A 4 ῼ resistor carrying 2 Amp current will dissipate power equal to

by

1 Answer

Answer :

A 4 ῼ resistor carrying 2 Amp current will dissipate power equal to 16 watts.

by

Related questions

A waveguide termination having VSWR of 1.1 is used to dissipate 100 watts of power. The reflected power

Description : A waveguide termination having VSWR of 1.1 is used to dissipate 100 watts of power. The reflected power will be A) 0.2268 W B) 0.5868 W C) 0.3468 W D) 0.4568 W 

Last Answer : A waveguide termination having VSWR of 1.1 is used to dissipate 100 watts of power. The reflected power will be 0.2268 W

A long wire carrying 100 amp is placed in an external magnetic field of...

Description : A long wire carrying 100 amp is placed in an external magnetic field of 50 gauss. The wire is at right angles to the field.

Last Answer : The field is null above the wire and crowded below

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Description : Three equal resistors connected in series with a source of e m f together dissipate 10 W of power each. What will be the power dissipated if the same resistors are connected in parallel across the same source of e m f? a. 40 W b. 90W c. 100W d. 120W

Last Answer : b. 90W

Shading coils are installed on AC full-voltage starters to _____________. A. eliminate contact chatter B. dissipate opening contact arcs C. delay current build up in the holding coil D. protect the motor windings from momentary starting current overload

Description : Shading coils are installed on AC full-voltage starters to _____________. A. eliminate contact chatter B. dissipate opening contact arcs C. delay current build up in the holding coil D. protect the motor windings from momentary starting current overload

Last Answer : Answer: A

The current in a circuit with resistance in 6 amp. When an additional ...

Description : The current in a circuit with resistance in 6 amp. When an additional resistance of 4 ohms is inserted the current drops to 4 amp. The original resistance in ohms is

Last Answer : The current in a circuit with resistance in 6 amp. When an additional resistance of 4 ohms is inserted the current drops to 4 amp. The original resistance in ohms is 8.

What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Description : What is meant by the term radiation resistance for an antenna? A. The resistance in the trap coils to received signal B. An equivalent resistance that would dissipate the same amount of power as ... antenna C. The specific impedance of the antenna D. Losses in the antenna elements and feed line

Last Answer : B. An equivalent resistance that would dissipate the same amount of power as that radiated from an antenna

It is the resistance that, if it replaced the antenna, would dissipate exactly the same amount of power that the antenna radiates

Description : It is the resistance that, if it replaced the antenna, would dissipate exactly the same amount of power that the antenna radiates

Last Answer : . Radiation resistance

If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then what is the total power loss?

Last Answer : If two parallel-connected resistors dissipate 6 watts and 10 watts of power, then 16 watts is the total power loss.

If we could drop an F5 tornado in the middle of a hurricane, would that disrupt it enough to dissipate it?

Description : If we could drop an F5 tornado in the middle of a hurricane, would that disrupt it enough to dissipate it?

Last Answer : It might just be absorbed by the hurricane and make it even stronger.

Using your fingers to dissipate the foam on top of the ****: gross or not gross?

Description : Using your fingers to dissipate the foam on top of the beer: gross or not gross?

Last Answer : As long as it’s your own beer, I wouldn’t care. But keep your oily finger out of my beer.

How long does it take chlorine to dissipate from treated water?

Description : How long does it take chlorine to dissipate from treated water?

Last Answer : 24 hours should do it.

If ghosts are made of energy, then why don't ghosts entropy or dissipate?

Description : If ghosts are made of energy, then why don't ghosts entropy or dissipate?

Last Answer : answer:Ghost myths simply don't adhere to the laws of science. If they were pure energy, they would also only last a certain amount of time thanks to Newton's Law of Exponential Decay. Anyone who ... if people want to believe in ghosts, but please don't muddy the name of science in the process.

Can heat dissipate into a vacuum?

Description : Can heat dissipate into a vacuum?

Last Answer : Well, there is thermal radiation in the infrared spectra, but other than that I don’t know.

Is there a Home Remedy to eliminate or dissipate paint odor?

Description : Is there a Home Remedy to eliminate or dissipate paint odor?

Last Answer : answer:Why would you want to dissipate it? Seriously though- knowing not everyone is an artist who enjoys the smell of paint- airing out is the best method. Sprays mask it but in reality the fumes need to ... fresh paint is not in the direct path of the fan so it does not blow dust onto the surface.

