Description : Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.
Last Answer : Answer :
Description : The shunt used in milliammeter
Last Answer : The shunt used in milliammeter will extend the range and reduce the meter resistance.
Description : A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω
Last Answer : A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is Manganin wire of 25 m Ω
Description : A DC ammeter has resistance `0.1 Omega` and its current ranges `0-100 A`. If the range is to be extended to `0-500`, then the following shunt resistan
Last Answer : A DC ammeter has resistance `0.1 Omega` and its current ranges `0-100 A`. If the range is to be extended ... Omega` C. `0.025 Omega` D. `0.25 Omega`
Description : A moving coil galvanometer is converted into an ammeter reads upto `0.03 A` by connecting a shunt of resistance `4r` across it and ammeter reads up `0
Last Answer : A moving coil galvanometer is converted into an ammeter reads upto `0.03 A` by connecting a shunt of resistance `4r` ... `0.02A` C. `0.03A` D. `0.04A`
Description : Calculate the shunt resistance needed to increase the FSD of an ammeter 5 times if the meter resistance is 1kohm
Last Answer : 250ohms
Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω
Last Answer : d) 0.03 Ω
Description : Sketch the circuit of basic DC ammeter , derive equation for shunt resistance.
Last Answer : Derivation The basic movement of dc ammeter circuit consists of D' Arsonval galvanometer. When large current is to be measured then some extra modification is required. For measurement of large current by using ... same. Vsh =Vm m IshRsh=ImRm Rsh=ImRm/Ish Rsh=ImRm/(I-Im)
Description : When used for taking resistance measurements, a volt-ohm-milliammeter is normally powered by _____________. A. a hand cranked generator B. internal storage batteries C. the current in the circuit being tested D. a step down transformer
Last Answer : Answer: B
Description : Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer ... range setting B. weak batteries C. a faulty zero ohms knob D. a faulty meter movement
Description : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be
Last Answer : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) ... 001` B. `0.01` C. 1 D. `0.05`
Description : Decreasing the value of the shunt resistor of an ammeter, it current measuring capability
Last Answer : increases
Description : An ammeter has a full-scale deflection current of 100mA. If the same ammeter is used to measure a full-scale current of 1.0ampere, what is the value of the shunt resistor in ohms if the voltage across the meter is 9.0 volts?
Last Answer : 10 ohms
Description : What is ammeter shunt ?
Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.
Description : Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter
Last Answer : Answer: D
Description : Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In ... with the meter movement. D. In parallel with the load and in parallel with the meter movement.
Description : The shunt of a DC ammeter should be connected in __________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. ... and in parallel with the meter movement D. series with the load and in series with the meter movement
Last Answer : Answer: A
Description : Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter
Last Answer : Answer: C
Description : The shunt used in an ammeter should be connected in ____________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. ... in parallel with the meter movement D. series with the load and in series with the meter movement
Description : Draw and state how Aryton shunt type DC ammeter . State advantage of using Aryton shunt.
Last Answer : OR The Aryton shunt eliminates the possibility of having the meter in the circuit without a shunt. This advantage is gained at the price of slightly higher overall Aryton shunt ammeter. In this ... between shunts. 3. Another advantage is that it may be used as a wide range ammeter.
Last Answer : The function of shunt in an ammeter is to by pass the current.
Description : Assertion A: Large size stones are required in stone revetment in shore protection. Reason R: Resistance of stone to wave force is proportional to its volume and wave force is proportional to the exposed area of the stone. ... of A (C) A is true but R is false (D) A is false but R is true
Last Answer : (A) Both A and R is true and R is the correct explanation of A
Description : A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of + or - 2%. A meter reading of 10 milliamps would indicate a line current of between _____________. A. 9.8 ... 9.8 and 10.2 milliamperes C. 8.0 and 12.0 milliamperes D. 8.0 and 10.0 milliamperes
Description : To send 10% of the main current through a moving coil galvanometer of resistance `99omega`, the shunt required is –
Last Answer : To send 10% of the main current through a moving coil galvanometer of resistance `99omega`, the shunt ... `11Omega` C. `10Omega` D. `9.9Omega`
Description : A permanent magnet moving coil instrument gives full scale deflection of 25mA when a voltage of 75mV is applied across it. Calculate: (i) Resistance of shunt required for full scale deflection of 150 A. (ii) Series resistance for full scale deflection of 500 V.
Description : A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with _____________. A. both meters in series with the ... parallel with the resistance D. the ammeter in parallel and the voltmeter in series with the resistance
Description : To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt
Description : A galvanometer has resistance of 120 Ω. In order to pass 5% of the main current in it, the value of shunt resistance Rs must be equal to a) 6.3 Ω b) 6 Ω c) 2 Ω d) 2.3 Ω
Last Answer : a) 6.3 Ω
Description : Assertion A: Depth and width required at the entrance to a harbour are more than those required in the channel. Reason R: The entrance to a harbour is usually more exposed to waves as compared to the harbour itself. ... explanation of A (C) A is true but R is false (D) A is false but R is true
Description : Assertion : Two resistance wires shown in figure are of same material. They have equal length. More heat is generated in wire A. Reason : In series `H
Last Answer : Assertion : Two resistance wires shown in figure are of same material. They have equal length. More ... . If Assertion is false but Reason is true.
