Beta in grounded emitter circuit is very high due to

Question

Beta in grounded emitter circuit is very high due to

asked Mar 29, 2018 by anonymous

1 Answer

Related questions

For which of the following reasons is plutonium-238 used for generating electricity on spacecraft? w) It is an alpha emitter with long half-life. x) It is a beta emitter with high specific power. y) It occurs abundantly in nature. z) It has low specific power.

Description : For which of the following reasons is plutonium-238 used for generating electricity on spacecraft? w) It is an alpha emitter with long half-life. x) It is a beta emitter with high specific power. y) It occurs abundantly in nature. z) It has low specific power.

Last Answer : ANSWER: W -- IT IS AN ALPHA EMITTER WITH LONG HALF-LIFE.

In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the

Description : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: (1) 10 µA (2) 100 µA (3) 1 A (4) 10 A

Last Answer : In the common–emitter transistor circuit, if the current gain is 100 and the collector current is 10 mA, the base current is: 100 µA

An emitter follower circuit is widely used in electronic instruments because

Description : An emitter follower circuit is widely used in electronic instruments because (A) Its voltage gain is less than unity (B) its output impedance is high and input impedance is low (C) its output impedance is low and input impedance is high (D) none of the above

Last Answer : Don't no happy be

The decay product of tritium (a beta emitter) is (A) Lithium (B) Helium (C) Deuterium (D) Hydrogen

Description : The decay product of tritium (a beta emitter) is (A) Lithium (B) Helium (C) Deuterium (D) Hydrogen

Last Answer : (B) Helium

Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Description : Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars? A. A grounded commutator bar B. Using improper carbon brushes C. Aligning the front and rear mica V-rings improperly D. An open circuit in the armature

Last Answer : Answer: B

If a transistor were operated with emitter and collector interchanged, then

Description : If a transistor were operated with emitter and collector interchanged, then 1 .emitter current will increase 2. Collector current will increase 3. Base current will decrease 4. No current flow will take place

Last Answer : If a transistor were operated with emitter and collector interchanged, then Collector current will increase

When a transistor is connected in common emitter mode, it with have

Last Answer : When a transistor is connected in common emitter mode, it with have medium input resistance and high output resistance.

You are performing an out-of-circuit test of the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' position and with leads properly installed, which of the listed results would you expect the Emitter-Collector connections of a go EL-0068 A. A low reading with red lead on 'B' and black lead on 'C'; and a low reading with the leads reversed. B. A high reading with red lead on 'B' and black lead on 'C'; and a high reading with the leads reversed. C. A low reading with red lead on 'A' and black lead on 'C'; and a high reading with the leads reversed. D. A high reading with red lead on 'B' and black lead on 'A'; and a low reading with the leads reversed.

Description : You are performing an out-of-circuit test of the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' position and with leads properly installed, which of the listed results would you expect the ... lead on 'B' and black lead on 'A'; and a low reading with the leads reversed.

Last Answer : Answer: B

You are performing an out-of-circuit test on the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' setting and with leads properly inserted, which of the listed results would indicate a good Emitter-Base junction? EL-0068 A. A low reading with red lead on 'A' and black lead on 'C'; and a high reading with the leads reversed. B. A low reading with red lead on 'A' and black lead on 'B'; and a high reading with the leads reversed. C. A low reading with black lead on'A' and red lead on 'B'; and a high reading with the leads reversed. D. A low reading with black lead on 'A' and red lead on 'C'; and a high reading with the leads reversed.

Description : You are performing an out-of-circuit test on the semi-conductor shown in the illustration. Using an ohmmeter on 'low power' setting and with leads properly inserted, which of the listed results would indicate a good ... lead on 'A' and red lead on 'C'; and a high reading with the leads reversed.

Last Answer : Answer: D

The final step in testing a circuit for a ground involves the use of a megohmmeter. A grounded switch or cable will be indicated by a megohmmeter reading of ____________. A. 'zero' B. infinity C. steady in the high range D. unsteady in the low range

Description : The final step in testing a circuit for a ground involves the use of a megohmmeter. A grounded switch or cable will be indicated by a megohmmeter reading of ____________. A. 'zero' B. infinity C. steady in the high range D. unsteady in the low range

Last Answer : Answer: A

One input terminal of high gain comparator circuit is grounded and a ...

