Describe the terms facing and hearting in stone masonry.

Describe the terms facing and hearting in stone masonry.
by

1 Answer

Answer :

i) Facing – The material which is used in the face of the wall is known as facing.

ii) Hearting – The portion of the wall between the facing and backing is known as the hearting.
by

Related questions

Define facing, backing, hearting and Through stone with neat sketch.

Description : Define facing, backing, hearting and Through stone with neat sketch.

Last Answer : Facing: The material used in the face of the wall is known as facing. Backing: The material used in the back of the wall is known as backing. Hearting: The inner portion of the wall ... A header stone having length equal to wall width is placed across the wall casted through stone.

Describe any eight characteristics of good stone masonry.

Description : Describe any eight characteristics of good stone masonry. 

Last Answer : The requirements of good stone masonry are as follows:- 1. The stones to be used for stone masonry should be hard, tough & durable. 2. The stone should be properly dressed as per the ... constructed perfectly in plumb. 11. The exposed joints of the masonry should be properly pointed by mortar.

Differentiate between brick masonry and stone masonry

Description : Differentiate between brick masonry and stone masonry

Last Answer : Sr. no. Brick masonry Stone masonry 1 It is cheaper than stone masonry It is stronger than Brick masonry 2 It is cheaper in places where clay is available It is ... easy to apply any finishing to Brick surface. It is difficult to apply any finishing to stone surface

Compare stone masonry construction with brick masonry construction.

Description : Compare stone masonry construction with brick masonry construction.

Last Answer : STONE MASONRY  BRICK MASONRY 1. Stone masonry is stronger and more durable than brick masonry 1. Brick masonry is less stronger and less durable than stone masonry. 2. ... other hand is considered unsuitable in the construction of piers, docks, dams and other marine structure.

State the precautions to be observed in stone masonry construction.

Description : State the precautions to be observed in stone masonry construction.

Last Answer : Following are the precautions to be observed in stone masonry construction: 1. Stone used in masonry should be well seasoned, hard, tough, uniform in texture. 2. Stones used should be free from ... on the natural bed. 10. The exposed joints of the masonry should be properly pointed by mortar.

Compare brick masonry and stone masonry used in building construction.

Description : Compare brick masonry and stone masonry used in building construction.

Last Answer : Sr. No. Brick Masonry Stone Masonry 1 It is less stronger than stone masonry. It is stronger than brick masonry. 2 It is cheaper in places where clay is available ... is used Double scaffolding is used 12 Plastering is required  Plastering is not required

Describe any four forms of ‘Rubble Masonry’ with sketches.

Description : Describe any four forms of ‘Rubble Masonry’ with sketches.

Last Answer : 1) Dry rubble masonry: - In dry rubble masonry, dressed or undressed stones are used without mortar. Bigger pieces of stones are arranged at the bottom and smaller pieces of stones are used at the top. ... should not exceed 13 mm. the stone used in this masonry should be of uniform color.  

The type of pointing in which upper side of mortar joints is kept about 12 mm inside the face of the masonry and bottom is kept flushed with face of wall, is (A) Truck pointing (B) Recessed pointing (C) Struck pointing (D) Grooved pointing

Description : The type of pointing in which upper side of mortar joints is kept about 12 mm inside the face of the masonry and bottom is kept flushed with face of wall, is (A) Truck pointing (B) Recessed pointing (C) Struck pointing (D) Grooved pointing

Last Answer : Option C

Pick up the correct statement from the following: (A) A mortar joint having a concave finishing in brick masonry, is called keyed joint (B) A mortar joint projecting beyond the face of a masonry wall, is called tucked joint (C) A mortar joint having a recess in it, is called ruled joint (D) All the above

Description : Pick up the correct statement from the following: (A) A mortar joint having a concave finishing in brick masonry, is called keyed joint (B) A mortar joint projecting beyond the face of a masonry wall, is ... (C) A mortar joint having a recess in it, is called ruled joint (D) All the above

Last Answer : Option D

As a ‘Supervisor’, state precautionary measures you will observe while constructing brick masonry, along with their reasons.

Description : As a ‘Supervisor’, state precautionary measures you will observe while constructing brick masonry, along with their reasons.

Last Answer : Following Precautionary measures are to be observe as a supervisor while constructing brick masonry: 1. Bricks should be as per the specification. The bricks should be well burnt, reddish in colour, sound and hard ... is used and for a period of about one to two weeks, if cement mortar is used.

Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Description : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Last Answer : Draw a neat labeled sectional view showing different components of building from foundation to parapet, for a load bearing brick masonry wall.

Define the terms Newel post and Headroom in vertical communication.

Description : Define the terms Newel post and Headroom in vertical communication.

