Description : When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil
Last Answer : Answer: C
Description : In troubleshooting a circuit in a console, you find that a resistor may be faulty. Which of the precautions listed must be observed when using an ohmmeter to carry out this test? A. Correct polarity ... D. The resistor's circuit must be de-energized and at least one end of the component isolated.
Last Answer : Answer: D
Description : While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to ... of the component isolated. D. The meter case must be grounded prior to attaching the leads.
Description : When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust ... -on types D. substitute a new or repaired spare card and check the operation of the circuit
Description : When troubleshooting a motor controller, all indications are that a relay coil should be energized. If there were no magnetic pull, with rated voltage measured across the coil, the most probable cause ... open C. auxiliary contact in series with the coil is defective D. relay armature is stuck
Last Answer : Answer: A
Description : The illustration shows a fluorescent light fixture. The ends of the lamp alternately glow and become dark, but the tube will not light. The most probable cause is that ____________. EL-0081 ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow
Description : During start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' alternately glow and become dark without the tube illuminating. The most probable cause ... start the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow
Description : When troubleshooting a console circuit card suspected of being faulty, first check for proper voltages to the card and then _______________. A. test transistors or integrated circuits for gain and ... D. de-energize the card and check the printed circuit traces for continuity with an ohmmeter
Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit
Description : When troubleshooting a console circuit card which is suspected of being faulty, the first step would be to _____. A. pull the card and measure the value of all resistors B. check for the ... for burned components D. check for continuity of circuit board traces and then the gain of each transistor
Description : As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground
Last Answer : Answer: B
Description : The following statement is an example of what kind of logical fallacy? "The university should increase funding of intramural sports because it has a responsibility to back its sports programs financially." a) ... Reasoning c) Ad Populum (Bandwagon) Argument d) False Analogy e) None of the above
Last Answer : b) Circular Reasoning
Description : In class II restorations, all of the following are considered to occur as probable causes of periodontal problems except: A. Flat ridge B. Faulty or not proper contour C. Not properly polished restoration D. Cervical wall is too deeply apical E. Overextension of lining in cavity
Last Answer : E. Overextension of lining in cavity
Description : A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer ... control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing
Description : When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit
Description : Routine A.C. motor maintenance should include periodic ______________. A. thermometer readings at normal loads to detect abnormal temperature rises B. inspection of the motor's internals for loose rotor bars ... C. bearing replacement each year using sealed units if available D. all of the above
Description : Pick up the consideration to the taken while designing a hospital from the following: (A) The operation theatre unit to be detached as it requires sterilized zone but near the ward for the patients ... post-mortem room (C) Casualty unit should be provided a separate entrance (D) All the above
Last Answer : Answer: Option D
Description : If a DC motor runs faster than designed, with all other conditions being normal, the possible cause could be a/an ______________. A. shorted shunt field coil B. open armature coil C. reversed commutating pole D. overload
Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings
Description : When troubleshooting motor controllers, a shorted relay or contactor coil is often indicated by _______________. A. a resistance reading of 'infinity' on an ohmmeter B. charred insulation and/or a blown ... of the coil's leads to ground D. a higher-than-normal voltage reading across the winding
Description : When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an ... a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition
Description : An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________. A. not affect the faulty generator due to the compensation of the other generators B. ... between the armature and the bus D. cause high currents to be induced in the field windings
Description : Vessel pitch can be controlled by either the 'bridge or engine room thrust lever' shown in the illustration; but only with one engine on the line whether in 'cruise or maneuver' mode. The cause is most likely a faulty relay _____________. EL-0095 A. #1 B. #2 C. #3 D. #4
Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function
Description : Which of the following statements represents the important factor that must be considered when replacing a faulty diode in the exciter rectifier assembly? A. Be certain that the replacement diode ... The replacement diode must be dipped in varnish prior to installation to protect against humidity.
Description : Two contributors of electronic console failures are heat and vibration. To combat some of their effects, preventive maintenance procedures should include ______________. A. systematic rotation of circuit cards with those ... bolts and changing of the air in the control room D. all of the above
Description : Identify, from among the following, the correct statement. a) One of the main challenges Engineering facing today is the requirement of most systems to work with a multitude of homogenous systems ... of component based assembly, we find that onlyless than 20% of today's is still custom built
Last Answer : c) does not wear-out in the traditional sense of the term, but does tend to deteriorate as it evolves
Description : After turning on the fluorescent lamp shown in the illustration, you note that the ends of the tube alternately glow and becomce dark without illuminating the center. The most obable cause for ... the lamp D. component 'B' contacts are opening and closing thus prohibiting sufficient current flow
Description : A 45-year-old solicitor had an onset of severe, crushing, substernal chest pain while attending a football match. He collapsed on his way to the car. Bystander Cardiorespiratory Resuscitation ... His oxyhemoglobin curve is shifted to the left 5) His pulmonary artery pressure is probably elevated
Last Answer : Answers-5 This young patient with severe central chest pain has probably arrested due to myocardial infarction and arrhythmia. His gases reveal high PO2 following 100% O2 but severe acidosis ... no left to right shunting and high pulmonary pressures would be expected after this arrest scenario.