Description : One input terminal of high gain comparator circuit is grounded and a sinusoidal voltage is applied to the other input. The output of comparator will be___________.

Last Answer : One input terminal of high gain comparator circuit is grounded and a sinusoidal voltage is applied to the other input. The output of comparator will be a square wave.

A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Description : A common-emitter circuit has an input voltage of 0.1 volt, an output voltage of 2.0 volts, an input current of 0.5 milliamps, and an output current of 10 milliamps. What is the power gain? A. 20 B. 40 C. 400 D. 4000

Last Answer : Answer: C

In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0022 A. common base B. reverse bias, negative feedback C. common emitter D. common collector

Last Answer : Answer: C

In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Description : In the illustration, the small battery and Rb are in the circuit to apply ________. EL-0022 A. forward bias to the emitter-base B. reverse bias to the emitter-base C. a 'reference charge' on the input capacitor D. a buffer between the input ground and the emitter ground

Last Answer : Answer: A

In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Description : In the illustrated circuit, the amplifier is connected in what basic configuration? EL-0045 A. common emitter B. common collector C. darlington paired, capacitor coupled D. common base

Last Answer : Answer: D

In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector

Description : In the illustration, the large battery and R(L) are in the circuit to ________. EL-0022 A. forward bias the emitter-base B. reverse bias the emitter-base C. forward bias the emitter/collector D. reverse bias the emitter/collector

Last Answer : Answer: D

What is the input current in the common-emitter circuit?

Description : What is the input current in the common-emitter circuit?

Last Answer : Base current (IB).

What is the polarity of the first alternation of the tank circuit in an emitter-loaded npn pulsed oscillator?

Description : What is the polarity of the first alternation of the tank circuit in an emitter-loaded npn pulsed oscillator?

Last Answer : Negative

The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage

Description : The common-emitter transistor circuit can amplify a small current signal because a small change in the signal current produces one of the following. Does the change in signal produce a large change in the: w) emitter-base voltage x) base current y) collector current z) collector voltage

Last Answer : ANSWER: Y -- COLLECTOR CURRENT

What is an emitter follower BJT circuit ?

Description : What is an emitter follower BJT circuit ? (A) Common Collector Amplifier (B) Common Emitter Amplifier (C) Common Base Amplifier (D) None of the above

Last Answer : What is an emitter follower BJT circuit ? (A) Common Collector Amplifier (B) Common Emitter Amplifier (C) Common Base Amplifier (D) None of the above

Explain open emitter BJT drive circuit.

Description : Explain open emitter BJT drive circuit.

Last Answer : open emitter BJT drive circuit:

Beta cut-off frequency of a transistor is the frequency at which the Beta is

Description : Beta cut-off frequency of a transistor is the frequency at which the Beta is • 0.707 of low frequency value • Zero • Equal to low frequency value • None of the above.

Last Answer : Beta cut-off frequency of a transistor is the frequency at which the Beta is 0.707 of low frequency value

bjt what is beta ?

Last Answer : Beta is the current gain which is the ratio of collector current to base current.

A circuit that has one of two wires in contact with the hull of a ship, is called a _____________. A. grounded circuit B. short circuit C. series circuit D. closed circuit

Description : A circuit that has one of two wires in contact with the hull of a ship, is called a _____________. A. grounded circuit B. short circuit C. series circuit D. closed circuit

Last Answer : Answer: A

A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Description : A circuit with a blown fuse would be described as a/an _____________. A. short circuit B. open circuit C. bonded circuit D. grounded circuit

Last Answer : Answer: B

The ground indicating light on the main electrical switchboard is indicating a ground. The best procedure for locating the grounded circuit is to _____________. A. trace the circuit paths while looking for burned spots B. check circuit resistances with a megohmmeter connected between the grounded line and the distribution panel framework C. open the circuit breakers on the distribution panel, one at a time, until the lights no longer indicate a ground D. check all circuits for continuity

Description : The ground indicating light on the main electrical switchboard is indicating a ground. The best procedure for locating the grounded circuit is to _____________. A. trace the circuit paths while looking for ... a time, until the lights no longer indicate a ground D. check all circuits for continuity

Last Answer : Answer: C

The circuit illustrated represents a 2 wire DC ground detecting system. If the positive bus is grounded and the test button is pushed, which of the lamps will be brightest? EL-0008 A. X B. Y C. both will be equal brightness. D. both will go out.

