Description : For spinning viscose rayon, the extrusion spinnerettes are made of (A) Platinum or gold alloys (B) High carbon steel (C) Aluminium (D) Nickel
Last Answer : (A) Platinum or gold alloys
Description : Earing is a defect found in steels after the following metal working operation. (A) Extrusion (B) Rolling (C) Deep drawing (D) Wire drawing
Last Answer : (C) Deep drawing
Description : When a body moves round a fixed axis it will have a.A motion of rotation and translation b.A circular motion c.A rotary motion d.A translatory motion e.A swinging motion
Last Answer : b. A circular motion
Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300
Last Answer : (C) 350-400
Description : All thermoplastic, thermosetting & elastic materials can be processed in a extrusion machine, however it cannot be used for the production of plastic (A) Filaments (B) Pipes (C) Buckets (D) Tubings
Last Answer : (C) Buckets
Last Answer : that Line Any Balanced Objects Or To the figure Two Symmetrical In part Divided By That's it Symmetrical Line. Such as : circle Diameter.
Description : In case of laminar flow of fluid through a circular pipe, the (A) Shear stress over the cross-section is proportional to the distance from the surface of the pipe (B) Surface of velocity distribution is a ... occurs at a radial distance of 0.5 r from the centre of the pipe (r = pipe radius)
Last Answer : (B) Surface of velocity distribution is a paraboloid of revolution, whose volume equals half the volume of circumscribing cylinder
Description : A stream tube is that, which has __________ cross-section entirely bounded by stream lines. (A) A circular (B) Any convenient (C) A small (D) A large
Last Answer : (B) Any convenient
Description : For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5
Last Answer : (B) 1
Description : The moment of inertia of a hollow circular section whose external diameter is 8 cm and interial diameter is 6 cm about the axis passing through its centre is a.66.8 cm4 b.137.5 cm4 c.550 cm4 d.33.4 cm4 e.275 cm4
Last Answer : b. 137.5 cm4
Description : The M.I. of hollow circular section about a central axis perpendicular to section as compared to its M.I. about horizontal axis is (A) Same (B) Double (C) Half (D) Four times
Last Answer : (B) Double
Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular
Last Answer : b) Transverse loads and couples
Description : In a synchronous machine, if the field flux axis ahead of the armature field axis in the direction of rotation, the machine is operating as (1) synchronous motor (2) synchronous generator (3) asynchronous motor (4) asynchronous generator
Last Answer : In a synchronous machine, if the field flux axis ahead of the armature field axis in the direction of rotation, the machine is operating as synchronous generator
Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None
Last Answer : (a) σt = σc
Description : Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None
Last Answer : (d) None
Description : What do you call it when earth is spinning on its axis?
Last Answer : You would say that the Earth is revolving.
Description : Which of the following is an example of simple harmonic motion? (1) Earth spinning on its axis (2) Simple pendulum motion (3) Bali bouncing on floor (4) Motion of a ceiling fan
Last Answer : (2) Simple pendulum motion Explanation: When a body moves about a mean position in such a way that the acceleration is proportional to the displacement and is always directed towards the mean ... to execute a simple harmonic motion. The motion of a simple pendulum falls under this category.
Description : In satellite communications, what means of attitude control is using the angular momentum of the spinning body to provide the roll and yaw stabilization? A. Spin stabilization B. Radial stabilization C. Three-axis stabilization D. Station keeping
Last Answer : A. Spin stabilization
Description : Which of the following is an example of simple harmonic motion? (1) Earth spinning on its axis (2) Simple pendulum motion (3) Ball bouncing on floor (4) Motion of a ceiling fan
Last Answer : Simple pendulum motion
Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above
Last Answer : (c) 15 percent
Description : In Fig. the circular cross-section of tunnel is shown. A 100 W almp is lighted at the heighest point S. The diameter of the tunnel is 2m. Compare the
Last Answer : In Fig. the circular cross-section of tunnel is shown. A 100 W almp is lighted at the heighest point ... lowest point P and the point Q of the tunnel.
