During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause for this is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Question

During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause for this is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

asked Jan 4, 2022 by anonymous

1 Answer

Answer :

Answer: C

answered Jan 4, 2022 by anonymous

Related questions

After turning on the fluorescent lamp shown in the illustration, you note that the ends of the tube alternately glow and becomce dark without illuminating the center. The most obable cause for this is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Description : After turning on the fluorescent lamp shown in the illustration, you note that the ends of the tube alternately glow and becomce dark without illuminating the center. The most obable cause for ... the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Last Answer : Answer: C

The illustration shows a fluorescent light fixture. The ends of the lamp alternately glow and become dark, but the tube will not light. The most probable cause is that ____________. EL-0081 A. component 'D' is loose and due to the ship's vibrations makes and breaks contact B. the power system's voltage is fluctuating in and out of the range necessary for proper operation C. component 'A' is shorted and therefore unable to produce the high voltage required to start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Description : The illustration shows a fluorescent light fixture. The ends of the lamp alternately glow and become dark, but the tube will not light. The most probable cause is that ____________. EL-0081 ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow

Last Answer : Answer: C

During the start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' remain lighted but the tube does not illuminate. The cause of this problem is ____________. EL-0081 A. component 'A' is open B. component 'D' is closed C. component 'C' is the wrong wattage D. component 'B' contacts are stuck closed

Description : During the start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' remain lighted but the tube does not illuminate. The cause of this problem is ____________. EL- ... ' is closed C. component 'C' is the wrong wattage D. component 'B' contacts are stuck closed

Last Answer : Answer: D

What is indicated by gradual blackening at the ends of component 'C' shown in the illustration? EL-0081 A. The unit is in danger of exploding. B. The tube is nearing the end of its useful life. C. The circuit voltage is too high. D. The circuit current is too high.

Description : What is indicated by gradual blackening at the ends of component 'C' shown in the illustration? EL-0081 A. The unit is in danger of exploding. B. The tube is nearing the end of its useful life. C. The circuit voltage is too high. D. The circuit current is too high.

Last Answer : Answer: B

The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within the envelope C. counteract the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Description : The purpose of the capacitor within component 'B' of the circuit shown in the illustration is to ____________. EL-0081 A. prolong the life of the component's contacts B. discharge the neon within ... the inductive reactance in the circuit D. store power to operate the circuit should 'D' open

Last Answer : Answer: A

When changing out component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its base B. there is a danger of phosphor poisoning should 'B''s bulb break C. component 'D' must be closed during the replacement to provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Description : When changing out component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Last Answer : Answer: D

When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its base B. there is a danger of phosphor poisoning should 'B''s bulb break C. component 'D' must be closed during the replacement to provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Description : When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Last Answer : Answer: D

When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1', stop button, 'CR' and 'M' contacts, 'M' coil, 'OL contacts, the 'CR' coil in parallel, 'L2' C. 'L1', stop button, jog button, 'CR' contact, 'CR' relay, 'L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'

Description : When an operating motor is connected to the controller shown in the illustration, the a path of current flow through the circuit is ____________. EL-0010 A. 'L1', stop button, start button, coil 'CR', 'L2' B. 'L1' ... L2' D. 'L1', stop button, start button, 'CR' contact, 'M' contact, 'CR' coil, 'L2'

Last Answer : Answer: B

Which component of the circuit shown in the illustration is the lamp? EL-0081 A. A B. B C. C D. D

Description : Which component of the circuit shown in the illustration is the lamp? EL-0081 A. A B. B C. C D. D

Last Answer : Answer: C

In the system shown in the illustration, the station at section I is unable to signal any other station nor is any other station able to signal the station in section I. The station can, however, ring itself by proper positioning of its selector switch. EL-0093 A. The selector switch is grounded at the problem station diverting current from the other stations' ringing devices. B. There is an open between terminal 'C' of the problem station and the multi-conductor cable to the other stations. C. The contacts to the left of component 'B' are stuck closed allowing only a single station to respond to itself. D. The switch at component 'C' is stuck open.