Description : The circuit illustrated represents a 2 wire DC ground detecting system. If the positive bus is grounded and the test button is pushed, which of the lamps will be brightest? EL-0008 A. X B. Y C. both will be equal brightness. D. both will go out.

Last Answer : Answer: C

What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to point 'Z'. C. It depends on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Description : What is the direction of current through the load resistor in the circuit shown in the illustration? EL-0085 A. Always from point 'Z' to the grounded end. B. Always from the grounded end to ... on the instantaneous polarity at point 'W'. D. It cannot be determined without a directional ammeter.

Last Answer : Answer: B

While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to check its value? A. Correct polarity must be observed because reverse bias will damage the component. B. Meter leads must not be twisted so as to cancel out the individual magnetic fields. C. Resistor's circuit must be de-energized and at least one end of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Description : While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to ... of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Last Answer : Answer: C

For more complete vessel protection when using an impressed current cathodic system _____________. A. all ship's service alternators have additional temperature sensing devices and a thermal recorder installed B. machinery on deck and in the engineroom is first coated with zinc chromate before final painting C. the hull's magnetic fields are aligned with a solid-state degaussing circuit using SCR's D. straps connect the rudder with the hull and the propeller shaft is grounded through a slip ring/brush arrangement

Description : For more complete vessel protection when using an impressed current cathodic system _____________. A. all ship's service alternators have additional temperature sensing devices and a thermal recorder ... with the hull and the propeller shaft is grounded through a slip ring/brush arrangement

Last Answer : Answer: D

Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common talking circuit is composed of two ungrounded wires. C. The ringing circuit has two grounded wires connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Description : Which of the following statements is correct concerning the circuits in a sound powered telephone system? A. The ringing circuit is composed of only one common wire to ground. B. The common ... connected to each station. D. The talking and calling circuits are electrically dependent upon each other.

Last Answer : Answer: B

I was born a long time ago and have since grown to be respected amongst my peers. I have 2 younger siblings who also make my family proud. My father, a greatly respected figure, taught us many values to keep us focused and aligned. It was very important for my mother also, to instill in us a sense of Purpose and to teach us to be Humble in life despite our successes. 'For as long as you've been around, the number of things you stand for, and the trinity that symbolizes you' those are the things that matter, my father always said. Understanding who I am is the key, my story isn’t fiction, it is grounded in reality, under most of your feet. Who am I? -Riddles

Description : I was born a long time ago and have since grown to be respected amongst my peers. I have 2 younger siblings who also make my family proud. My father, a greatly respected figure, taught us many values to ... story isn't fiction, it is grounded in reality, under most of your feet. Who am I? -Riddles

Last Answer : This answer was deleted by moderators

March 2019, the Directorate General of Civil Aviation of India grounded which aircraft due to technical fault?

Description : March 2019, the Directorate General of Civil Aviation of India grounded which aircraft due to technical fault?

Last Answer : Boeing 737 Max 8

Rapid hardening cement attains early strength due to (A) Larger proportion of lime grounded finer than normal cement (B) Lesser proportion of lime grounded coarser than normal cement (C) Lesser proportion of lime grounded finer than normal cement (D) Excess percentage of gypsum

Description : Rapid hardening cement attains early strength due to (A) Larger proportion of lime grounded finer than normal cement (B) Lesser proportion of lime grounded coarser than normal cement (C) Lesser proportion of lime grounded finer than normal cement (D) Excess percentage of gypsum

Last Answer : Answer: Option A

Which light emitter is preferred for high-speed data in a fiber-optic system? ∙ A. incandescent ∙ B. LED ∙ C. neon ∙ D. laser

Description : Which light emitter is preferred for high-speed data in a fiber-optic system? ∙ A. incandescent ∙ B. LED ∙ C. neon ∙ D. laser

Last Answer : D. laser

Which light emitter is preferred for high speed data in a fiber-optic system ∙ a. Incandescent ∙ b. LED ∙ c. Neon ∙ d. Laser

Description : Which light emitter is preferred for high speed data in a fiber-optic system ∙ a. Incandescent ∙ b. LED ∙ c. Neon ∙ d. Laser

Last Answer : ∙ d. Laser

The crystal oscillator frequency is very stable due to

Last Answer : The crystal oscillator frequency is very stable due to High Q of the crystal.