Description : A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its length is doubled and the den
Last Answer : A metal wire of circular cross-section has a resistance `R_(1)`. The wire is now stretched without breaking, so that its ... 2` C. `4 : 1` D. `1 : 4`
Description : If is the diameter of upper circular portion, the area of cross-section of a standard egg shaped sewer, is A. D² B. D² C. D² D. D²
Last Answer : ANS: A
Description : The most efficient cross section of sewers in a separate sewerage system is A. Parabolic B. Circular C. Rectangular D. New egged
Last Answer : ANS: B
Description : The suitable cross-section of sewers to carry combined flow, is A. Circular B. Egg shaped C. Rectangular D. Horse shoe shaped
Description : The most efficient cross-section of sewers in a combined sewerage system is A. Parabolic B. Circular C. Rectangular D. New egged
Description : The cross section of flywheel arm is 1. I section 2. Rectangular 3. Elliptical 4. Circular
Last Answer : 3. Elliptical
Description : The cross-section of the flywheel arm is, (A) I section (B) Rectangular (C) Elliptical (D) Circular
Last Answer : (C) Elliptical
Description : The ratio of the area of cross-section of a circular section to the area of its core, is (A) 4 (B) 8 (C) 12 (D) 16
Last Answer : (D) 16
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius
Last Answer : (C) One-quarter of the radius
Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0
Last Answer : (B) 12.88
Description : The areas of cross-section of a square beam and a circular beam subjected to equal bending moments, are same. (A) Circular beam is more economical (B) Square beam is more economical (C) Both the beams are equally strong (D) Both the beams are equally economical
Last Answer : (B) Square beam is more economical
Description : The following assumption is not true in the theory of pure torsion: (A) The twist along the shaft is uniform (B) The shaft is of uniform circular section throughout (C) Cross- ... , which is plane before twist remains plane after twist (D) All radii get twisted due to torsion
Last Answer : (D) All radii get twisted due to torsion
Description : A furrow cross-section in a country plough is commonly a) Circular b) Triangular c) Rectangular d) Trapezoidal
Last Answer : ans b
Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius
Last Answer : (c) One-quarter of the radius
Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0
Last Answer : (b) 12.88
Description : A hollow prismatic beam of circular section is subjected to a torsional moment. The maximum shear stress occurs at (a) inner wall of cross section (b) middle of thickness (c) outer surface of shaft (d) none of these
Last Answer : (c) outer surface of shaft
Description : The ratio of maximum shear stress to average shear stress is 4/3 in _______ a. circular cross-section b. rectangular cross-section c. square cross-section d. all of the above
Last Answer : a. circular cross-section
Description : Plastic tubes & pipes are generally made by __________ moulding. (A) Injection (B) Transfer (C) Extrusion (D) Compression
Last Answer : (C) Extrusion
Description : Tyres are made by (A) Injection moulding (B) Extrusion (C) Rotational moulding (D) Compression moulding
Last Answer : (C) Rotational moulding
Description : In a drilling process, the metal is removed by both shearing & extrusion. General purpose drills are made of (A) Stainless steel (B) Mild steel (C) High speed steel (D) High carbon steel
Last Answer : (C) High speed steel
Description : A liquid flows through a capillary tube. Then the velocity of the liquid is (a) Maximum at the walls of the tubs (b) Constant at all points in the cross section of the tube (c) Maximum along the axis of the tube (d) Independent of the pressure-head
Last Answer : Ans:(c)
Description : Pick up the correct statement from the following: (A) For channels, the shear centre does not coincide its centroid (B) The point of intersection of the bending axis with the cross section ... shear centre coincides with the centroid of the cross section of the beam (D) All the above
Last Answer : (D) All the above
Description : The neutral axis of a beam cross-section must (A) Pass through the centroid of the section (B) Be equidistant from the top of bottom films (C) Be an axis of symmetry of the section (D) None of these
Last Answer : (A) Pass through the centroid of the section
Description : When a rectangular beam is loaded transversely, the maximum compressive stress develops on (A) Bottom fibre (B) Top fibre (C) Neutral axis (D) Every cross-section
Last Answer : (B) Top fibre
Description : The intensity of direct longitudinal stress in the cross-section at any point distant r from the neutral axis, is proportional to (A) r (B) 1/r (C) r2 (D) 1/r²
Last Answer : (A) r
Description : Compression members always tend to buckle in the direction of (a) Vertical axis (b) Horizontal axis (c) Minimum cross-section (d) Least radius of gyration
Last Answer : (d) Least radius of gyration
Description : The graphical representation of variation of axial load on y axis and position of cross section along x axis is called as _____ (a) Bending moment diagram (b) Shear force diagram (c) Stress-strain diagram (d) Trust diagram
Last Answer : (d) Trust diagram
Description : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole) (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents
Last Answer : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole) has d -axis current only