State the need of modulation.

State the need of modulation.
by

1 Answer

Answer :

Need of Modulation :-

i)Reduction in the height of antenna

 ii) Avoids mixing of signal

 iii) Increases range of communication.

 iv) Multiplexing is possible

v) Improve quality of reception.
by

Related questions

Define modulation? State the desirable value of modulation index of AM.

Description : Define modulation? State the desirable value of modulation index of AM.

Last Answer : Modulation: It is the process in which any of these Parameters (Amplitude, Frequency, Phase) of high frequency signal (carrier signal) are varied in accordance with low frequency signal(modulating signal) For an AM, modulation index range is 0 to 1.

Define pulse modulation. State its types.

Description : Define pulse modulation. State its types. 

Last Answer : Pulse Modulation - consists essentially of sampling analog information signals and then converting those samples into discrete pulses. OR It consists essentially of sampling analog information signals and then converting those ... PAM - PWM - PPM  ii) Digital Pulse Modulation - PCM - DM - ADM 

Explain how modulation reduces height of antenna and avoid mixing of signals.

Description : Explain how modulation reduces height of antenna and avoid mixing of signals.

Last Answer : Modulation reduces antenna height: For the transmission of radio signals, the antenna height must be multiple of λ/4 ,where λ is the wavelength . λ = c /f where c : is the ... will occupy different slots in the frequency domain (different channels). Thus, modulation avoids mixing of signals.

Give the expression for modulation index for AM and FM.

Description : Give the expression for modulation index for AM and FM.

Last Answer : 1.Modulation index for AM ma=Vm / Vc Where Vm is modulating voltage Vc is the carrier voltage 2.Modulation index for FM mf=δ /fm where δ is the deviation fm is the modulating frequency

Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Last Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

Define modulation index in FM. What is maximum value of deviation ratio.

Description : Define modulation index in FM. What is maximum value of deviation ratio.

Last Answer : Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm). (OR)  

Define modulation index in AM and give its formula.

Description : Define modulation index in AM and give its formula.

Last Answer : In AM wave, the modulation index (m) is defined as the ratio of the amplitude of the modulating signal (Vm ) to the amplitude of carrier signal (Vc). m = Vm / Vc

State the need of stub. Explain single stub and double stub matching.

Description : State the need of stub. Explain single stub and double stub matching.

Last Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible. ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching.  

State the need of AGC. List the different types of AGC with neat graph.

Description : State the need of AGC. List the different types of AGC with neat graph.

Last Answer : Need of AGC:- The need or purpose of AGC circuit is to maintain the output voltage level (volume) of radio receiver constant over a wide range of RF input signal level.  AGC also helps to smooth out the rapid ... of AGC:- 1) Simple AGC 2) Delayed AGC Graphical representation of AGC:- 

Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Description : Define pre-emphasis. State its need. Draw the circuit of pre-emphasis.

Last Answer : Definition- The artificial boosting of higher modulating frequencies to reduce the effect of noise is called as pre-emphasis. Need:- The artificial boosting of higher audio modulating ... by increasing the amplitude of modulating signal at higher frequencies. Circuit diagram 

State the need of AGC.

Description : State the need of AGC.

Last Answer : Need of AGC:- The need or purpose of AGC circuit is to maintain the output voltage level (volume) of radio receiver constant over a wide range of RF input signal level. AGC ... long distance short wave reception & prevents overloading of the last IF amplifier which might otherwise have occurred 

Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Description : Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Last Answer : Horn antenna: Application:- i) Used at microwave frequency. ii) Used in satellite tracking.  Ferrite loop antenna: Application:- In Am radio receiver to receive MW and SW band signals. In FM radio receiver

State and explain the concept of transmission bandwidth.

Description : State and explain the concept of transmission bandwidth.

Last Answer : Bandwidth is defined as the portion of the electromagnetic spectrum occupied by a signal We may also define the bandwidth as the frequency range over which as information signal is transmitted. Bandwidth is the ... to 15 KHZ. Therefore the bandwidth is(f2-f1) BW= f2 - f1= 15000-20=14980Hz

State two disadvantages of TRF receiver over superheterodyne receiver.