Description : Assertion `:-` Haemodialysis method is used in case of kidney failure. Reason `:-` Malfunctioning of kidney leads to uremia.
Last Answer : Assertion `:-` Haemodialysis method is used in case of kidney failure. Reason `:-` Malfunctioning of ... . D. If both Assertion & Reason are false.
Description : Assertion : In case of vegetatively propagated crops, pure line selection is not requried. Reason : Hybrid vigour is mostly used in vegetatively propa
Last Answer : Assertion : In case of vegetatively propagated crops, pure line selection is not requried. Reason : ... D. If both assertion and reason are false
Description : Assertion : GM foods are facing widerspread resistance by the people Reason : GM foods hve mutated genes which cause infections and alleriges
Last Answer : Assertion : GM foods are facing widerspread resistance by the people Reason : GM foods hve mutated ... . If both the assertion and reason are false
Description : Assertion : A resistance wire is broken into four pices and all are connected in parallel. Then, net resistance becomes 1/16 times. Reason : In parall
Last Answer : Assertion : A resistance wire is broken into four pices and all are connected in parallel. Then, net ... D. If Assertion is false but Reason is true.
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : Assertion:- `N_(2)^(+)` is more stable than `N_(2)^(-)` Reason:- `N_(2)^(+)` has less electrons in antibonding orbital .
Last Answer : Assertion:- `N_(2)^(+)` is more stable than `N_(2)^(-)` Reason:- `N_(2)^(+)` has ... the Reason is False. D. If both Assertion & Reason are false
Description : Assertion (A) : Half life of a radioactive isotope is the time required to decrease its mass number by half Reason (R ) : Half life of radioactive iso
Last Answer : Assertion (A) : Half life of a radioactive isotope is the time required to decrease its mass number by half ... . If both (A) and (R ) are incorrect.
Description : Assertion `:-` Inspiration can occur if intra pulmonary pressure is less than the atmospheric pressure. Reason `:-` Inspiration is initiated by the re
Last Answer : Assertion `:-` Inspiration can occur if intra pulmonary pressure is less than the atmospheric pressure. ... D. If both Assertion & Reason are false.
Description : Assertion :- Filtration of colloidal particles is not possible by filter paper. Reason :- Size of colloidal particle is less than filter paper pores.
Last Answer : Assertion :- Filtration of colloidal particles is not possible by filter paper. Reason :- Size of ... D. If both Assertion & Reason are False.
Description : Assertion (A) : `beta`-particles have greater penetrating power than `alpha`-rays but less than `gamma`-rays Reason (R ) : `beta`-particles are lighte
Last Answer : Assertion (A) : `beta`-particles have greater penetrating power than `alpha`-rays but less than `gamma`-rays ... . If both (A) and (R ) are incorrect.
Description : Assertion : o-Hydrozybenaldehyde is less soluable in water than p-Hydroxybenzalbenzaldehye. Reason : Intra molecular hydrogen bonding in o-Hydrozbenza
Last Answer : Assertion : o-Hydrozybenaldehyde is less soluable in water than p-Hydroxybenzalbenzaldehye. Reason : Intra ... D. Assertion is false, Reason is true
Description : Assertion : Potential difference across the terminals of a battery is always less than the emf of the battery. Reason : During discharging of a batter
Last Answer : Assertion : Potential difference across the terminals of a battery is always less than the emf of the ... . If Assertion is false but Reason is true.
Description : Assertion: Communities that comprise of more species tend to be more stable. Reason: A higher number of species results in less animal variation in to
Last Answer : Assertion: Communities that comprise of more species tend to be more stable. Reason: A higher number ... D. If both assertion and reason are false.
Description : A switchboard ammeter indicates a reading slightly above 'zero' when the leads are disconnected, this is caused by _____________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. capacitors inside the meter storing charges
Description : An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of ___________. A. mechanical misalignment of the meter pointer B. a poor ground for the meter case C. static electricity in the air D. resistors inside the meter storing charges
Description : What should be the resistance of a standard ammeter ?
Last Answer : The resistance of a standard ammeter should be zero.
Description : In the circuit shown in Fig. 4.67, the resistance of the ammeter A is negligible and that of thevoltmeter V is very high. When the switch S is open, t
Last Answer : In the circuit shown in Fig. 4.67, the resistance of the ammeter A is negligible and that of ... internal resistance of the cell (iii) value of R.
Description : In the circuit shown in Fig. 4.64, the battery has an emf of 12.0 V and an internal resistance of `5R//11`. If the ammeter reads 2.0 A, what is the va
Last Answer : In the circuit shown in Fig. 4.64, the battery has an emf of 12.0 V and an internal resistance of ` ... ammeter reads 2.0 A, what is the value of R ?
Description : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range
Last Answer : A voltmeter of range 2 V and resistance `300 Omega` cannot be converted into ammeter of range A. `1 A` B. `1 mA` C. `100 mA` D. `10 mA`
Description : In a ammeter `0.2%` of main current passes through the galvanometer. If resistance of galvanometer is `G`, the resistance of ammeter will be
Last Answer : In a ammeter `0.2%` of main current passes through the galvanometer. If resistance of galvanometer is `G`, the ... 1)/(500)G` D. `(500)/(499)G`