When using a megohmmeter to determine which shunt field coil is grounded in a DC machine, you must ____________. A. insulate the field frame from the ship's hull B. disconnect each shunt field coil before testing C. use a motor driven high capacity megohmmeter D. remove all main line lead connections before testing

Description : When using a megohmmeter to determine which shunt field coil is grounded in a DC machine, you must ____________. A. insulate the field frame from the ship's hull B. disconnect each shunt ... C. use a motor driven high capacity megohmmeter D. remove all main line lead connections before testing

Last Answer : Answer: B

Violent gassing from a lead-acid battery while it is being charged, indicates that the _____________. A. plate separators are grounded B. battery compartment ventilation is inadequate C. electrolyte specific gravity is too low D. charging rate is too high

Description : Violent gassing from a lead-acid battery while it is being charged, indicates that the _____________. A. plate separators are grounded B. battery compartment ventilation is inadequate C. electrolyte specific gravity is too low D. charging rate is too high

Last Answer : Answer: D

A grounded switch or cable will be indicated by a megohmmeter reading of _____________. A. infinity B. 'zero' C. being unsteady in the high range D. being unsteady in the low range

Description : A grounded switch or cable will be indicated by a megohmmeter reading of _____________. A. infinity B. 'zero' C. being unsteady in the high range D. being unsteady in the low range

Last Answer : Answer: B

The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Description : The outer conductor of a coaxial transmission line is always grounded at the A. Input only B. Input and output C. Output only D. Point of high SWR

Last Answer : B. Input and output

Which sector is the largest emitter of greenhouse gases in India ? -Do You Know?

Description : Which sector is the largest emitter of greenhouse gases in India ? -Do You Know?

Last Answer : answer:

What is an emitter ?

Description : What is an emitter ?

Last Answer : One side of a transistor that provides a charge carrier (hale or electron) is called an emitter. The solitary is always subjected to a land-oriented inclination. As a result, the discharge provides a greater number of charge carriers.

What is Emitter Shunt Register ?

Description : What is Emitter Shunt Register ?

Last Answer : To increase the range of the ammeter, a low value resistor is connected in parallel with the coil , called the ammeter shunt resistor.

What is an emitter ?

Description : What is an emitter ?

Last Answer : Ammeter , an instrument that can be used to directly measure the flow of electricity in a single electric ampere. This is a galvanometer whose resistance is very low. It has to be connected in series with the circuit. As a result, the entire current flows through the meter coil.

Is the base region much thinner or much wider than the collector and the emitter regions?

Description : Is the base region much thinner or much wider than the collector and the emitter regions?

Last Answer : yes its thinnerMost of the free electrons that have entered the base do notrecombine with holes because the base is very thin.

The diagram shown in the illustartion represents a/an _____________. EL-0022 A. magnectic amplifier B. common base amplifier C. common collector amplifier D. common emitter amplifier

Description : The diagram shown in the illustartion represents a/an _____________. EL-0022 A. magnectic amplifier B. common base amplifier C. common collector amplifier D. common emitter amplifier

Last Answer : Answer: D

As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector

Description : As shown in the illustration, which of the elements listed does the line 'B' represent in the basic schematic symbol of a PNP transistor? EL-0068 A. Base B. Emitter C. Cathode D. Collector

Last Answer : Answer: D

Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. C. Shift the 'Q' point to increase collector current. D. Increase the potential difference between the emitter and the base.

Description : Which of the following actions can be carried out in order to prevent thermal runaway in a transistor? A. Increase the current through the collector-base junction. B. Install a heat sink. ... point to increase collector current. D. Increase the potential difference between the emitter and the base.

Last Answer : Answer: B

The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward biased and the cathode-gate is forward biased C. source-gate is forward biased and the gate-drain is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased

Description : The device in figure 'B' shown in the illustration will conduct when the ____________. EL-0067 A. base-emitter is forward biased and the collector-base is reverse biased B. anode-cathode is forward ... is reversed biased D. terminal 1-2 is forward biased and the emitter-terminal 1 is reverse biased

Last Answer : Answer: B

anonymous · Answer 1 · 2018-03-29T07:24:48+0000

Beta in grounded emitter circuit is very high due to base current in small compared to collector current.

Beta in grounded emitter circuit is very high due to

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions