When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes

When changing fuses and the spring clips are found to have lost their grip, they should be replaced or _____________. A. tightened firmly with insulated pliers B. clip clamps should be used C. wired closed with uninsulated, varnished copper wire D. carefully bent back to their original shapes
by

1 Answer

Answer :

Answer: B
by

Related questions

When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Description : When replacing fuses, always make sure _______________. A. to stand on a rubber mat and use rubber gloves B. to use insulated pliers or screwdriver C. the fuse clips are straight, tight, and in good contact D. to increase the fuse rating 10% to guard against 'nuisance blowing'

Last Answer : Answer: C

Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to remove fuse from the circuit. C. Replace blown fuse with one of equal voltage and ampere capacity. D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Description : Which of the following precautions should be taken when a blown fuse, rated at 10 amperes, is replaced? A. Short out the fuse before removing it from the circuit. B. Use needle-nose pliers to ... D. Fuses of 10 ampere rating and less are virtually harmless when energized and may be handled freely.

Last Answer : Answer: C

A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Description : A tubular fuse should always be removed from a fuse panel with _____________. A. a screwdriver B. a pair of insulated metal pliers C. any insulated object D. fuse pullers

Last Answer : Answer: D

The item referred to as a pigtail on a DC motor brush rigging is a/an ______________. A. feather spring B. uninsulated wire C. flexible spring adjuster D. brush holder

Description : The item referred to as a pigtail on a DC motor brush rigging is a/an ______________. A. feather spring B. uninsulated wire C. flexible spring adjuster D. brush holder

Last Answer : Answer: B

In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above

Description : In addition to short circuits and sustained overloads, fuses are likely to blow due to _____________. A. loose fuse clips B. low ambient temperatures C. low contact resistance D. all of the above

Last Answer : Answer: A

Give purpose and location of i) Uninsulated overlap. ii) Insulated overlap. iii) Neutral section. iv) Section insulator.

Description : Give purpose and location of i) Uninsulated overlap. ii) Insulated overlap. iii) Neutral section. iv) Section insulator.

Last Answer : Ans: i) Insulated overlap: To isolate for operation and maintenance of OHE if two lengths of OHE belong to two elementary sections. Located at feeding posts, sub sectioning posts and booster sections.  ... elementary section. Located at cross over from one track to other, from main line to siding.

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

When changing fuses, you should always _____________. A. wear rubber boots B. use a fuse puller C. stand on a rubber mat D. wear safety glasses

Description : When changing fuses, you should always _____________. A. wear rubber boots B. use a fuse puller C. stand on a rubber mat D. wear safety glasses

Last Answer : Answer: B

Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Description : Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Last Answer : Answer: D

Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be returned to 'zero' on the scale? A. The lead clips should be replaced. B. The batteries should be replaced. C. The test reading should be added to each final reading. D. The test reading should be subtracted from each final reading.

Description : Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be ... be added to each final reading. D. The test reading should be subtracted from each final reading.

Last Answer : Answer: B

Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Description : Carefully read the following descriptions and identify what is being talked about. 1. It consists of two insulated wires twisted around each other, -Technology

Last Answer : 1. Twisted pair cable2. Crosstalk3. Radiowave4. Wired communication channel5. Resource sharing

Why can't they make muffler clamps which are as strong as wire clothes hangers?

Description : Why can't they make muffler clamps which are as strong as wire clothes hangers?

Last Answer : I am sure they can. Your speculation concerning why they don’t makes sense to me.

If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________. A. a blown CLF plunger holding the trip bar in the open position B. a missing CLF C. a misaligned limiter housing assembly D. all of the above

Description : If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________. A. a blown CLF plunger holding the trip bar in the open position B. a missing CLF C. a misaligned limiter housing assembly D. all of the above

Last Answer : Answer: D

A copper wire is bent to form an equilateral triangle of area 16√3 sq.cm. What will be the area (in sq.cm) if the same copper wire was bent to form a square? a) 16 b) 24 c) 32 d) 40 e) None of the above

Description : A copper wire is bent to form an equilateral triangle of area 16√3 sq.cm. What will be the area (in sq.cm) if the same copper wire was bent to form a square? a) 16 b) 24 c) 32 d) 40 e) None of the above

Last Answer : Area of equilateral triangle = 16√3 = √3 (side)2 /4 Or side2 = 16×4 = 64 So each side = 8cm Perimeter = 8×3 = 24 cm Since perimeter of the square is 24 cm, each side = 6cm So area = 6×6 = 36 sq cm Answer: e)

Fuses are usually rated in _____________. A. watts B. amps only C. volts only D. amps and volts

Description : Fuses are usually rated in _____________. A. watts B. amps only C. volts only D. amps and volts

Last Answer : Answer: D

To check the three line fuses of a three-phase system consisting of a three-phase motor, you must _____________. A. place the starter in the 'stop' position B. make sure the motor is operating at full load to guard against a false reading C. place the leads across the 'hot' ends of the fuses D. place the leads across the bottom ends of the fuses

