Compare between FM and PM

Compare between FM and PM 
by

1 Answer

Answer :

PARAMETERS
FM
PM
1. Variable parameter of carrier.
Frequency
Phase
2. Variable parameter proportional to modulating voltage. 
Frequency deviation
Phase deviation. 
3. Amplitude of modulated signal.
Constant
Constant. 
4. Noise immunity 
Best of all schemes
Better than AM
5. Coverage area for transmitted power
More
Moderate
6. Signal to noise ratio
Best
Better
by

Related questions

Explain the working of amplitude limiter in FM receiver with circuit diagram.

Description : Explain the working of amplitude limiter in FM receiver with circuit diagram.

Last Answer : Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy  Circuit Diagram:

Draw block diagram of FM receiver and explain the use of limiter circuit.

Description : Draw block diagram of FM receiver and explain the use of limiter circuit.

Last Answer : Diagram Explanation Amplitude limiter: The function of amplitude limiter is to remove all amplitude variation of FM carrier voltage that may occur due to atmospheric disturbances. Use of amplitude limiter makes the system less noisy.

In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Last Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

State the process FM detection? State it‟s any two types.

Description : State the process FM detection? State it‟s any two types.

Last Answer : FM detection: In any radio that is designed to receive frequency modulated signals there is some form of FM demodulator or detector. This circuit takes in frequency modulated RF signals and takes the ... 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL)

State the IF frequency and bandwidth of FM receiver.

Description : State the IF frequency and bandwidth of FM receiver.

Last Answer : IF for FM receiver: 10.7 MHz. Bandwidth of FM receiver:88MHz to 108 MHz

Describe the block diagram of FM superhetrodyne receiver

Description : Describe the block diagram of FM superhetrodyne receiver

Last Answer : RF amplifier:- There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM broadcast the ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Explain with block diagram of Armstrong method of FM generation.

Description : Explain with block diagram of Armstrong method of FM generation.

Last Answer : Explanation:- The crystal oscillator generates the carrier at low frequency typically at 1 MHz this is applied to the combining network and a 90o phase shifter. The modulating signal is passed through an ... power amplifier to raise the power level of the FM signal.  Phasor Diagram:-   

Draw and explain PLL as an FM demodulator.

Description : Draw and explain PLL as an FM demodulator.

Last Answer : Explanation:- FM signal which is to be demodulated is applied to input of PLL.VCO output must be identical to input signal if PLL is to remain locked. As PLL is locked, VCO ... error voltage represents the modulating signal. Thus at the error amplifier output we get demodulated FM output.

Explain reactance modulator for FM generation.

Description : Explain reactance modulator for FM generation.

Last Answer : Explanation :- Audio modulating signal is applied to Q1 which varies the base voltage and current of Q1 according to the input information to be transmitted. The collector current ... lower the frequency & decrease capacitance increase the frequency and thus produce direct FM at output.

Give the expression for modulation index for AM and FM.

Description : Give the expression for modulation index for AM and FM.

Last Answer : 1.Modulation index for AM ma=Vm / Vc Where Vm is modulating voltage Vc is the carrier voltage 2.Modulation index for FM mf=δ /fm where δ is the deviation fm is the modulating frequency

Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Description : Differentiate between AM and FM on the basis of: (i) Definition (ii) Bandwidth (iii) Modulation Index (iv) Application

Last Answer : Compare AM and FM on the basis of i)Definition ii)Bandwidth iii) Wave propogation iv)Number of sidebands

What are the different types of FM detector?

Description : What are the different types of FM detector?

Last Answer : The different types of FM Detectors are: 1. Simple Slope Detector 2. Balanced Slope Detector 3. Ratio Detector 4. Phase Discriminator 5. FM Detector using Phase Locked Loop (PLL) 

Define modulation index in FM. What is maximum value of deviation ratio.

Description : Define modulation index in FM. What is maximum value of deviation ratio.

Last Answer : Modulation Index of FM: It is defined as the ratio of Frequency Deviation (δ) to the modulating signal frequency (fm). (OR)  

List the types of FM detector. Explain any one of them.

Description : List the types of FM detector. Explain any one of them.

Last Answer : Types of FM detector:- 1. Simple slope detector 2. Balanced slope detector 3. Phase discriminator(Foster seely discriminator) 4. Ratio detector 5. PLL detector Simple ... . If the IF amplitude is sufficiently limited prior to reaching the PLL and the loop is properly compensated 

Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Last Answer : block diagram of FM super heterodyne radio receiver

Draw the circuit diagram of varactor diode FM modulator and explain its working.

Description : Draw the circuit diagram of varactor diode FM modulator and explain its working.

Last Answer : Varactor diode modulator is the direct method of FM generation wherein the carrier frequency is directly varied by the modulating signal. A varactor diode is a semiconductor diode whose ... the magnitude of frequency change is proportional to the amplitude of the modulating signal voltage.