When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent mechanical damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Description : When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent ... damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Last Answer : Answer: D

Select the option that is most nearly OPPOSITE in meaning to the word in BOLD. Don’t dissipate your strength on useless projects. (a) Conserve (b) Disperse (c) Dispel (d) Squander

Description : Select the option that is most nearly OPPOSITE in meaning to the word in BOLD. Don’t dissipate your strength on useless projects. (a) Conserve (b) Disperse (c) Dispel (d) Squander

Last Answer : (a) Conserve

The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ? (a) Conduction (b) Convection (c) Radiation (d) All ofthe above

Description : The heated parts of an electrical machine dissipate heat into their surroundings by which of the following modes of heat dissipation ? (a) Conduction (b) Convection (c) Radiation (d) All ofthe above

Last Answer : (d) All ofthe above

Describe the concept of virtual ground with reference to op-Amp.

Description : Describe the concept of virtual ground with reference to op-Amp.

Last Answer : Virtual ground concept:-In circuit point A is virtual ground. Figure shows inverting amplifier using op-amp. In this circuit non-inverting terminal is connected to the actual ground. Due to ... zero potential without actually grounding is known as virtual ground concept. Circuit diagram: 

Block Diagram of op-Amp

Description : Block Diagram of op-Amp

Last Answer : Block Diagram: The OP-AMP is basically a different amplifier i.e. it will amplify the voltage which is differentially present between its input terminals.  1.Input stage: The ... normally a complementary output stage. It increases the OPAMP. It also provides a low output resistance. 

In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the

Description : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the (A) applied load (B) internal compensation (C) impedance of the source (D) power dissipation in the chip

Last Answer : In a 741 Op-Amp, there is 20 dB/decade fall-off starting at a relatively low frequency. This is due to the internal compensation

In an op-amp differentiator

Last Answer : In an op-amp differentiator the amplitude of output is proportional to rate of change of input.

A crow is sitting on a conductor carrying 11,000 volts

Last Answer : It will not die because it is insulated from earth and other conductors

When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the battery amp-hour rating C. the source of power for charging should be 2.5 volts per cell D. gassing within the battery decreases when nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Description : When charging a 100 amp-hour lead-acid battery, ___________. A. the temperature of the electrolyte should not be allowed to exceed 90°F B. the charging rate should be no greater than 125% of the ... nearing full charge and it will be necessary to reduce the charging current to a low finishing rate

Last Answer : Answer: C

To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Description : To provide its unique characteristics to analog circuits, the operational amplifier is made up of a/an ______________. A. voltage amp, current amp and output amp B. input amp, power amp and output amp C. scaling amp, power amp and voltage amp D. differential amp, voltage amp and output amp

Last Answer : Answer: D

A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Description : A series circuit consists of two resistors in series. R1 = 25 ohms and R2 = 30 ohms. The circuit current is 6 amps. What is the (a) source voltage, (b) voltage dropped by each resistor, (c) total power, and (d) power used by each resistor?

Last Answer : (a) 330 volts. (b) E1 = 150 volts. E2 = 180 volts. (c) 1.98 kilowatts. (d) P1 = 900 watts. P2 = 1.08 kilowatts component but in a parallel circuit total current divides among the available paths.

What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Last Answer : 1 kilowatt.

A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Description : A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Last Answer : ANSWER: 250 WATTS

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

Assertion three infinitely long current carrying wires have equal currents and they are equally spaced. The magnitude of magnetic force on all three i

Description : Assertion three infinitely long current carrying wires have equal currents and they are equally spaced. The magnitude of magnetic force on all three i

Last Answer : Assertion three infinitely long current carrying wires have equal currents and they are equally spaced. The ... Reason Net force on wire-2 is zero.