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Last Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

State the types of electromagnetic polarization? Define any one of it.

Description : State the types of electromagnetic polarization? Define any one of it.

Last Answer : Transverse electromagnetic wave:- The polarization of a plane EM wave is simply the orientation of the electric field vector with respect to the surface (i.e. looking at the horizon) If ... the field strength varies with change in polarization the wave is said to have an elliptical polarization 

State the process FM detection? State it‟s any two types.

Description : State the process FM detection? State it‟s any two types.

Last Answer : FM detection: In any radio that is designed to receive frequency modulated signals there is some form of FM demodulator or detector. This circuit takes in frequency modulated RF signals and takes the ... 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL)

State the IF frequency and bandwidth of FM receiver.

Description : State the IF frequency and bandwidth of FM receiver.

Last Answer : IF for FM receiver: 10.7 MHz. Bandwidth of FM receiver:88MHz to 108 MHz

State the frequency range for audio frequency and voice frequency.

Description : State the frequency range for audio frequency and voice frequency.

Last Answer : The generally accepted standard range of audible frequencies is 20 to 20,000 Hz, The usable voice frequency band ranges from approximately 300 Hz to 3400 Hz.

Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Description : Explain loop antenna with neat sketch. Draw radiation pattern. State its advantages and applications.

Last Answer : Loop antenna:-The single turn coil carrying RF current through it having length less than the wavelength.   Advantages:- 1. highly directive 2. Small size Applications:- 1. For direction finding 2. In portable receivers 3. In navigation 

State and explain concept of bandwidth.

Description : State and explain concept of bandwidth.

Last Answer : 1. Bandwidth is defined as a range within a band of frequencies or wavelengths. ... For digital devices, the bandwidth is usually expressed in bits per second (bps) or bytes per second. For analog devices, the bandwidth ... or Hertz (Hz) 2.Suppose the frequency range is f1 to f2 , then B.W= f2 - f1

State and explain the types of noise in communication system.

Description : State and explain the types of noise in communication system.

Last Answer : External Noise:  Atmospheric Noise  Atmospheric noise or static is caused by lighting discharges in thunderstorms and other natural electrical disturbances occurring in the atmosphere. These ... between two or more paths, and results from the random fluctuations in the division.

Draw the circuit diagram of PWM using IC555. State its operation.

Description : Draw the circuit diagram of PWM using IC555. State its operation.

Last Answer : Operation: i. The timer IC555 is operated in monostable mode. ii. The negative going carrier pulses are to the differentiator formed by R1 & C1. The differentiator produces sharp negative ... . Thus PWM signal is generated at the output pin (3) of IC555 as monostablemultivibrator. 

Draw block diagram of basic electronic communication system and state the function of each block.

Description : Draw block diagram of basic electronic communication system and state the function of each block.

Last Answer : i) Input signal: - The information can be in the form of sound, picture or data coming from computer. ii) Input transducer: - it converts original information into equivalent electrical ... back to suitable form. vii) Output transducer: - It converts electrical signal into original form. 

State and explain the losses in transmission line.

Description : State and explain the losses in transmission line.

Last Answer : Losses in Transmission Line:- There are three ways in which energy, applied to a transmission may desperate before reaching the load. They are 1) Radiation Losses:- Its occurs when a ... down voltage of the dielectric insulator. Generally when corona occurs, the transmission line is destroyed.

State the super heterodyne principle.

Description : State the super heterodyne principle.

Last Answer : The process of mixing two signals having different frequencies to produce a new frequency i.e., to convert all the incoming frequencies to a lower frequency known as intermediate frequency (IF) . The super heterodyne principle is based on frequency conversion or frequency down conversion.

Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Last Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Description : Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Last Answer : Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below ... the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

Draw and label the circuit diagram of ratio detector

Description : Draw and label the circuit diagram of ratio detector 

Last Answer : Draw and label the circuit diagram of ratio detector  

Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Description : Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Last Answer : L=0.5 mH/Km C=0.08 µF

Explain the working of amplitude limiter in FM receiver with circuit diagram.

