D. 30 MHz

Description : What is the most commonly used intermediate frequency of radar receivers? A. 40 MHz B. 60 MHz C. 70 MHz D. 30 MHz

Last Answer : D. 30 MHz

A one-hop, full duplex, microwave system in a space diversity arrangement. Determine “how many receivers in all are used?” A. 8 B. 2 C. 4 D. 6

Description : A one-hop, full duplex, microwave system in a space diversity arrangement. Determine “how many receivers in all are used?” A. 8 B. 2 C. 4 D. 6

Last Answer : B. 2

ECE Board Exam March 1996 A device to be connected across the headset in telephone receivers to reduce the effects of acoustic shock. A. Ground B. Two rectifiers in parallel with opposite polarities C. Protector D. Fuse

Description : ECE Board Exam March 1996 A device to be connected across the headset in telephone receivers to reduce the effects of acoustic shock. A. Ground B. Two rectifiers in parallel with opposite polarities C. Protector D. Fuse

Last Answer : B. Two rectifiers in parallel with opposite polarities

Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Description : Noise at the input to the receiver can be as high as several A. microvolts B. milivolts C. volts D. kilo volts

Last Answer : A. microvolts

The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Description : The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Last Answer : A. Noise density

The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Description : The transistor with the lowest noise figure in the microwave region is a A. MOSFET B. Dual-gate MOSFET C. JFET D. MESFET

Last Answer : D. MESFET

Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Description : Which noise figure represents the lowest noise in receiver? A. 1.6 dB B. 2.1 dB C. 2.7 dB D. 3.4 dB

Last Answer : A. 1.6 dB

Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Description : Calculated the noise figure of the amplifier whose Req equals 2518Ω (RT=600Ω) if its driven by a generator whose output impedance is 50Ω. A. 39.4 B. 3.94 C. 394 D. 0.394

Last Answer : A. 39.4

The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Description : The noise figure of the first circuit in tandem connection is 10.5 dB while its power gain is 15, what is the over all noise figure if the second circuit has a noise figure of 11 dB? A. 11.59 dB B. 11.23 dB C. 10.79 dB D. 10.5 dB

Last Answer : C. 10.79 dB

nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Description : nif stands for A. Non-intrinsic figure B. Noise improvement factor C. Narrow intermediate frequency D. Noise interference figure

Last Answer : B. Noise improvement factor

Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Description : Nif stands for A. Narrow intermediate frequency B. Noise interference figure C. Noise improvement factor D. Non-intrinsic fugure

Last Answer : C. Noise improvement factor

Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

Which of the following is not a source of industrial noise? A. Automobile ignition B. Sun C. Electric Motors D. Leakage from high voltage line

Description : Which of the following is not a source of industrial noise? A. Automobile ignition B. Sun C. Electric Motors D. Leakage from high voltage line

Last Answer : B. Sun

At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Description : At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Last Answer : B. 1.3 µV

The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Description : The most common unit of noise measurement in white noise voltage testing. A. NPR B. dBm C. dBW D. dBrn

Last Answer : A. NPR

Noise limiter is provided on AM receivers to

Last Answer : Noise limiter is provided on AM receivers to reduce interfering noise due to ignition system, reduce noise due to electrical storms, reduce interference due to electrical machinery.

Noise caused by the thermal agitation of electrons in resistance. A. All of these B. Thermal noise C. Johnson’s noise D. White noise

Description : Noise caused by the thermal agitation of electrons in resistance. A. All of these B. Thermal noise C. Johnson’s noise D. White noise

Last Answer : A. All of these

For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Description : For a shortened vertical antenna, where should a loading coil be placed to minimize losses and produce the most effective performance? A. As low as possible on the vertical radiator B. Near the center of the vertical radiator C. As close to the transmitter as possible D. At a voltage node

Last Answer : B. Near the center of the vertical radiator

Comparing the signal strength arriving at the driven element from the desired direction to the signal strength reaching the driver from the opposite direction. A. Directivity B. Sensitivity C. Beamwidth D. Front-to-back ratio

Description : Comparing the signal strength arriving at the driven element from the desired direction to the signal strength reaching the driver from the opposite direction. A. Directivity B. Sensitivity C. Beamwidth D. Front-to-back ratio

Last Answer : D. Front-to-back ratio

A test method of comparing two audio systems by switching inputs so that the same recording is heard in rapid succession over one given system and then the other. A. B test B. A test C. AB test D. C test

Description : A test method of comparing two audio systems by switching inputs so that the same recording is heard in rapid succession over one given system and then the other. A. B test B. A test C. AB test D. C test

Last Answer : C. AB test

Comparing the capacities of a DVD and an ordinary CD, DVD is ______ time bigger than CD. A. 10 B. 20 C. 15 D. 25

Description : Comparing the capacities of a DVD and an ordinary CD, DVD is ______ time bigger than CD. A. 10 B. 20 C. 15 D. 25

Last Answer : C. 15

How is site traffic useful in evaluating marketing? A. Overall site traffic can be followed and a general idea of marketing's impact on it can be determined B. There is no correlation site traffic and marketing C. Ads can send receivers to a specific landing page, which can be tracked D. Product sales from the company website can be attributed directly to the marketing campaign

Description : How is site traffic useful in evaluating marketing? A. Overall site traffic can be followed and a general idea of marketing's impact on it can be determined B. There is no correlation ... be tracked D. Product sales from the company website can be attributed directly to the marketing campaign

Last Answer : C. Ads can send receivers to a specific landing page, which can be tracked

How is site traffic useful in evaluating marketing?  Overall site traffic can be followed and a general idea of marketing and its impact on It can be determined  There is no correlation site traffic and marketing  Ads can send receivers to a specific landing page, which can be tracked  Product sales from the company website can be attributed directly to the marketing campaign

Description : How is site traffic useful in evaluating marketing?  Overall site traffic can be followed and a general idea of marketing and its impact on It can be determined  There is no ... be tracked  Product sales from the company website can be attributed directly to the marketing campaign

Last Answer :  Ads can send receivers to a specific landing page, which can be tracked

Define input offset voltage?

Description : Define input offset voltage?

Last Answer : It is defined as the voltage that must be applied between the input terminals of an op-amp to nullify the output.

Define input offset voltage.

Description : Define input offset voltage.

Last Answer : A small voltage applied to the input terminals to make the output voltage as zero when the two input terminals are grounded is called input offset voltage. 

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Description : Noise can be reduced by A. widening the bandwidth B. narrowing the bandwidth C. increasing temperature D. increasing transistor current levels

Last Answer : B. narrowing the bandwidth