Description : If a magnetic controller relay fails to drop out when the coil voltage is removed from the relay, the probable cause may be _____________. A. excessive spring tension B. overvoltage C. excessive current D. welded contacts
Description : The purpose of resistor bank 'R1-R5' in the winch circuit shown in the illustration is to ______________. EL-0102 A. limit armature current in lower and 'series field' current in hoist to ... required speeds D. regulate the strength of the brake solenoid 'B1-B2' in both directions of operation
Description : The only point in the steering stand shown in the illustration which needs periodic lubrication is the ______________. EL-0098 A. repeater assembly ball bearings B. steering wheel bearing C. operation selector switch D. course selector pointer
Description : Before testing insulation with a megohmmeter, the windings of large machines should be grounded for about 15 minutes just prior to the test as the ______________. A. insulation may be damaged ... number of leakage paths D. larger machines may acquire a charge of static electricity during operation
Description : In an experimental research study, the primary goal is to isolate and identify the effect produced by the ____. a. Dependent variable b. Extraneous variable c. Independent variable d. Confounding variable
Last Answer : c. Independent variable
Description : Anyone here with anxiety recognize or have this strange symptom?
Last Answer : Sounds like anxiety. Try a cup of chamomile tea or some yoga breathing.
Description : ______________ encompasses all of the technologies that we use in order to create, collect, process, protect and store information.
Last Answer : ______________ encompasses all of the technologies that we use in order to create, collect, process, protect and store information.
Description : The objective of governmental effectiveness or program auditing is to determine if the desired results of a program are being achieved. What is thefirst step in conducting such an audit? a. Identify the ... c. Determine the time frame to be audited. d. Evaluate the system used to measure results.
Last Answer : Evaluate the system used to measure results.
Description : The data Flow Diagram is the basic component of …………… system A) Conceptual B) Logical C) Physical
Last Answer : A) Conceptual
Description : A bus disconnect link is used to isolate _____________. A. one bus bar from another B. the generator circuit breaker from the bus C. different phases from the equalizer connection D. positive and negative buses from the neutral
Description : To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above
Description : Why we need isolation transformers in power circuit ? why cant we use breakers to isolate?
Last Answer : In Isolation transformer is used, if there is change in parameter values of any side, the other side parameters will remain unchanged.
Description : The systematic errors which persist and have regular effects in the performance of a survey operation are due to (A) Carelessness (B) Faulty instrument (C) Inattention (D) None of these
Last Answer : (B) Faulty instrument
Description : Is it normal for parents to isolate a teen?
Last Answer : Sounds like they’re overprotective. But hey, only one way to fix that; break some rules, lose some trust, gain it back and voila looser restrictions.
Description : The steps of historical research method are Options: A) To identify the problem B) To collect the data C) To criticise the data D) All the above
Last Answer : D) All the above
Description : ______________ is one of the primary requirement of datacenter with respect to datacenter virtualization. A. Unmodified operating systems. B. Resource optimization. C. Application Availability. D. Management.
Last Answer : Unmodified operating systems.
Description : The source of emergency lighting and power at loss of normal ship's power on a cargo vessel should be obtained from the ______________. A. emergency generator supply to the emergency ... switchboard C. battery supply to the main switchboard D. turbogenerator supply to the emergency switchboard
Description : What is Business Architecture Development? A. we recognize the risks that might be caused by cloud computing application from a business perspective. B. we identify the applications that support the ... are required to transform current business to cloud computing modes. D. None of the above
Last Answer : A. we recognize the risks that might be caused by cloud computing application from a business perspective.
Description : Which are the operation that a computer performs on data that put in register: a. Register transfer b. Arithmetic c. Logical d. Allof these
Last Answer : d. Allof these
Description : Which operation is extremely useful in serial transfer of data: a. Logical micro operation b. Arithmetic micro operation c. Shift micro operation d. None of these
Last Answer : c. Shift micro operation