Description : If is the diameter of upper circular portion, the area of cross-section of a standard egg shaped sewer, is A. D² B. D² C. D² D. D²
Last Answer : ANS: A
Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0
Last Answer : (B) 12.88
Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0
Last Answer : (b) 12.88
Description : If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2 (D) D/6m(h1 - h2)3
Last Answer : (C) D/6m(h1 - h2)2
Description : The ratio of maximum bending stress to maximum shear stress on the cross section when a shaft is simultaneously subjected to a torque T and bending moment M, a. T/M b. M/T c. 2T/M d. 2M/T
Last Answer : d. 2M/T
Description : Calculate the magnetic field at a point on the centre of the circular conductor of radius 2m with current 8A. a) 1 b) 2 c) 3 d) 4
Last Answer : b) 2
Description : When using the test set-up shown in the illustration, the lighted lamp indicates the winding is ____________. EL-0027 A. grounded B. good C. open D. shorted
Last Answer : Answer: A
Description : During the start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' remain lighted but the tube does not illuminate. The cause of this problem is ____________. EL- ... ' is closed C. component 'C' is the wrong wattage D. component 'B' contacts are stuck closed
Last Answer : Answer: D
Description : When a lighted matchstick is shown before another light source, the shadow of the matchstick is formed on a screen but not the shadow of the flame. Why is it so?
Last Answer : A shadow is a lightless (dark) region formed beyond an opaque object in the direction opposite to the source of light. An opaque object that comes in the way of light prevents the light that is due ... cannot prevent the light from the other source too. Hence the shadow of the flame is not formed.
Description : The greatest eccentricity which a load W can have without producing tension on the cross-section of a short column of external diameter D and internal diameter d, is (A) 4W/ (D² - d²) (B) (D² - d²)/32D (C) (D² + d²)/8D (D) (D² - d²)/8D
Last Answer : (C) (D² + d²)/8D
Description : Which of the listed conditions occur when selection is made for 'third point hoist' on the winch shown in the illustration? EL-0102 A. Master switch contacts '5', '6', '7', '8', and '9' close. B. Contactors '2M', ' ... ' and '2A' drop out. D. Master switch contacts '3','4', '6', '8', and '9' close.
Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given
Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with ... P_(2) = 32 J//s` D. None of these
Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant ... `16 N` C. `24 N` D. `32 N`
Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant ... `0` B. `2A` C. `4A` D. `6A`
Description : The cross-section of a road partly in banking and partly in cutting is shown in the given figure. The area of the shaded portion is (A) b - rd)²/(r - s) (B) b - rd)²/(r + s) (C) ½ × (b + rd)²/(r - s) (D) b - rd)²/(s - r)
Last Answer : (A) b - rd)²/(r - s)
Description : The area of the cross-section of a road fully in banking shown in the given figure, is (A) [sb² + r² (2bd + sd)²]/(r² - s²) (B) [sb² + r² (2bd + sd)²]/(r² - s5 ) (C) [sb² + r² (2bd + sd)²]/(r - s) (D) None of these
Last Answer : (A) [sb² + r² (2bd + sd)²]/(r² - s²)
Description : The moment of inertia of a hollow circular section whose external diameter is 8 cm and interial diameter is 6 cm about the axis passing through its centre is a.66.8 cm4 b.137.5 cm4 c.550 cm4 d.33.4 cm4 e.275 cm4
Last Answer : b. 137.5 cm4
Description : The polar moment of inertia of a hollow circular section whose external diameter is 8 cm and internal diameter of 6 cm will be a.137.5 cm4 b.107 dynes c.275 cm4 d.550 cm4 e.1100 cm4
Last Answer : c. 275 cm4
Description : If is the diameter of upper circular portion, the overall depth of a standard egg shaped section, is A. D B. 1.25 D C. 1.5 D D. 1.75 D
Last Answer : ANS: C
Description : If the side of a square sewer is 1000 mm, the diameter of a hydraulically equivalent circular section, is A. 1045 mm B. 1065 mm C. 1075 mm D. 1095 mm
Last Answer : ANS: D
Description : If D is the diameter of a circular sewer and D’ is the top horizontal diameter of an equivalent egg shaped section, the relationship which holds good, is A. D’ = 0.64 D B. D’ = 0.74 D C. D’ = 0.84 D D. D’ = 0.94 D
Description : The ratio of the diameter of a circular section and the side of a square section hydraulically equivalent, is A. 1.095 B. 1.085 C. 1.075 D. 1.065
Description : If is the diameter of upper circular portion, the overall depth of New Egg shaped sewer section, is A. 1.250 D B. 1.350 D C. 1.425 D D. 1.625 D