Description : In the system shown in the illustration, the station at section I is unable to signal any other station nor is any other station able to signal the station in section I. The station can, however, ring ... only a single station to respond to itself. D. The switch at component 'C' is stuck open.

Last Answer : Answer: B

The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. contactor coil '3M' has many shorted turns B. resistor 'R8-A2' has an open C. contacts '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Description : The winch shown in the illustration will not operate in any speed in the lowering direction and at an abnormal speed in 'first point hoist'. The possible cause is that _______________. EL-0102 A. ... '1M' in the power circuit are badly corroded D. master switch contacts 'MS6' have weak springs

Last Answer : Answer: B

The ground detection system, shown in the illustration for a low-voltage, threephase system has a ground in line 'A'. Therefore, lamp 'A' will burn ____________. EL-0009 A. dimly or be out, and lamps 'B' and 'C' will burn brightly B. normally, and lamps 'B' and 'C' will burn dimly or be out C. brightly, and lamps 'B' and 'C' will burn dimly or be out D. brightly, and lamps 'B' and 'C' will burn normally

Description : The ground detection system, shown in the illustration for a low-voltage, threephase system has a ground in line 'A'. Therefore, lamp 'A' will burn ____________. EL-0009 A. dimly or be out, and lamps 'B' and ... and 'C' will burn dimly or be out D. brightly, and lamps 'B' and 'C' will burn normally

Last Answer : Answer: A

As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby component 'E2' and tells the electrician to renew 'E1'. The opera EL-0058 A. burned out rapidly due to an overused and overheated connection terminal which in turn led to 'C' burning out B. installation developed an accidental connection to 'D' and short-circuited the main line resulting in overloaded fuses just after the master switch C. is a 110 volt DC device being used in a 115 volt AC circuit and will conduct only on the positive half-cycle D. is of a lower wattage rating than required for the circuit therefore limiting the current through the alarm relay which will not pick up

Description : As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby ... than required for the circuit therefore limiting the current through the alarm relay which will not pick up

Last Answer : Answer: D

Federal Regulations (46 CFR) require the circuit in the illustration to _________. EL-0009 A. be at the vessel's ship's service generator distribution switchboard for normal power, normal lighting and emergency lighting systems. B. not have any resulting ground currents flow through hazardous locations on a tank vessel where line to line voltage exceeds 3,000 VAC C. not be used on systems where the resulting ground will interfere with the operation of electronic equipment D. All the above are correct

Description : Federal Regulations (46 CFR) require the circuit in the illustration to _________. EL-0009 A. be at the vessel's ship's service generator distribution switchboard for normal power, normal lighting ... ground will interfere with the operation of electronic equipment D. All the above are correct

Last Answer : Answer: A

When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Description : When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted

Last Answer : Answer: A

When maintaining the circuit shown in the illustration, what dangers are associated with component 'C' should it become broken? EL-0081 A. Glass fragments may cut a person's skin. B. The contained mercury vapor is highly toxic. C. The inside coating of phosphor is highly poisonous. D. All of the above.

Description : When maintaining the circuit shown in the illustration, what dangers are associated with component 'C' should it become broken? EL-0081 A. Glass fragments may cut a person's skin. B. The contained mercury ... highly toxic. C. The inside coating of phosphor is highly poisonous. D. All of the above.

Last Answer : Answer: D

As shown in the illustrations of console schematic diagrams, each circuit card and component, such as a relay or indicating lamp, has an identifier attached. This identifier, which is composed of digits and letters, is to ____________. EL-0099 A. be used only by manufacturer's service technicians and is of little importance to the ship's engineers B. identify the overall circuit in which the component or circuit card is being used C. specify the month and year of manufacture so that a similar unit can be ordered as a spare D. indicate where the item may actually be found on the console by section, surface and possible subassembly

Description : As shown in the illustrations of console schematic diagrams, each circuit card and component, such as a relay or indicating lamp, has an identifier attached. This identifier, which is composed of ... where the item may actually be found on the console by section, surface and possible subassembly

