how to convert kw into btus

1 Answer

Answer :

1 kW = 3412.142 BTU/hr

Related questions

Description : How do I calculate what size air conditioner (in BTUs) I need according to my apartment's square footage?

Last Answer : answer:Will also depend on insulation, windows, and locale (BTU requirement in San Francisco, for instance, is substantially lower than Phoenix, Arizona). However, I can't seem to find the book with the general formula's in it... sorry!

Description : How many BTU's do you need?

Last Answer : answer:Most gas ranges have four burners, measured in British thermal units per hour (Btu/hr.): one or two medium-output burners (about 9,000 Btu/hr.), a small burner (about 5,000 Btu/hr.), and one ... circulating the air in the oven. I highly recommend one, if you do a lot of baking. Good Luck! R

Description : How many Btus of heat are removed per hour when the water at a flow rate of 10 pounds per minute is cooled 15 degrees Fahrenheit (Water weighs 8.33 pounds per gallon)?

Last Answer : Feel Free to Answer

Description : How do I determine how many BTUs I need per foot for each room when purchasing portable heaters?

Last Answer : It depends on the climate and how well your home is insulated.A good rule of thumb is about 20 BTUs per square foot.

Description : What propane heater has the most BTU's?

Last Answer : Any industrial propane heater will have thousands of BTU's, but will cost a small fortune. Find one in the middle that works well for you.

Description : How many BTUs do I need to cool a 20x9 room?

Last Answer : A romm 20x9 is 180 square feet. You will need 5000 to 6000 BTUs for this.

Description : What air conditioner has the most BTU's?

Last Answer : With 28,000 BTUs, the Friedrich SL28L30* has the most BTUs.

Description : How many BTU's would I need for a 15 by 20 foot room?

Last Answer : 5000 BTU's should work for a room that size.

Description : How can I determine how many BTUs I need for an air conditioner?

Last Answer : A small room is about 5,000 BTUs. Most people don't have a room that would require more than 10,000 BTUs.

Description : What are the BTU's for this microwave?

Last Answer : The Electrolux EI30MH55GS Microwave oven can be mounted over high-performance cooktops, with up to 56,000 BTU of total heat output.

Description : How many BTU's should a heat pump have to effective heat a 200 sq. foot room?

Last Answer : It depends on your enviornment. A 36,000 BTU unit will probably work just fine. 36,000 btu's would heat a 1,000 square foot room. or more.

Description : How many BTUs can a gallon of water store?

Last Answer : You can assume two temperatures, and calculate the amount of energy required to heat the water from one temperature to the other. Then convert that to BTU.

Description : Which of the following statements are true? i) reactive current is necessary to build up the flux for the magnetic field of inductive devices ii) some portion of reactive current is converted into work iii) the cosine of angle ... called power factor a) i & iv b) ii & iii c) i & iii d) iii & iv

Last Answer : a) i & iv

Description : why do you use the highest voltage insted of actual voltage to find kw?

Last Answer : Your question is unclear. Are you trying to compare kw with kva?

Description : The power of a locomotive is 315 kW and the total weight of the train is 2000 kN. If the track resistance is 15 N per kN, the maximum speed that the locomotive can attain on level track will be a.43 kmph b.83 kmph c.103 kmph d.107 dynes e.38 kmph

Last Answer : e. 38 kmph

Description : Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Last Answer : b. 163.5 KW

Description : The power of a locomotive is 315 kW and the total weight of the train is 2000 kN. If the track resistance is qN per kN, the maximum speed that the locomotive can attain on level track will be a.103 kmph b.83 kmph c.107 dynes d.43 kmph e.63 kmph

Last Answer : e. 63 kmph

Description : Which of the following is not a unit of energy? a.Joule b.kW c.N-m d.Electron volt e.Watt-hour

Last Answer : b. kW

Description : Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW

Last Answer : c. 6.81 KW

Description : 2. An electric oven of 2 kW power rating is operated in a domestic electric circuit (220 V) that has a current rating of 5 A. What result do you expect? Explain. -Physics-10

Last Answer : The current drawn by the electric oven can be calculated using the formula P = V × I I = P/V Substituting the values, we get I = 2000 W/220 V = 9.09 A The current drawn by the electric oven is 9.09 A which exceeds the safe limit of the circuit. This causes the fuse to melt and break the circuit.

Last Answer : The full form of KW Kilowatt.

Description : How can I calculate how many kw is 1 amp?

Last Answer : This can't just be converted because one is the current and the other is power. It's almost like asking how many meters a liter is. :) It also matters here how many volts, that is, at what voltage we ... in 1 amp' description = ''] https:///wp-content/uploads/2017/03/amper-watt.jpg [/ img]        

Description : How many light bulbs would I have to turn on 100 watts to eat 1 KW per hour?

Last Answer : 1 kW = 1000 W Come on purpose - how many times 100 is 1000? (rofl)

Description : A reaction develop nuclear energy at the rate of `3 xx 10^(4) kW`. How many atoms of `.^(215)U` undergo fission per second? How much `.^(235)U` is bur

Last Answer : A reaction develop nuclear energy at the rate of `3 xx 10^(4) kW`. How many atoms of `.^(215)U` ... constant is `6.023 xx 10^(26)` per kg mole)

Description : An electric immersion heater of `1.08 kW` is immersed in water . After it has reaches a temperature of `100^(@)C` , how much time will be required to

Last Answer : An electric immersion heater of `1.08 kW` is immersed in water . After it has reaches a temperature of `100^(@)C` ... 50 s B. 420 s C. 105 s D. 105 s

Description : What all does FPL meters measure kw/kwh and what else?

Last Answer : Florida Power & Light Company only measures kw/kwh (kilowatt per kilowatt hour). However, your bill will include a standard customer charge to cover general maintenance and administration fees. Fuel charges, ... and taxes are also included in the bill. These charges are based on your electric usage.