Description : The ratio of the section modulus of a square section of side B and that of a circular section of diameter D, is (A) 2 /15 (B) 3 /16 (C) 3 /8 (D) /16
Last Answer : (B) 3 /16
Description : The discharge through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times
Last Answer : Answer: Option D
Description : The velocity through a channel of circular section will be maximum when the depth of water is __________ the diameter of the circular channel. (A) 0.34 times (B) 0.67 times (C) 0.81 times (D) 0.95 times
Last Answer : Answer: Option C
Description : If At is the area of steel cross-section, t is working stress, L is width of road and W is weight of slab per square metre, the spacing of the tie bars for a longitudinal joint, is (A) (100 At × t)/WL (B) 100 At/tWL (C) (100 WAt × t)/tL (D) 100 WL/At t
Description : A conductor with a cross-sectional area of one circular mil would have a diameter of _____________. A. 0.1 inches B. 0.01 inches C. 0.001 inches D. 0.0001 inches
Last Answer : Answer: C
Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four
Description : If AOB is a diameter of a circle [Fig. 10.8] and C is a point on the circle, then prove that AC* +BC*=AB*. -Maths 9th
Last Answer : Solution :- As, ∠ C = 90° (Angle in the semicircle) ∴ AC2 + BC2 = AB2 (By Pythagoras Theorem)
Description : What steps shall be required to rotate an object about the point P1 (as shown in fig.1) and its placement such that what was at P1 is now reduced and is at P2 (as shown in fig.2). I. Translate P1 to origin II. ... (A) I,II and III (B) II,III and IV (C) I,III and IV (D) All of the above
Last Answer : Answer: Marks given to all
Description : A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its length is doubled and the den
Last Answer : A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its ... 2` C. `4 : 1` D. `1 : 4`
Description : The most efficient cross section of sewers in a separate sewerage system is A. Parabolic B. Circular C. Rectangular D. New egged
Last Answer : ANS: B
Description : The suitable cross-section of sewers to carry combined flow, is A. Circular B. Egg shaped C. Rectangular D. Horse shoe shaped
Description : The most efficient cross-section of sewers in a combined sewerage system is A. Parabolic B. Circular C. Rectangular D. New egged
Description : The cross section of flywheel arm is 1. I section 2. Rectangular 3. Elliptical 4. Circular
Last Answer : 3. Elliptical
Description : The cross-section of the flywheel arm is, (A) I section (B) Rectangular (C) Elliptical (D) Circular
Last Answer : (C) Elliptical
Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)
Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder
Description : A stream tube is that, which has __________ cross-section entirely bounded by stream lines. (A) A circular (B) Any convenient (C) A small (D) A large
Last Answer : (B) Any convenient
Description : For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5
Last Answer : (B) 1
Description : The ratio of the area of cross-section of a circular section to the area of its core, is (A) 4 (B) 8 (C) 12 (D) 16
Last Answer : (D) 16
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius
Last Answer : (C) One-quarter of the radius
Description : The areas of cross-section of a square beam and a circular beam subjected to equal bending moments, are same. (A) Circular beam is more economical (B) Square beam is more economical (C) Both the beams are equally strong (D) Both the beams are equally economical
Last Answer : (B) Square beam is more economical
Description : The following assumption is not true in the theory of pure torsion: (A) The twist along the shaft is uniform (B) The shaft is of uniform circular section throughout (C) Cross- ... , which is plane before twist remains plane after twist (D) All radii get twisted due to torsion
Last Answer : (D) All radii get twisted due to torsion
Description : Circular cross section machine parts which are symmetrical about the axis of rotation are made by hot (A) Piercing (B) Spinning (C) Drawing (D) Extrusion
Last Answer : Option B
Description : A furrow cross-section in a country plough is commonly a) Circular b) Triangular c) Rectangular d) Trapezoidal
Last Answer : ans b
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius
Last Answer : (c) One-quarter of the radius
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above
Last Answer : a. circular cross-section
Description : In the circuit shown in Fig. 4.67, the resistance of the ammeter A is negligible and that of thevoltmeter V is very high. When the switch S is open, t
Last Answer : In the circuit shown in Fig. 4.67, the resistance of the ammeter A is negligible and that of ... internal resistance of the cell (iii) value of R.