Description : Explain the working of amplitude limiter in FM receiver with circuit diagram.

Last Answer : Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy  Circuit Diagram:

Explain duct propagation with neat sketch.

Description : Explain duct propagation with neat sketch.

Last Answer : Duct propagation is a special type and used for very high microwave frequencies. New phenomenon which occurs in super-refraction, also known as ducting. As the height above earth increases, ... in the standard atmosphere. The Duct propagation is used for very high frequencies in GHz range.

A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Last Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Draw circuit diagram of transistor reactance modulator. Explain its working.

Description : Draw circuit diagram of transistor reactance modulator. Explain its working.

Last Answer : Explanation- A reactance modulator is illustrated in figure. It is basically a standard commonemitter class A amplifier. Resistors R1 and R2 from a voltage divider to bias ... frequency, whereas a lower capacitance increases the frequency. The circuit produces direct frequency modulations.

Define and explain the term beam width related to antenna with a sketch.

Description : Define and explain the term beam width related to antenna with a sketch.

Last Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

Define critical frequency w.r. to wave propagation.

Description : Define critical frequency w.r. to wave propagation.

Last Answer : Define critical frequency w.r. to wave propagation.

Define VSWR with refernce to standing waves.

Description : Define VSWR with refernce to standing waves.

Last Answer : Voltage Standing Wave Ratio: The voltage standing wave ratio (VSWR) is the ratio of max voltage to min voltage. VSWR= VMAX /VMIN

Define sensitivity with graph.

Description : Define sensitivity with graph.

Last Answer : Define sensitivity with graph.

Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Description : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Last Answer : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Explain operation of balanced slope detector with „s‟ curve.

Description : Explain operation of balanced slope detector with „s‟ curve.

Last Answer : Diagram: Explanation:   Curve:  

Draw block diagram of FM receiver and explain the use of limiter circuit.

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Last Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Description : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Last Answer : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Explain “BALUN” with neat sketch

Description : Explain “BALUN” with neat sketch

Last Answer : Diagram- Explaination

Explain working of envelope detector with suitable diagram and waveform.

Description : Explain working of envelope detector with suitable diagram and waveform.

Last Answer : Envelope Detector: An Envelope Detector is an electronic circuit that takes a high frequency signal as input and provides an output which is as envelopes of the original signal. The capacitor ... decreases the responsiveness thus, real-world designs must be optimized for the application.

Draw construction of Yagi-Uda antenna and explain.

Description : Draw construction of Yagi-Uda antenna and explain.

Last Answer : Explanation A Yagi-Uda antenna, commonly known as a Yagi antenna, is a directional antenna consisting of multiple parallel elements in a line, usually half-wave dipoles made of ... receiver with a transmission line and additional parasitic elements called reflector and one or more directors.

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Last Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Description : Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Last Answer : Waveform- Explanation When the transmission line is short circuited voltage is zero and current is maximum.The variation is according to the wavelength. When the ... The pattern repeats for every half wavelength. Thus impedance is inverted at every quarter wavelength interval.

Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna

Description : Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna 

Last Answer : i. Rectangular antenna is used in direction finding in portable recievers. ii. Dish antenna is used to transmit and receive signal from satellite. iii. Yagi-Uda antenna is used in HF and VHF range as a TV receiving antenna. iv. Horn antenna is used in satellite tracking.

Explain virtual height with respect to wave propagation with neat sketch.

Description : Explain virtual height with respect to wave propagation with neat sketch.

Last Answer : In ionization layer the incident wave refracts and bends down gradually than sharply.   The incident and refracted rays follow paths that are exactly the same as they would have been if reflection had taken place from a surface located at a greater height called virtual height of this layer. 

a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Description : a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Last Answer : reflection coefficient R=Vr/Vi i. There is no reflected voltage. i.e,Vr=0 R=0 SWR= 1+R/1-R=1 ii. Reflected voltage and incident voltage is equal. Vr=Vi; R=1 SWR= 1+R/1-R=1+1/1-1=infinity iii. If reflected ... and incident voltage =20V. Vr=10 and Vi=20 R=10/20=0.5 SWR= 1+R/1-R=1+.5/1-.5=3