Description : To check the three line fuses of a three-phase system consisting of a three-phase motor, you must _____________. A. place the starter in the 'stop' position B. make sure the motor is operating at full ... leads across the 'hot' ends of the fuses D. place the leads across the bottom ends of the fuses

Last Answer : Answer: A

Due to the operating characteristics of the system, time lag fuses (or dual-element fuses) are necessary for use in _____________. A. main lighting circuits B. motor starting circuit C. emergency lighting circuits D. general alarm circuits

Description : Due to the operating characteristics of the system, time lag fuses (or dual-element fuses) are necessary for use in _____________. A. main lighting circuits B. motor starting circuit C. emergency lighting circuits D. general alarm circuits

Last Answer : Answer: B

Fuses are rated in _____________. A. voltage B. amperage C. interrupting capacity D. all the above

Description : Fuses are rated in _____________. A. voltage B. amperage C. interrupting capacity D. all the above

Last Answer : Answer: D

Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Description : Fuses placed in series with a thermal trip-type circuit breaker are used for _____________. A. time-delay protection B. short-circuit protection C. short duration surge protection D. sustained overload protection

Last Answer : Answer: B

Time delayed or delayed action-type fuses are designed to _____________. A. prevent grounds in branch circuits B. prevent opens in motor circuits C. permit momentary overloads without melting D. guard lighting and electronic circuits

Description : Time delayed or delayed action-type fuses are designed to _____________. A. prevent grounds in branch circuits B. prevent opens in motor circuits C. permit momentary overloads without melting D. guard lighting and electronic circuits

Last Answer : Answer: C

As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground

Description : As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground

Last Answer : Answer: B

A wire is being used as a replacement having twice the length and one-half the cross-sectional area of the original wire. The resistance of this new wire, when compared to that of the original wire, is _____________. A. four times as great B. twice as much C. the same as the original resistance D. one-half of the original resistance

Description : A wire is being used as a replacement having twice the length and one-half the cross-sectional area of the original wire. The resistance of this new wire, when compared to that of the original wire, ... B. twice as much C. the same as the original resistance D. one-half of the original resistance

Last Answer : Answer: A

A replacement wire having twice the length and one-half the cross-sectional area of the original wire will have a resistance that is _____________. A. four times that of the original wire B. twice that of the original wire C. the same as that of the original wire D. one-half that of the original wire

Description : A replacement wire having twice the length and one-half the cross-sectional area of the original wire will have a resistance that is _____________. A. four times that of the original wire B. twice that of ... wire C. the same as that of the original wire D. one-half that of the original wire

Last Answer : Answer: A

A typical slide in a slide presentation would not include a) photo images charts, and graphs b) graphs and clip art c) clip art and audio clips d) full motion video e) None of these

Description : A typical slide in a slide presentation would not include a) photo images charts, and graphs b) graphs and clip art c) clip art and audio clips d) full motion video e) None of these

Last Answer : c) clip art and audio clips

When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust and debris from the card and burnish the sliding connections C. make sure all connections are tight including wire wrappings and push-on types D. substitute a new or repaired spare card and check the operation of the circuit

Description : When troubleshooting a console circuit card suspected of being faulty, the last step would be to _______________. A. check the fuses and voltage levels of all power supplies in the console B. clean dust ... -on types D. substitute a new or repaired spare card and check the operation of the circuit

Last Answer : Answer: D

One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Description : One of the generator bearing shells is generally insulated from the end housing in order to prevent _____________. A. rapid brush wear B. residual magnetism leak off C. excessive field winding heat D. circulation of shaft currents

Last Answer : Answer: D

When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Description : When a transformer is used to step down voltage, the low voltage winding is _____________. A. part of the core B. the primary coil C. not insulated D. the secondary coil

Last Answer : Answer: D

A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Description : A 'dead front' switchboard is one _____________. A. without switches on it B. with insulated switches and no exposed terminals C. without circuit breakers D. without safety hand rails nor rubber mats

Last Answer : Answer: B

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

Define insulated wire.

Description : Define insulated wire. 

Last Answer : Insulated wire: A conductor or multi-stranded conductor which has a insulating material on it is called a insulated wire. 

Define unprotected insulated wire.

Description : Define unprotected insulated wire. 

Last Answer : Unprotected insulated wire: Unprotected insulated wire is which the insulation of the wire is not covered by a protective sheathing to prevent it from mechanical damage. 

Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Description : Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Last Answer : Answer: D

When the current flow through a copper wire increases, its _____________. A. resistance will decrease B. insulation will burn C. temperature will increase D. conductivity will increase

Description : When the current flow through a copper wire increases, its _____________. A. resistance will decrease B. insulation will burn C. temperature will increase D. conductivity will increase

Last Answer : Answer: C

If a fuse blows frequently, one should (a) replace it with a thin wire (b) replace it with a thick copper wire (c) replace it with a paper clip (d) call an electrician

Description : If a fuse blows frequently, one should (a) replace it with a thin wire (b) replace it with a thick copper wire (c) replace it with a paper clip (d) call an electrician

Last Answer : Ans:(d)

What type of machine are wire cutter pliers?