For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Description : For AM, fc =500kHz , fm = 5 kHz Determine: (i) Upper and lower sideband frequencies (ii) Bandwidth

Last Answer : Given data fc = 500KHz , fm = 5KHz USB =fc+fm USB = 500+5  =505 KHz. LSB =fc – fm LSB = 500 – 5  =495 KHz Bandwidth = 2fm .  = 2* 5 =10 KHz

Explain pre-emphasis and de-emphasis concept in FM.

Description : Explain pre-emphasis and de-emphasis concept in FM.

Last Answer : Pre-emphasis:- In an FM system the higher frequencies contribute more to the noise than the lower frequencies. Because of this all FM systems adopt a system of pre-emphasis where the higher frequencies are ... at receiver to improve the noise immunity Pre-emphasis/ De-emphasis graph:

Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Description : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Last Answer : Compare between simplex and full duplex communication on the basis of: 1) Definition 2) Sketch

Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Description : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Last Answer : Compare PAM, PWM, and PPM on the basis of i. Variable characteristics ii. Bandwidth iii. Information contained in iv. Transmitted power

Compare ground wave propagation. Sky wave propagation and space wave propagation.

Description : Compare ground wave propagation. Sky wave propagation and space wave propagation.

Last Answer : Sr. N o Parameter Ground Wave Propagation Sky Wave Propagation Space wave Propagation 1 Frequency Range 30 kHz to 3 MHz  3 MHz to 30 MHz frequencies above 30 MHz 2 ... These waves have line of sight propagation, ... 6 Fading Problem less Severe Less

Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

Description : Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

Last Answer : Compare ground wave and space wave propagation on the basis of: (i) Frequency range (ii) Method of propagation.

Compare TRF and super heterodyne receivers.

Description : Compare TRF and super heterodyne receivers.

Last Answer : Compare TRF and super heterodyne receivers. 

Compare resonant and non-resonant antennas.

Description : Compare resonant and non-resonant antennas.

Last Answer : Distinguish between resonant and non-resonant antennas.

Compare between simplex and duplex communication

Description : Compare between simplex and duplex communication 

Last Answer : simplex and duplex communication :

Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Description : Define the following terms related to antennas; (i) Antenna resistance (ii) Directivity (iii) Antenna gain (iv) Power density

Last Answer : Antenna Resistance - The resistance of an antenna has two components: 1. Its radiation resistance due to conversion of power into electromagnetic waves 2. The resistance due to actual losses in the ... the transmitter power divided by the surface area of a sphere (4πR2) at that distance.

Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Description : Draw practical set-up and explain the procedure to measure selectivity of radio receiver.

Last Answer : Procedure to measure selectivity of radio receiver: Throughout the measurement the receiver is kept tuned to desired frequency 950 Khz. Now the generator output frequency is deviated below ... the generator output voltage is adjusted to get a standard 50 miliwatt receiver output power.

Draw and label the circuit diagram of ratio detector

Description : Draw and label the circuit diagram of ratio detector 

Last Answer : Draw and label the circuit diagram of ratio detector  

Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Description : Draw the structure and state applications of: i) Ferrite loop (rod) antenna ii) Horn antenna

Last Answer : Horn antenna: Application:- i) Used at microwave frequency. ii) Used in satellite tracking.  Ferrite loop antenna: Application:- In Am radio receiver to receive MW and SW band signals. In FM radio receiver

Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Description : Calculate the characteristics impedance for a transmission line having L=0.5 mH/Km, C=0.08 µF and negligible R and G.

Last Answer : L=0.5 mH/Km C=0.08 µF

State the need of stub. Explain single stub and double stub matching.

Description : State the need of stub. Explain single stub and double stub matching.

Last Answer : Stub:- Stub is the piece of short circuited transmission line which is used to tune out the reactance of the load when connected across the transmission line as close as possible. ... but lengths are independently adjustable. The double stub matching provides wide range of impedance matching.  

Explain duct propagation with neat sketch.

Description : Explain duct propagation with neat sketch.

Last Answer : Duct propagation is a special type and used for very high microwave frequencies. New phenomenon which occurs in super-refraction, also known as ducting. As the height above earth increases, ... in the standard atmosphere. The Duct propagation is used for very high frequencies in GHz range.

A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Description : A superheterodyne radio receiver with an IF of 455KHZ is turned to 1000KHZ. Find: (i) Image frequency (ii) Local oscillator frequency

Last Answer : Given Intermediate Frequency fi=455KHz Signal frequency =fs=1000KHz Local oscillator frequency fo=fs+fi  Fo=1000KHz+455KHz  =1455KHz Image frequency is the input frequency which produces the same intermediate frequency fsi=fs+2fi  =1000KHz+2*455KHz  =1910KHz 

Draw circuit diagram of transistor reactance modulator. Explain its working.

Description : Draw circuit diagram of transistor reactance modulator. Explain its working.

Last Answer : Explanation- A reactance modulator is illustrated in figure. It is basically a standard commonemitter class A amplifier. Resistors R1 and R2 from a voltage divider to bias ... frequency, whereas a lower capacitance increases the frequency. The circuit produces direct frequency modulations.

Define and explain the term beam width related to antenna with a sketch.

Description : Define and explain the term beam width related to antenna with a sketch.