Last Answer : Answer: D

What is represented by the two parallel lines within component 'A' of the circuit shown in the illustration? EL-0081 A. A ground connection B. An iron core C. Ventilation openings D. A mounting base

Description : What is represented by the two parallel lines within component 'A' of the circuit shown in the illustration? EL-0081 A. A ground connection B. An iron core C. Ventilation openings D. A mounting base

Last Answer : Answer: B

Which component of the circuit shown in the illustration is the ballast? EL-0081 A. A B. B C. C D. D

Description : Which component of the circuit shown in the illustration is the ballast? EL-0081 A. A B. B C. C D. D

Last Answer : Answer: A

Which component of the circuit shown in the illustration is the starter? EL-0081 A. A B. B C. C D. D

Description : Which component of the circuit shown in the illustration is the starter? EL-0081 A. A B. B C. C D. D

Last Answer : Answer: B

Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three-phase voltage supply C. improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Last Answer : Answer: A

Due to its construction, the component in figure 'A' shown in the illustration has which of the listed advantages compared to bipolar devices? EL-0078 A. Operates with higher voltages and currents allowing its use in high power amplifiers. B. Its stable triggering voltage makes it useful in oscillators and timing circuits. C. Makes use of inherent unidirectional qualities serving as a controllable rectifier. D. Has very high input resistance and uses practically no gate current.

Description : Due to its construction, the component in figure 'A' shown in the illustration has which of the listed advantages compared to bipolar devices? EL-0078 A. Operates with higher voltages and ... as a controllable rectifier. D. Has very high input resistance and uses practically no gate current.

Last Answer : Answer: D

Power necessary to operate the horn relay shown in the illustration ____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through the relay's contacts D. also lights lamps 'R' and 'T'

Description : Power necessary to operate the horn relay shown in the illustration ____________. EL-0093 A. comes from each station's magneto B. is supplied from a 115 volt source C. is conducted through the relay's contacts D. also lights lamps 'R' and 'T'

Last Answer : Answer: A

As shown in the illustration, the symbol is used in electrical drawings to designate a ____________. EL-0026 A. limit switch with one set of normally open contacts B. maintaining type push button with an electrical interlock C. sustaining type push button with a mechanical interlock D. normally closed contact held open mechanically by an interlock

Description : As shown in the illustration, the symbol is used in electrical drawings to designate a ____________. EL-0026 A. limit switch with one set of normally open contacts B. maintaining type ... type push button with a mechanical interlock D. normally closed contact held open mechanically by an interlock

Last Answer : Answer: C

The devices marked 'T' in the illustration are _____________. EL-0080 A. trouble alarm units whose contacts activate when problems arise either on starting or stopping of the motor B. topping lift direction indicators which show alternately whether the motor is hoisting or lowering the load C. timing relay components whose contacts open or close depending on the setting of their pneumatic adjustment D. thawing contactor parts whose contacts start and stop the defrosting cycle of the compressor driven by the motor

Description : The devices marked 'T' in the illustration are _____________. EL-0080 A. trouble alarm units whose contacts activate when problems arise either on starting or stopping of the motor B. topping ... contactor parts whose contacts start and stop the defrosting cycle of the compressor driven by the motor

Last Answer : Answer: C

Which of the listed types of lighting circuits does the diagram shown in the illustration represent? EL-0081 A. High pressure sodium B. Low voltage quartz C. Mercury vapor D. Standard fluorescent

Description : Which of the listed types of lighting circuits does the diagram shown in the illustration represent? EL-0081 A. High pressure sodium B. Low voltage quartz C. Mercury vapor D. Standard fluorescent

Last Answer : Answer: D

What is represented by the solid dots within components 'B' and 'C' of the diagram shown in the illustration? (See illustration EL-0081) EL-0081 A. The fact that these parts are subject to wear and replacement. B. An indication that they are for 110 volt AC operation only. C. The particular components contain a gas such as neon or argon. D. All of the above.

Description : What is represented by the solid dots within components 'B' and 'C' of the diagram shown in the illustration? (See illustration EL-0081) EL-0081 A. The fact that these parts are subject to wear and ... only. C. The particular components contain a gas such as neon or argon. D. All of the above.