Description : A blender has a power of 0.3 kW. It is used to make a fruit smoothie, which takes 50 seconds. How much energy is used Give your answer in kilojoules.kJ?

Last Answer : 15 KJ

Description : A 40 kW engine has a mechanical efficiency of 80 %. If the frictional power is assumed to be constant with load, what is the approximate value of the mechanical efficiency at 50 % of the rated load? (a) 45% (b) 55 % (c) 65% (d) 75%

Last Answer : Ans :c

Description : An engine produces 10 kW brake power while working with a brake thermal efficiency of 30%. If the calorific value of the fuel used is 40000 kJ/kg, then what is the fuel consumption? (a) 1.5 kg/hour (b) 3 kg/hour (c) 0.3 kg/hour (d) 1 kg/hour

Last Answer : Ans :b

Description : In a morse test for a 2 cylinder, 2 S SI engine, the brake power was 9 kW. Whereas the brake power of individual cylinders with spark cut off were 4.25 kW and 3.75 kW. The mecheffic of the engine is (a) 90% (b) 80% (c) 45.5% (d) 52.5%

Last Answer : Ans :a

Description : Which of the following statements is correct concerning the motor performance curves and data table shown in the illustration? EL-0006 A. The motor RPM at full load is 1737 RPM. B. The motor draws 12.62 kw ... If the motor was developing 10 HP its power factor would be 0.92. D. All of the above.

Last Answer : Answer: D

Description : A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by _____________. A. 38.525 kw B. 116.91 kw C. 155.88 kw D. 194.85 kw

Last Answer : Answer: A

Description : A vessel is equipped with two ship's service generators. Generator #1 is rated at 900 kw and generator #2 is rated at 600 kw. During parallel operation, with a hotel load of 1,000 kw, what should be the kw load on generator #2? A. 100 kw B. 400 kw C. 500 kw D. 600 kw

Last Answer : Answer: B

Description : A turbogenerator has a rated output of 1200 KW at 60 Hertz, with a no load frequency of 61.5 Hertz. What is its speed droop? A. 1.03% B. 1.50% C. 2.44% D. 2.50%

Last Answer : Answer: D

Description : A circuit breaker for a 300 KW alternator is rated at 470 amperes of full continuous load. The amount of overcurrent allowed is 125%. Which of the following conditions will trip the breaker? A. ... 10 minutes. C. Momentary starting load of 550 amperes. D. Sustained current flow of 590 amperes.

Last Answer : Answer: D

Description : A three-phase alternator operates at 450 volts with a power factor of 0.8. If the ammeter indicates 250 amperes, what should be the KW meter reading? A. 90.00 KW B. 127.27 KW C. 155.70 KW D. 194.85 KW

Last Answer : Answer: C

Description : A three-phase alternator is developing 300 amps, with a 0.8 power factor, at 450 volts. The true indicated power on the kilowatt meter, located on the main switchboard, will be ____________. A. 133 kw B. 155 kw C. 187 kw D. 212 kw

Last Answer : Answer: C

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Last Answer : Answer: B

Description : The KW load is evenly distributed between two alternators just placed in parallel by adjusting _____________. A. a balance coil B. the governor settings C. the field excitation D. a rheostat

Last Answer : Answer: B

Description : Which is a function of the voltage regulators used with AC generators? A. To cut out generators when they are no longer required. B. To cut in additional generators automatically as ... between generators operating in parallel. D. To divide reactive current between generators operating in parallel.

Last Answer : Answer: D

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Last Answer : Answer: B

Description : If 4 kW in antenna produces 50 μV/m in a receiving antenna, a 15 kW will produce _____. A. 200 μV/m B. 10 μV/m C. 100 μV/m D. 20 μV/m

Last Answer : C. 100 μV/m

Description : A dipole antenna requires to be fed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11kW ... Gain referred to this particular dipole). A. 4.75 B. 2.6 C. 1.81 D. 4.24

Last Answer : B. 2.6

Description : Why are Alternators rated in kVA and not in kW?

Last Answer : The continuous power rating of any machine is generally defined as the power the machine or apparatus can deliver for a continuous period so that the losses incurred in the machine gives rise to a ... generator , the Alternators have only their apparent power in VA/kVA/MVA as their power rating.

Description : The product of antenna input power and the antenna power gain expressed in kW is called __. A. Effective Radiated Power (ERP) B. Effective Isotropic Radiated Power (EIRP) C. Radiated Power D. Transmit Power

Last Answer : A. Effective Radiated Power (ERP)

Description : Determine the effective radiated power of 20 kW TV broadcast transmitter whose antenna has a field gain of 2. A. 40 kW B. 80,000 watts C. 40,000 watts D. 8,000 watts

Last Answer : B. 80,000 watts

Description : A transmitter supplies 8 kW to the antenna when it is unmodulated, determine the total radiated power when modulated at 90%. A. 5 kW B. 20 kW C. 15 kW D. 8.36 kW

Last Answer : D. 8.36 kW

Description : How much is the required minimum power output of an international AM BC stations? A. 5 kW B. 30 kW C. 10 kW D. 50 kW

Last Answer : D. 50 kW

Description : The maximum power suggested by KBP on 919-1312 AM broadcast station in Metro Manila is A. 10 kW B. 20 kW C. 15 kW D. 5 kW

Last Answer : B. 20 kW

Description : A dipole antenna requires to be feed with 20 kW of power to produce a given signal strength to a particular distant point. If the addition of a reflector makes the same field strength available with an input power of 11 ... ( Gain referred to this particular dipole) A. 4.24 B. 1.81 C. 4.75 D. 2.6

Last Answer : D. 2.6