Last Answer : Definition: The beam width of an antenna is described as the angles created by comparing the half power point (3dB) on the main radiation lobe to its maximum power point. As an example the beam width ... max voltage at center of lobe (these point are known as half power points.) Sketch-  

State and explain the concept of transmission bandwidth.

Description : State and explain the concept of transmission bandwidth.

Last Answer : Bandwidth is defined as the portion of the electromagnetic spectrum occupied by a signal We may also define the bandwidth as the frequency range over which as information signal is transmitted. Bandwidth is the ... to 15 KHZ. Therefore the bandwidth is(f2-f1) BW= f2 - f1= 15000-20=14980Hz

Define critical frequency w.r. to wave propagation.

Description : Define critical frequency w.r. to wave propagation.

Last Answer : Define critical frequency w.r. to wave propagation.

Define VSWR with refernce to standing waves.

Description : Define VSWR with refernce to standing waves.

Last Answer : Voltage Standing Wave Ratio: The voltage standing wave ratio (VSWR) is the ratio of max voltage to min voltage. VSWR= VMAX /VMIN

State two disadvantages of TRF receiver over superheterodyne receiver.

Description : State two disadvantages of TRF receiver over superheterodyne receiver.

Last Answer : Disadvantages of TRF Receiver: 1. Instability due to oscillatory nature of RF amplifier. 2. Variation in bandwidth over tuning range. 3. Insufficient selectivity at high frequencies 4. Poor adjacent channel rejection capability 

Define sensitivity with graph.

Description : Define sensitivity with graph.

Last Answer : Define sensitivity with graph.

Explain operation of balanced slope detector with „s‟ curve.

Description : Explain operation of balanced slope detector with „s‟ curve.

Last Answer : Diagram: Explanation:   Curve:  

Explain “BALUN” with neat sketch

Description : Explain “BALUN” with neat sketch

Last Answer : Diagram- Explaination

Explain working of envelope detector with suitable diagram and waveform.

Description : Explain working of envelope detector with suitable diagram and waveform.

Last Answer : Envelope Detector: An Envelope Detector is an electronic circuit that takes a high frequency signal as input and provides an output which is as envelopes of the original signal. The capacitor ... decreases the responsiveness thus, real-world designs must be optimized for the application.

Draw construction of Yagi-Uda antenna and explain.

Description : Draw construction of Yagi-Uda antenna and explain.

Last Answer : Explanation A Yagi-Uda antenna, commonly known as a Yagi antenna, is a directional antenna consisting of multiple parallel elements in a line, usually half-wave dipoles made of ... receiver with a transmission line and additional parasitic elements called reflector and one or more directors.

A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Description : A load of 200 ohm is used to match 300 ohm transmission line to achieve SWR=1. Find out the required characteristic impedance of a quarter of a quarter wave transformer connected directly to the load.

Last Answer : Solution :

Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Description : Why should local oscillator frequency be greater than signal frequency in AM receiver? Also explain why IF has constant value?

Last Answer : Reason for LO frequency to be greater than signal frequency The local oscillator frequency (f0) is made greater than signal frequency (Fs) in radio receiver: Local oscillator frequency range is 995 ... frequency of desired signal because the IF is constant and same for all the incoming RF signal.

Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Description : Draw waveform for standing waves on an open and shorted line. Prove that impedance is inverted at every quarter wavelength interval.

Last Answer : Waveform- Explanation When the transmission line is short circuited voltage is zero and current is maximum.The variation is according to the wavelength. When the ... The pattern repeats for every half wavelength. Thus impedance is inverted at every quarter wavelength interval.

Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna

Description : Write one application of following antenna i. Rectangular antenna ii. Dish antenna iii. Yagi-Uda antenna iv. Horn antenna 

Last Answer : i. Rectangular antenna is used in direction finding in portable recievers. ii. Dish antenna is used to transmit and receive signal from satellite. iii. Yagi-Uda antenna is used in HF and VHF range as a TV receiving antenna. iv. Horn antenna is used in satellite tracking.

Explain virtual height with respect to wave propagation with neat sketch.

Description : Explain virtual height with respect to wave propagation with neat sketch.

Last Answer : In ionization layer the incident wave refracts and bends down gradually than sharply.   The incident and refracted rays follow paths that are exactly the same as they would have been if reflection had taken place from a surface located at a greater height called virtual height of this layer. 

a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Description : a) For a transmission line, Find SWR and reflection coefficient R if, i. There is no reflected voltage. ii. Reflected voltage and incident voltage is equal. iii. If reflected voltage=20V and incident voltage=10V. iv. If reflected voltage=10V and incident voltage =20V.

Last Answer : reflection coefficient R=Vr/Vi i. There is no reflected voltage. i.e,Vr=0 R=0 SWR= 1+R/1-R=1 ii. Reflected voltage and incident voltage is equal. Vr=Vi; R=1 SWR= 1+R/1-R=1+1/1-1=infinity iii. If reflected ... and incident voltage =20V. Vr=10 and Vi=20 R=10/20=0.5 SWR= 1+R/1-R=1+.5/1-.5=3