Last Answer : Answer: C

When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Description : When the circuit shown in the illustration is operating correctly, the voltage at the reference electrode will be kept in the optimum range of ____________. EL-0090 A. 0.01 - 0.05 volt B. 0.80 - 0.85 volt C. 35 - 60 volts D. 100 - 115 volts

Last Answer : Answer: B

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Description : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Last Answer : (d) have all above properties

If power were lost to the winch shown in the illustration while in 'second point hoist' the winch would stop. When power is restored the winch would ______________. EL-0102 A. continue to run at 'second point hoist' unless a different speed is selected by the 'master Switch' B. continue to run but at 'first point' speed, for safety, until the 'master Switch' is brought to 'off' and then back to the desired speed C. remain stopped until the 'safety switch' is recycled either directly or by action of the 'master switch' handle D. remain stopped until the 'master switch' is returned to 'off' closing the 'reset' contacts and then moved to any 'run' position

Description : If power were lost to the winch shown in the illustration while in 'second point hoist' the winch would stop. When power is restored the winch would ______________. EL-0102 A. continue to run at ' ... switch' is returned to 'off' closing the 'reset' contacts and then moved to any 'run' position

Last Answer : Answer: D

To stop the electric motor shown in the illustration, the stop button is depressed, causing ____________. EL-0012 A. coil 'MS' to become de-energized B. contacts 'CR1' and 'MR4' to open C. contacts 'MR1', 'MR2', and 'MR3' to open D. contacts 'MS1', 'MS2', and 'MS3' to open

Description : To stop the electric motor shown in the illustration, the stop button is depressed, causing ____________. EL-0012 A. coil 'MS' to become de-energized B. contacts 'CR1' and 'MR4' to open C. contacts 'MR1', 'MR2', and 'MR3' to open D. contacts 'MS1', 'MS2', and 'MS3' to open

Last Answer : Answer: C

As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow through 'R1' will equal the current flow through 'R2' C. the energy dissipated in 'R1' will be the same as the energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Last Answer : Answer: D

If the motor shown in the illustration will not start when 'Q' is depressed, which of the listed components should be checked FIRST? EL-0017 A. Fuses 'F-1' and 'F-2'. B. Operating coil 'C'. C. Contacts 'H-1', 'H-2', and 'H-3'. D. Contact 'H-4'.

Description : If the motor shown in the illustration will not start when 'Q' is depressed, which of the listed components should be checked FIRST? EL-0017 A. Fuses 'F-1' and 'F-2'. B. Operating coil 'C'. C. Contacts 'H-1', 'H-2', and 'H-3'. D. Contact 'H-4'.

Last Answer : Answer: A

If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is necessary as this is proper operation. B. Reverse the 60 Hz supply connections at 'R1' and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Description : If coil 'R1-R2' at the receiver of figure 'A' shown in the illustration were in 180 degree error with respect to that of the transmitter, what corrective action should be taken? EL-0092 A. No action is ... and 'R2'. C. Interchange connections 'S1' and 'S2'. D. Interchange connections 'S1' and 'S3'.

Last Answer : Answer: B

When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A) and (+10 A) jacks B. 10 MA/ 10 AMP with leads in the (-COMMON) and (+) jacks C. 10 MA/ 10 AMP with leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

The arrow drawn through the component shown in the illustration means that the device's value _____________. EL-0015 A. is fixed and cannot be changed B. is variable between two limits C. has yet to be determined for the circuit application D. is not allowed to change during circuit operation

Description : The arrow drawn through the component shown in the illustration means that the device's value _____________. EL-0015 A. is fixed and cannot be changed B. is variable between two limits C. has yet to be determined for the circuit application D. is not allowed to change during circuit operation

Last Answer : Answer: B

Which of the following actions must be carried out prior to closing the alternator circuit breaker according to the graph shown in the illustration? EL-0002 A. Increase the alternator voltage. B. Decrease the line voltage. C. Increase the line voltage. D. Decrease the line frequency.