Force per meter on two wires carrying a current of 1 A placed 1 m apart is equal to A. 6.7 × 10-11 N B. 9.0 × 109 N C. 2.0 × 10-7 N D. 3.0 × 10-4 N

Description : Force per meter on two wires carrying a current of 1 A placed 1 m apart is equal to A. 6.7 × 10-11 N B. 9.0 × 109 N C. 2.0 × 10-7 N D. 3.0 × 10-4 N

Last Answer :  2.0 × 10-7 N

Find the magnetic field intensity at the centre O of a square of the sides equal to 5m and carrying 10A of current. a) 1.2 b) 1 c) 1.6 d) 1.8

Description : Find the magnetic field intensity at the centre O of a square of the sides equal to 5m and carrying 10A of current. a) 1.2 b) 1 c) 1.6 d) 1.8

Last Answer : d) 1.8

A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Last Answer : Answer: D

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

The thickness of the layer of insulation on the conductor, in cables, depends upon (a) Reactive power (b) Power factor (c) Voltage (d) Current carrying capacity

Description : The thickness of the layer of insulation on the conductor, in cables, depends upon (a) Reactive power (b) Power factor (c) Voltage (d) Current carrying capacity

Last Answer : (c) Voltage

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

What has the most energy in its chemical bonds? a) AMP b) ADP c) ATP d) All are equal

Description : What has the most energy in its chemical bonds? a) AMP b) ADP c) ATP d) All are equal 

Last Answer : ANSWER: C -- ATP

Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:

Description : Ripple in output current of a step-down chopper feeding RLE load is maximum, when duty cycle is equal to:  (1) 1 (2) 0.5 (3) 0.75 (4) 0.33

Last Answer : Ripple in output current of step down Chopper feeding a RLE load is maximum, when duty cycle is equal to 0.5

For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Description : For practical purposes, in a simple series circuit, the source voltage will be dropped across one resistor if it has ______________. A. half the resistance of the other resistor B. a resistance equal to the other C. at least ten times the resistance of the other D. a partial short circuit

Last Answer : Answer: C

Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Description : Four equal resistors are connected in parallel, each resistor has an ohmic value of 100 ohms, what is the equivalent resistance?

Last Answer : 25 ohms

What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Last Answer : Zero.

Low volt, High Amp current?

Description : Low volt, High Amp current?

Last Answer : Imagine a car battery. They are 12-15V and are capable of delivering 600 amps - when there is a conductor with very low resistance across the terminal. (Volts / current = resistance) so 12 volts/ 600 ... connect yourself to a car battery you will only get 12v/1,000,000 ohms = 12 microamps. Nothing.

Is there a webpage that defines current volt amp charge ohm and similar words in one page?

Description : Is there a webpage that defines current volt amp charge ohm and similar words in one page?

Last Answer : http://www.powermate.com/generators/glossary.php and http://www.engelectric.com/lit/lit6glossary.htm look promising

A 100 turns coil shown in figure carries a current of 2 amp in a magnetic field `B=0.2 Wb//m^(2)`. The torque acting on the coil is

Description : A 100 turns coil shown in figure carries a current of 2 amp in a magnetic field `B=0.2 Wb//m^(2)`. The torque acting on the coil is

Last Answer : A 100 turns coil shown in figure carries a current of 2 amp in a magnetic field `B=0.2 Wb//m^( ... N-m` tending to rotate the side AD into of the page

In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Description : In the schematic diagram of the DC compound generator shown in the illustration, the positive ammeter reading is 500 amps and the negative ammeter reading is 475 amps. What is the current flow through the neutral bus? EL-0037 A. 0 amp B. 12.5 amp C. 25 amp D. 975 amp

Last Answer : Answer: C

A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Description : A load is connected to the secondary of the transformer illustrated and the current through the load is 10 amps. If the step-up ratio is 10 to 1 and the input voltage is 110 VAC, what will be the current flow through the primary? EL-0055 A. 1 amp B. 10 amps C. 100 amps D. 1000 amps

Last Answer : Answer: C

When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A) and (+10 A) jacks B. 10 MA/ 10 AMP with leads in the (-COMMON) and (+) jacks C. 10 MA/ 10 AMP with leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Description : When reading AC current with the multimeter shown in the illustration and you are unsure of the range, the range switch should be set to ___________. EL-0047 A. 10 MA/ 10 AMP with leads in the (-10 A ... leads in the (-COMMON) and (+10 A) jacks D. unable to measure AC current with this multimeter

Last Answer : Answer: D

The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Description : The illustrated circuits are used to measure ___________. EL-0024 A. resistance B. gauss or magnetic field strength C. battery discharge rate in Amp-hours D. current

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 24 kohms, and R2 is 3610 ohms what is the current flowing through R1? EL-0036 A. .434 milliamps B. .005 amp C. 6.00 amps D. 2.4 milliamps

Last Answer : Answer: A