Description : What type of machine are wire cutter pliers?

Last Answer : Feel Free to Answer

State the use of following: (i) Screw driver (ii) Nose pliers (iii) Wire gauge (iv) Test lamp

Description : State the use of following: (i) Screw driver (ii) Nose pliers (iii) Wire gauge (iv) Test lamp 

Last Answer : i) Screw Driver: Usually hand-operated, for turning screws with slotted heads for losing and tightening the screws.  ii) Nose pliers : To hold and tight the wires   iii) Wire Gauge: To ... supply voltage, Verification of voltage & current in the system and also check the open circuit fault. 

A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray can of refrigerant approved for this purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray ... purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Last Answer : Answer: B

How do you politely but firmly ask/tell a co-worker that they need to eat with their mouth closed?

Description : How do you politely but firmly ask/tell a co-worker that they need to eat with their mouth closed?

Last Answer : answer:You don’t, unless you are her very good friend, and even then, it would be tricky. Solve your own problems before you solve someone else’s.

As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Description : As shown in the illustration, the circuit which 'shapes' the linear output of the thrust lever so that the steady-state ship speed is linear with respect to that lever's setting is the _____________. EL-0095 A. 'pitch controller' B. 'error amplifier' C. 'function generator' D. 'servo amplifier'

Last Answer : Answer: C

A collection of pictures that can be inserted into documents is called : (1) Photo Shop (2) Auto Shapes (3) Word Art (4) Clip Art

Description : A collection of pictures that can be inserted into documents is called : (1) Photo Shop (2) Auto Shapes (3) Word Art (4) Clip Art

Last Answer : Clip Art

Which of the following types of insulation will begin to deteriorate FIRST as a result of the heat generated in the conductor it surrounds? A. Varnished cloth B. Rubber C. Silicon D. Asbestos

Description : Which of the following types of insulation will begin to deteriorate FIRST as a result of the heat generated in the conductor it surrounds? A. Varnished cloth B. Rubber C. Silicon D. Asbestos

Last Answer : Answer: B

Which of the following statements best describes the material known as varnished cambric? A. Felted asbestos sealed with varnish. B. Cotton cloth coated with insulating varnish. C. Rubber insulation coated with a layer of tin. D. Paper impregnated with mineral oil, specially wrapped with nonmetallic tape, and coated with varnish.

Description : Which of the following statements best describes the material known as varnished cambric? A. Felted asbestos sealed with varnish. B. Cotton cloth coated with insulating varnish. C. Rubber ... Paper impregnated with mineral oil, specially wrapped with nonmetallic tape, and coated with varnish.

Last Answer : Answer: B

Looking for a quote I once heard, something about how constantly changing your views is better than firmly standing by them?

Description : Looking for a quote I once heard, something about how constantly changing your views is better than firmly standing by them?

Last Answer : this might be close: “I would rather be right than consistent” – Justice Harlan

True or False: 300 years from now when humanity studies the late 1990's into the 2000's outsourcing will be main reason why the U.S.A. lost it's grip on being the worlds #1 economic superpower?

Description : True or False: 300 years from now when humanity studies the late 1990's into the 2000's outsourcing will be main reason why the U.S.A. lost it's grip on being the worlds #1 economic superpower?

Last Answer : How about spiraling national debt incurred in no small part due to our most recent imperialist adventures?

When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, causing glass to fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Description : When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may _____________. A. blow the lamp's circuit breaker B. explode, ... fly in all directions C. short circuit the ballast transformer D. damage the starter and the ballast

Last Answer : Answer: D

A capacitor discolored due to excessive heat should be _____________. A. calibrated B. replaced C. cooled D. soldered

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated B. replaced C. cooled D. soldered

Last Answer : Answer: B

A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Description : A fuse that blows often should be replaced only with a fuse of _____________. A. the recommended current and voltage rating B. higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating

Last Answer : Answer: A

A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Description : A circuit breaker differs from a fuse in that a circuit breaker _____________. A. melts and must be replaced B. is enclosed in a tube of insulating material with metal ferrules at each end C. gives no visual indication of having opened the circuit D. trips to break the circuit and may be reset

Last Answer : Answer: D

_____________ is a collection of wired Ethernet standard for the link layer. A. IEEE 802.3 B. IEEE 802.11 C. IEEE 802.16 D. IEEE 802.15.4

Description : _____________ is a collection of wired Ethernet standard for the link layer. A. IEEE 802.3 B. IEEE 802.11 C. IEEE 802.16 D. IEEE 802.15.4

Last Answer : A. IEEE 802.3