Description : Which of the following actions must be carried out prior to closing the alternator circuit breaker according to the graph shown in the illustration? EL-0002 A. Increase the alternator voltage. B. Decrease the line voltage. C. Increase the line voltage. D. Decrease the line frequency.

Last Answer : Answer: A

The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the collector of 'Q1' C. acts as a low capacitive reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Last Answer : Answer: D

Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Description : Component 'C' in section 'I' shown in the illustration represent ____________. EL-0093 A. a selectable holding coil arrangement B. a 'fuse blown' indicator circuit C. 'reset' and 'trouble' lamps D. a handset with switch and voice elements

Last Answer : Answer: D

The 'reset' contacts of the master switch shown in the illustration provides the winch controller with ___________. EL-0102 A. low voltage release B. overload protection C. low voltage protection D. high power factor correction

Description : The 'reset' contacts of the master switch shown in the illustration provides the winch controller with ___________. EL-0102 A. low voltage release B. overload protection C. low voltage protection D. high power factor correction

Last Answer : Answer: C

The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are operated by the same relay coil B. screw connections are on terminal board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Description : The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are ... board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Last Answer : Answer: B

In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the mechanical brake by the jackscrew provided C. disconnect the brake solenoid at 'B1' and 'B2' D. open the test link preventing current flow to the armature

Description : In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the ... at 'B1' and 'B2' D. open the test link preventing current flow to the armature

Last Answer : Answer: D

The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to obtain required speeds B. divert shunt field current for speed control in both directions of operation C. limit armature current in hoist and 'series field' current in lower to obtain required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation

Last Answer : Answer: C

As shown in the illustration, what happens when 'A' is closed, 'B' is in position '2' and component 'E2' burns out? EL-0058 A. 'H' energizes and 'D' makes contact. B. 'F' goes out allowing 'G' to disconnect. C. 'G' sounds an alarm and 'F' illuminates. D. 'C' opens causing 'A' to also open.

Description : As shown in the illustration, what happens when 'A' is closed, 'B' is in position '2' and component 'E2' burns out? EL-0058 A. 'H' energizes and 'D' makes contact. B. 'F' goes out allowing 'G' to disconnect. C. 'G' sounds an alarm and 'F' illuminates. D. 'C' opens causing 'A' to also open.

Last Answer : Answer: C

When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Description : When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Last Answer : Answer: C

The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'

Description : The contacts operated by the D.C. relay coil shown in the illustration are located in the schematic diagram prints at coordinates ____________. EL-0100 A. '41Y' on this page B. '52M52M' and '52H35M' C. '57R' on this page D. '52N' on page '57R'

Last Answer : Answer: C

When 'selector switch' 'SEL8' shown in the illustration is in the 'TEST' position, contacts '3,4' and '7,8' are respectively ____________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed

Description : When 'selector switch' 'SEL8' shown in the illustration is in the 'TEST' position, contacts '3,4' and '7,8' are respectively ____________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed

Last Answer : Answer: B

When 'selector switch' 'SEL8' shown in the illustration is in the 'OFF' position, contacts '3,4' and '7,8' are respectively ____________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed

Description : When 'selector switch' 'SEL8' shown in the illustration is in the 'OFF' position, contacts '3,4' and '7,8' are respectively ____________. EL-0100 A. open; closed B. closed; open C. open; open D. closed; closed

Last Answer : Answer: A

'A-1', as shown in the illustration, is/are ____________. EL-0017 A. normally-closed overload relay contacts B. a double pole knife switch C. normally-open overload relay contacts D. a single pole knife switch

Description : 'A-1', as shown in the illustration, is/are ____________. EL-0017 A. normally-closed overload relay contacts B. a double pole knife switch C. normally-open overload relay contacts D. a single pole knife switch

Last Answer : Answer: A

Component 'B' of section 'I' shown in the illustration represents a _____________. EL-0093 A. bridge rectifier B. selsyn motor C. small generator D. shielded lamp

Description : Component 'B' of section 'I' shown in the illustration represents a _____________. EL-0093 A. bridge rectifier B. selsyn motor C. small generator D. shielded lamp

Last Answer : Answer: C

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions