98 views

1 Answer

Answer :

as we knowthat capacitor only allow AC current Rs components grounded that components which are coming in the DC form we have to use capacitor capacitor only pass the AC components which have to be amplifier
Like 0 like

Please log in or register to answer this question.

Related questions

24 views

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

1 answer
114 views

Last Answer : it is the kircjohoffs Voltage law it can be defined as stated that the summation of applied voltage in loop which follows Ohm's law is equal to the voltage drop in the circuit

2 answers
114 views

Last Answer : It is an operating point of transistor.which gives the information of transistor In which region is working

1 answer
424 views

Last Answer : Q pointit is nothing but operating point of transistor which can gives the information about the transistor working in active cutoff or saturation region to the Faithful amplification we have to ... of proper collector emitter voltage during the passage of signal is known as transistor biasing

1 answer
163 views

Last Answer : The operating point of devices is known as Q point (quiescent point) Q point are the values of voltages and currents of a circuit when no signal is present.

1 answer
112 views

Last Answer : the RC coupled amplifier are using the following applications first in public address amplifier system  tape recorders TV VCR and CD players stereo amplifier  and these are the voltage amplification amplifiers

1 answer
89 views

Last Answer : the main components of the circuit are as follows register capacitor an inductor and the supply voltage our current source.

1 answer
0 views

Description : Two amplifiers are connected one after other in series. The first amplifier has a voltage gain of 10 and second has voltage gain of 20. If the input signal is 0.01 V, then calculate the input a.c signal.

0 answers
0 views

Description : Is it possible to bridge an odd number of amplifiers?

Last Answer : No. That's not possible. Amplifiers can only be bridged in pairs, and pairs of pairs, etc. And if they're not identical amps, you're asking for trouble, too. Some stereo amplifiers are wired so that you ... 4-channel, and he's bridging them in some odd way to create a balanced pair of pair of amps.

1 answer
1 view

Description : What are antenna amplifiers used for?

Last Answer : Antenna amplifiers are used to strengthen the signal being supplied to an appliance such as your TV. Amplifiers are necessary when the signal is weak and interferes with your TV reception.

1 answer
2 views

Description : Can I get government assistance if I am deaf and need phone amplifiers?

Last Answer : Some states do have assistance available-- Nevada and Nebraska are two examples. Help from the Federal Government directly is not available through Medicare or the National Institute on Deafness and Other ... do have a directory of local groups that will help-- www.nidcd.nih.gov/directory/

1 answer
1 view

Description : Are phone amplifiers bad for your hearing?

Last Answer : They can be bad for your hearing if they are putting out more than 105 dB. 10 minutes of noise at 105 dB can damage your hearing. Though minor damage can be repaired by itself, repeatedly getting minor damage adds up to major damage and hearing loss.

1 answer
1 view

Description : Are car amplifiers just about volume, or do they improve sound quality, as well?

Last Answer : Cap amplifiers can provide an enhanced audio experience as they often are able to reproduce a wider range of audio frequencies compared to many stock car stereos.

1 answer
2 views

Description : Does the volume go to "11" on any car amplifiers?

Last Answer : No. Police can pull you over for noise pollution so they tend not to make them do higher.

1 answer
4 views

Description : Which car amplifiers work best with MP3 files?

Last Answer : Pioneer is the best amplifer and car system that works with MP3 files.

1 answer
0 views

Description : Are the amplifiers easy to remove?

Last Answer : Yes it's easy to remove amplifiers from your car. First make sure the fuse is out of the power wire , so the wire is not live. Then disconnect the wires from your amp. Then unscrew the amp from where it's mounted.

1 answer
0 views

Description : Are there special amplifiers for hybrid and electric vehicles?

Last Answer : Yes, they draw power differently as to not kill the engine.

1 answer
4 views

Description : Negative feedback in amplifiers – (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and in-creases noise (4) decreases bandwidth and increases noise

Last Answer : (1) increases bandwidth and decreases noise Explanation: Voltage gain, input impedance, output impedance, bandwidth etc. are few important characteristics of an amplifier. These parameters are more or ... be controlled. This can be conveniently achieved by employing a technique, called the feedback.

1 answer
2 views

Description : Negative feedback in amplifiers – (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and in-creases noise (4) decreases bandwidth and increases noise

Last Answer : (1) increases bandwidth and decreases noise Explanation: Voltage gain, input impedance, output impedance, bandwidth etc. are few important characteristics of an amplifier. These parameters are more or ... be controlled. This can be conveniently achieved by employing a technique, called the feedback.

1 answer
4 views

Description : Common basic applications for the operational amplifier include ____________. A. counting, pulsing and clocking amplifiers B. summing, scaling and difference amplifiers C. step-up, step-down and rectifying amplifiers D. all of the above

Last Answer : Answer: B

1 answer
4 views

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

1 answer
16 views

Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit

Last Answer : Answer: A

1 answer
5 views

Description : Since the characteristics of the device shown in figure 'A' of the illustration includes a stable voltage and low current while operating, it can be suitably used in _____________. EL-0065 A. oscillators ... . class A and B amplifiers C. generator rectifier and filtering supplies D. all of the above

Last Answer : Answer: A

1 answer
14 views

Description : Indicate the false statement. A. HF mixer are generally noisier than HF amplifiers. B. Impulse noise voltage is dependent on bandwidth C. Thermal noise is independent of the frequency at which is measured. D. Industrial noise is usually of the impulse type.

Last Answer : B. Impulse noise voltage is dependent on bandwidth

1 answer
3 views

Description : Why are frequency modulation transmitters more efficient? A. Because their power is increased by class C amplifiers B. Because their power is increased by class A amplifiers C. Because their power is increased by class B amplifiers D. Because their power is increased by class AB amplifiers

Last Answer : A. Because their power is increased by class C amplifiers

1 answer
7 views

Description : In a triple conversion superheterodyne receiver, diode mixer stages are operated A. In the linear region B. In the nonlinear region C. As class A amplifiers D. As class B amplifiers

Last Answer : B. In the nonlinear region

1 answer
33 views

Description : If you have available number of power amplifiers with a gain of 100 each, how many such amplifiers do you need to cascade to give an overall gain of 60 dB? A. 3 B. 4 C. 5 D. 2

Last Answer : A. 3

1 answer
3 views

Description : What are feed back amplifiers?

Last Answer : Amplifiers which uses feed back principle is called as feed back amplifiers.

1 answer
3 views

Description : How are amplifiers classified according to the transistor configuration?

Last Answer : 1. Common emitter amplifier 2. Common base amplifier 3. Common collector amplifier

1 answer
2 views

Description : How are amplifiers classified according to the input?

Last Answer : 1. Small – signal amplifier 2. Large – signal amplifier

1 answer
4 views

Description : List the applications of Log amplifiers:

Last Answer : 1.Analog computation may require functions such as lnx, log x, sin hx etc. These functions can be performed by log amplifiers 2.Log amplifier can perform direct dB display on digital voltmeter and spectrum analyzer 3.Log amplifier can be used to compress the dynamic range of a signal

1 answer
3 views

Description : ………………... are needed to communicate with systems on other networks. A. repeaters B. amplifiers C. Bridge D. Gateways

Last Answer : D. Gateways

1 answer
28 views

Description : Which of the following contributes to harmonics distortion in amplifiers? A) Positive feedback B) Presence of noise C) Defective active device D) Non linearity in active device.

Last Answer : D) Non linearity in active device.

1 answer
12 views

Description : What is the primary difference between the NPN and PNP amplifiers?

Last Answer : The polarity of the source voltage

1 answer
3 views

Description : List two common usages of magnetic amplifiers

Last Answer : Servosystems, temperature recorders, or power supplies

1 answer
5 views

Description : The IF amplifiers are connected in what amplifier configuration?

Last Answer : Cascade.

1 answer
8 views

Description : In what two ways are amplifiers classified?

Last Answer : By function and frequency response.

1 answer
2 views

Description : Why do electronic devices use amplifiers?

Last Answer : To amplify the input signal to a usable level.

1 answer
6 views

Description : Optical amplifiers use a ____________________ laser.

Last Answer : pump

1 answer
2 views

Description : Optical amplifiers use ____________________-doped glass.

Last Answer : erbium

1 answer
27 views

Description : Negative feedback in amplifiers (1) increases bandwidth and decreases noise (2) decreases bandwidth and decreases noise (3) increases bandwidth and increases noise (4) decreases bandwidth and increases noise

Last Answer :  increases bandwidth and decreases noise

1 answer
367 views

Description : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Last Answer : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

1 answer
75 views

Description : State classification of Amplifiers.

Last Answer : CLASSIFICATION OF AMPLIFIERS: A] Based on input signal 1. Small signal amplifiers 2. Large signal amplifiers B] Based on output signal 1. Voltage amplifier 2. Power amplifier C ... coupling 1. Direct coupled amplifiers 2. R-C Coupled amplifier 3. Transformer coupled amplifier

1 answer
152 views

Description : Comment on the effect of negative feedback on the gain, input and output resistance of the feedback amplifiers.Describe the gain bandwidth product term used in this context and its importance.

Last Answer : Effect of negative feedback: 1. Gain decreases with negative feedback. 2. Input resistance increases with negative feedback. 3. Output resistance decreases with negative feedback. Explanation ... feedback bandwidth increases which means it is stable output on more range of frequency.

1 answer
58 views

Description : Classify the power amplifiers on the basis of operation and input/output waveforms.

Last Answer : Depending upon the operation and input/output waveforms power amplifiers are classified into following type. 1) Class A amplifier. 2) Class B amplifier. 3) Class C amplifier. 4) Class AB amplifier. 5) Class D amplifier

1 answer
...