Last Answer : Newel post : This is the vertical member which is placed at the ends of flights to connect the end of strings and hand rail.  Headroom : The vertical distance between the nosing of one flight and bottom of flight immediately above is known as the headroom.

Define the terms substructure and superstructure used in building construction.

Description : Define the terms substructure and superstructure used in building construction.

Last Answer : Substructure: - A part of structure lying below the ground surface is known as substructure.  Superstructure: - A part of structure lying above the ground surface is called superstructure.

Describe the procedure of water proofing used in slabs stating its importance in building construction.

Description : Describe the procedure of water proofing used in slabs stating its importance in building construction.

Last Answer : Following is the stepwise procedure effectively applied in treatment of brick bat coba.  1 All existing treatment or coating on roof slab top is initially removed and surface is cleaned by hard wire brush ... surface is marked with 300 mm false squares The curing is done on next day. 

Describe the procedure for carrying out the ‘Plastering’ in cement mortar in two coats.

Description : Describe the procedure for carrying out the ‘Plastering’ in cement mortar in two coats.

Last Answer : The mix ratio of mortar in case of cement plastering depends upon the nature of the work to be plastered.  For rich plastering work at sensitive places (e.g. in side bathrooms, W.C. etc.), 1:3 ... help of a steel float. It is then allowed to set for 2 days and cured for more than 7 days.

Describe the procedure for layout of load bearing structure by center – line method.

Description : Describe the procedure for layout of load bearing structure by center – line method.

Last Answer : 1. From the plan (fig 1), the center line of the walls are calculated. Then the center lines of the rooms are set out by setting perpendiculars in the ratio 3:4:5. Suppose the corner points ... lime or by with furrow with spade. 6. A theodolite should be used for accurate center line marking. 

Describe in brief with neat sketch: i) English bond ii) Flemish bond

Description : Describe in brief with neat sketch: i) English bond ii) Flemish bond

Last Answer : English bond : The Bond with alternate courses of headers and stretchers with a closer placed next to quoin header is called as the English Bond. Points Should be Remembered for English bond: 1. A ... . 4. Flemish Bond is slightly economical as a number of brick bats can be used.

Describe the procedure of laying a floor finish on a newly constructed slab.

Description : Describe the procedure of laying a floor finish on a newly constructed slab.

Last Answer : 1. Slab is cleared off from loose mortar deposited during plaster work and level the surface. 2. Chalk out the marking on wall @ 0.6 m above the slab surface in one level. 3. Construct mortar dots at four ... and lay the tile in line and level. 8. Repeat point no 7 procedure up to door corner.

Raft foundation are generally preferred to when the area required for individual footing, is more than (A) 25% to total area (B) 30% of total area (C) 40% to total area (D) 50% of total area

Description : Raft foundation are generally preferred to when the area required for individual footing, is more than (A) 25% to total area (B) 30% of total area (C) 40% to total area (D) 50% of total area

Last Answer : Option D

Pick up the correct statement from the following: (A) Isolated footing is provided under column to transfer the load safely to soil bed (B) Column footings may have steps or projections in the concrete base (C) Heavily loaded column base must be provided steel reinforcement in both directions (D) All the above

Description : Pick up the correct statement from the following: (A) Isolated footing is provided under column to transfer the load safely to soil bed (B) Column footings may have steps or projections in the ... ) Heavily loaded column base must be provided steel reinforcement in both directions (D) All the above

Last Answer : Option D

The pile provided with one or more bulles in its vertical shaft, is generally known as (A) Under-ream pile (B) Friction pile (C) Bearing pile (D) Sheet pile

Description : The pile provided with one or more bulles in its vertical shaft, is generally known as (A) Under-ream pile (B) Friction pile (C) Bearing pile (D) Sheet pile

Last Answer : Option A

The Auger borings are not common (A) In soils that require lateral support (B) In cohesive soils (C) In soft soils (D) None of the above

Description : The Auger borings are not common (A) In soils that require lateral support (B) In cohesive soils (C) In soft soils (D) None of the above

Last Answer : Option A

Pitched and sloping roofs are suitable for (A) Coastal regions (B) Plain regions (C) Covering large areas (D) All of the above

Description : Pitched and sloping roofs are suitable for (A) Coastal regions (B) Plain regions (C) Covering large areas (D) All of the above

Last Answer : Option A

A wall constructed to resist the pressure of an earth filling, is called (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall

Description : A wall constructed to resist the pressure of an earth filling, is called (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall

Last Answer : Option A

Pick up the correct statement from the following: (A) The pile driven in sand is called sand pile (B) The drilled hole filled with sand is called sand pile (C) The sand piles are used for bearing purposes (D) None of these

Description : Pick up the correct statement from the following: (A) The pile driven in sand is called sand pile (B) The drilled hole filled with sand is called sand pile (C) The sand piles are used for bearing purposes (D) None of these

Last Answer : Option A

The position of a brick when laid on its side 9 cm × 9 cm with its frog in the vertical plane, is called (A) Brick on edge (B) Brick on end (C) Brick on bed (D) Brick held vertically

Description : The position of a brick when laid on its side 9 cm × 9 cm with its frog in the vertical plane, is called (A) Brick on edge (B) Brick on end (C) Brick on bed (D) Brick held vertically

Last Answer : Option B

The foundation which consists of a thick reinforced cement slab covering whole area to support heavy concentrated structural loads, is known as (A) Combined footing (B) Strap footing (C) Raft footing (D) None of these

Description : The foundation which consists of a thick reinforced cement slab covering whole area to support heavy concentrated structural loads, is known as (A) Combined footing (B) Strap footing (C) Raft footing (D) None of these

Last Answer : Option C

For different layers of cement concrete floor. Pick up the incorrect statement from the following: (A) The lowest layer consists of consolidated ground (B) A 10 cm thick clean sand is laid on consolidated ground (C) A 10 cm lime concrete (1 : 4 : 8) is laid on clean sand (D) A 10 cm thick cement concrete (1 : 2 : 4) is laid on top layer

Description : For different layers of cement concrete floor. Pick up the incorrect statement from the following: (A) The lowest layer consists of consolidated ground (B) A 10 cm thick clean sand is laid on consolidated ground (C) ... sand (D) A 10 cm thick cement concrete (1 : 2 : 4) is laid on top layer

Last Answer : Option D

Higher pitch of the roof (i) Results in stronger roof (ii) Results in weaker roof (iii) Requires more covering material (iv) Requires less covering material The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : Higher pitch of the roof (i) Results in stronger roof (ii) Results in weaker roof (iii) Requires more covering material (iv) Requires less covering material The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Option A

A wall constructed with stones to protect slopes of cuttings in natural ground from the action of weathering agents, is called (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall

Description : A wall constructed with stones to protect slopes of cuttings in natural ground from the action of weathering agents, is called (A) Retaining wall (B) Breast wall (C) Buttress (D) Parapet wall

Last Answer : Option B

Pick up the correct statement from the following: (A) D.P.C. should be continuous (B) D.P.C. should be of good impervious material (C) D.P.C. may be horizontal or vertical (D) All the above

Description : Pick up the correct statement from the following: (A) D.P.C. should be continuous (B) D.P.C. should be of good impervious material (C) D.P.C. may be horizontal or vertical (D) All the above

Last Answer : Option D

The inclined surface of an abutment to receive the arch, is known as (A) Skew back (B) Soffit (C) Spandril (D) Haunch

Description : The inclined surface of an abutment to receive the arch, is known as (A) Skew back (B) Soffit (C) Spandril (D) Haunch

Last Answer : Option A

The pile which supports the load due to friction between pile face and surrounding soil, is generally known as (A) Bearing pile (B) Friction pile (C) Sheet pile (D) Battered pile

Description : The pile which supports the load due to friction between pile face and surrounding soil, is generally known as (A) Bearing pile (B) Friction pile (C) Sheet pile (D) Battered pile

Last Answer : Option B

The form work from the slabs excluding props, can be removed only after (A) 1 day (B) 4 days (C) 7 days (D) 14 days

Description : The form work from the slabs excluding props, can be removed only after (A) 1 day (B) 4 days (C) 7 days (D) 14 days

Last Answer : Option B

Cast iron piles (A) Are suitable for works under sea water (B) Resist shocks or vibrations (C) Are suitable for use as batter piles (D) Are useful for heavy vertical loads

Description : Cast iron piles (A) Are suitable for works under sea water (B) Resist shocks or vibrations (C) Are suitable for use as batter piles (D) Are useful for heavy vertical loads

Last Answer : Option D

The form work from the slabs excluding props, can be removed only after (A) 1 day (B) 4 days (C) 7 days (D) 14 days

Description : The form work from the slabs excluding props, can be removed only after (A) 1 day (B) 4 days (C) 7 days (D) 14 days

Last Answer : Answer: Option B

Cast iron piles (A) Are suitable for works under sea water (B) Resist shocks or vibrations (C) Are suitable for use as batter piles (D) Are useful for heavy vertical loads

Description : Cast iron piles (A) Are suitable for works under sea water (B) Resist shocks or vibrations (C) Are suitable for use as batter piles (D) Are useful for heavy vertical loads

Last Answer : Answer: Option D

Explain the requirements of good formwork with names and materials proposed for beam of size 300 X 450 mm with neat labeled sketch.

Description : Explain the requirements of good formwork with names and materials proposed for beam of size 300 X 450 mm with neat labeled sketch.  

Last Answer : Requirements of good formwork:- 1. It should be adequately strong to withstand an extensive variety of dead and live loads. For instance, self-weight, weight of reinforcement, weight of wet concrete, loads of ... of concreting. 8. It should be lightweight. 9. It should be easy to remove.

Explain raft foundation with neat sketch and explain its suitability.

Description : Explain raft foundation with neat sketch and explain its suitability. 

Last Answer : Raft Footing: It is suitable where ground is soft. Clayey or marshy having low bearing capacity, and where sub soil water conditions are uncertain. The raft foundation is also used to reduce settlement below highly compressible soils

Define shoring. Enlist types of shoring. Explain any one type with neat sketch.

Description : Define shoring. Enlist types of shoring. Explain any one type with neat sketch.

Last Answer : Shoring:- Shoring is the construction of a temporary structure to support temporarily an unsafe structure. These support walls laterally. Shoring can be used when walls bulge out, when walls crack due to ... of the structure above and transfer same to the ground on firm foundation below. 

Suggest relevant type of foundation with sketch for educational building on black cotton soil with justification.

Description : Suggest relevant type of foundation with sketch for educational building on black cotton soil with justification. 

Last Answer : Black cotton soil- Pile foundation. In case the depth of black cotton soil is more, the following type of foundation may be provided 1. Strip or pad foundation 2. Pier foundation with ... of expansive soil. They are bored cast-in-situ concrete piles having bulb shaped enlarged base.

State any four precautions to be taken while plastering.

Description : State any four precautions to be taken while plastering.

Last Answer : i. Before application of the plastering, the surface must be clean and free of dirt, oil, or other elements which may interfere with bonding. ii. Smooth or non-absorbent surfaces should be prepared. iii. ... or vertical line at the end of the day or if work requires to be suspended for any reason.

Suggest precaution to be taken during demolition.

Description : Suggest precaution to be taken during demolition.

Last Answer : Following precaution to be taken during demolition: 1. Complete evacuation of building including pets and other animals. 2. Careful study of the building. 3. Emptying of surrounding area. ... explosive. 8.Action plan already prepared if explosion goes wrong or only partial explosion occur.

Explain the procedure of preparation of surface along with the method of application of color wash paint on the wall.

Description : Explain the procedure of preparation of surface along with the method of application of color wash paint on the wall.

Last Answer : The correct preparation of surface plays an important role in preserving the properties and life of the paint. For these the procedure is as follows: 1.If the receiving surface is rough, it should be made smooth ... of color wash paint on the wall. 1.By Brushing. 2.By Spraying. 3. By Rollers.

Define substructure and superstructure. Give their components also.

Description : Define substructure and superstructure. Give their components also.

Last Answer : Substructure: - A part of structure lying below the ground surface is known as substructure. components of substructure :-1) foundation Superstructure: - A part of structure lying above the ground surface is called ... Beam 6) Roof 7) Doors 8) Windows 9) Lintel 10)Sill 11) Staircase 12) Parapet. 

Explain the types of probable cause of non-structural cracks observed in building construction along with preventive measures for any one of crack.

Description : Explain the types of probable cause of non-structural cracks observed in building construction along with preventive measures for any one of crack. 

Last Answer : Cause of cracks:   Cause # 1. Movement Due To Creep: Creep of a material is defined as the property due to which the material continues to deform with time under sustained stress. ... contraction and slip joints at appropriate location. Painting top roof with reflective finish such as white wash.

Explain four defects in plastering with neat sketch.

Description : Explain four defects in plastering with neat sketch.

Last Answer : Following are the defects in plastering: 1) Blistering of plastered surface: it is the defect in which small patches of plaster are swelled out from the plastered surface. 2 ... defect in which there is complete dislocation of some portion of plastered surface which forms the patches. 

State any four precautions to be taken while marking layout on ground.

Description : State any four precautions to be taken while marking layout on ground.

Last Answer : The necessary precaution to be taken while marking layout on ground are as follows 1. All vertical wooden post should be firmly fixed into the ground with concrete and curing should be done to the ... the face line or center line correctly. 19. Use proper or correct plumb bob for centering. 

Difference between load bearing structure and framed structure

Description : Difference between load bearing structure and framed structure

Last Answer : Description Load bearing structure Framed Structure Sub soil condition Suitable only when hard strata are available at shallow depth Suitable for any type of soil Number of storey's 3 ... The frame can be RCC( beam/ Column) frame, I- Section Steel frame, Wood frame etc.