The slot leakage can be calculated by making which of the following assumptions ? (a) The current in the slot conductors is uniformly distributed over their cross-section (b) The leakage path is straight across the slot and around the iron at the bottom (c) The permanence of air paths is only considered. The reluctance of iron paths is assumed as zero (d) All of the above

The slot leakage can be calculated by making which of the following assumptions ?
(a) The current in the slot conductors is uniformly distributed over their cross-section
(b) The leakage path is straight across the slot and around the iron at the bottom
(c) The permanence of air paths is only considered. The reluctance of iron paths is
assumed as zero
(d) All of the above
by

1 Answer

Answer :

(d) All of the above
by

Related questions

Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Description : Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above

Last Answer : (e) All of the above

The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types

Description : The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types

Last Answer : (d) All of the above types

Materials exhibiting zero value of resistivity are known as ______ . (a) conductors (b) semiconductors (c) insulators (d) superconductors

Description : Materials exhibiting zero value of resistivity are known as ______ . (a) conductors (b) semiconductors (c) insulators (d) superconductors

Last Answer : (d) superconductors

In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Description : In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm

Last Answer : (d) between 25 to 35 mm

The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A

Description : The cylindrical windings using circular conductors are used for current rating of (a) upto 20 A (b) upto 40 A (c) upto 60 A (d) upto 80 A

Last Answer : (d) upto 80 A

The value of exciting or magnetizing current depends upon which of the following factors ? (a) Total m.m.f. required (b) The number of turns in the exciting winding (c) The way in which the winding is distributed (d) All of the above

Description : The value of exciting or magnetizing current depends upon which of the following factors ? (a) Total m.m.f. required (b) The number of turns in the exciting winding (c) The way in which the winding is distributed (d) All of the above

Last Answer : (d) All of the above

Yokes with rectangular cross-section are used for (a) small capacity transformers (b) medium capacity transformers (c) large capacity transformers (d) any of the above

Description : Yokes with rectangular cross-section are used for (a) small capacity transformers (b) medium capacity transformers (c) large capacity transformers (d) any of the above

Last Answer : (a) small capacity transformers

In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above

Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above

Last Answer : (c) 15 percent

Cylindrical windings using circular conductors, employed in transformers, are (a) single layered (b) double layered (c) multi-layered (d) none of the above

Description : Cylindrical windings using circular conductors, employed in transformers, are (a) single layered (b) double layered (c) multi-layered (d) none of the above

Last Answer : (c) multi-layered

In direct cooled system using hydrogen both stator and rotor conductors are made (a) solid (b) hollow (c) perforated (d) any ofthe above

Description : In direct cooled system using hydrogen both stator and rotor conductors are made (a) solid (b) hollow (c) perforated (d) any ofthe above

Last Answer : (b) hollow

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply supported beam fixed at hub and rim and carrying uniformly distributed load 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load

Description : For finding out the bending moment for the arm (spoke) of flywheel the arm is assumed as 1. a cantilever beam fixed at the rim and subjected to tangential force at the hub 2. a simply ... tangential force at the rim 4. a fixed beam fixed at hub and rim and carrying uniformly distributed load

Last Answer : 3. a cantilever hub fixed at the rim and subjected to tangential force at the rim

For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply supported beam fixed at hub and rim and carrying uniformly distributed load (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load

Description : For finding out the bending moment for the arm (spoke) of flywheel, the arm is assumed as, (A) A cantilever beam fixed at the rim and subjected to tangential force at the hub (B) A simply ... tangential force at the rim (D) A fixed beam fixed at hub and rim and carrying uniformly distributed load

Last Answer : (C) A cantilever beam fixed at the hub and subjected to tangential force at the rim

When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Description : When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Last Answer : Answer: B

The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Description : The most economical channel section for the fluid flow is the one for which the discharge is maximum for a given cross-sectional area. Vertical velocity distribution in an open channel for laminar flow can be assumed to be (A) Parabolic (B) Hyperbolic (C) Straight line (D) None of these

Last Answer : (A) Parabolic

For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2

Description : For large power transformers, self oil cooled type or air blast type which of the following values of current density may be used ? (a) 1.0 to 1.2 A/mm2 (b) 1.5 to 2.0 A/mm2 (c) 2.2 to 3.2 A/mm2 (d) 3.2 to 4.2 A/mm2

Last Answer : (c) 2.2 to 3.2 A/mm2

43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Description : 43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Last Answer : C. Decrease the reluctance of the magnetic path

Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Description : Hot rolled sheets have ______ value of permeability (a) zero (b) low (c) high (d) none ofthe above

Last Answer : (b) low

A copper rod which is 1 centimeter in diameter carries a current of 5 amps. The current is distributed uniformly throughout the rod. The magnetic field half way between the axis of the rod and its outside edge is: w) zero. x) pointing radially outward y) pointing radially inward z) circles the axis of the rod

Description : A copper rod which is 1 centimeter in diameter carries a current of 5 amps. The current is distributed uniformly throughout the rod. The magnetic field half way between the axis of the rod and its ... ) zero. x) pointing radially outward y) pointing radially inward z) circles the axis of the rod

Last Answer : ANSWER: Z -- CIRCLES THE AXIS OF THE ROD

In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above

Description : In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above

Last Answer : (b) high power factor

A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Description : A beam of uniform rectangular section 200 mm wide and 300mm deep is simply supported at its ends.It carries a uniformly distributed load of 9KN/m run over the entire span of 5m.If E=1×104 N/mm2, what is the maximum deflection? a.14.26 mm b.17.28 mm c.18.53 mm d.16.27 mm.

Last Answer : d.16.27 mm.

A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Description : A simply supported beam is of rectangular section.It carries a uniformly distributed load over the whole span.The deflection at the centre is y.If the depth of beam is doubled ,the deflection at the centre would be a.2y b.4y c.y/2 d.y/8.

Last Answer : d.y/8.

is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron

Description : is usually used for brush rockers (a) Mild steel (b) Copper (c) Aluminium (d) Cast-iron

Last Answer : (d) Cast-iron

______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel

Description : ______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel

Last Answer : (b) Cast steel

________ has a lowrelative permeability and is used principally in field frames when cost is of primary importance and extra weight is not objectionable. (a) Cast steel (b) Aluminium (c) Soft steel (d) Cast iron

Description : ________ has a lowrelative permeability and is used principally in field frames when cost is of primary importance and extra weight is not objectionable. (a) Cast steel (b) Aluminium (c) Soft steel (d) Cast iron

Last Answer : (d) Cast iron

Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Description : Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron

Last Answer : (d) Cast-iron

If a three hinged parabolic arch, (span l, rise h) is carrying a uniformly distributed load w/unit length over the entire span, (A) Horizontal thrust is wl2 /8h (B) S.F. will be zero throughout (C) B.M. will be zero throughout (D) All the above

Description : If a three hinged parabolic arch, (span l, rise h) is carrying a uniformly distributed load w/unit  length over the entire span,  (A) Horizontal thrust is wl2 /8h (B) S.F. will be zero throughout  (C) B.M. will be zero throughout  (D) All the above 

Last Answer : (D) All the above 

A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at (A) Midpoint of the cantilever (B) Fixed point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Description : A cantilever carrying a uniformly distributed load W over its full length is propped at its free end such that it is at the level of the fixed end. The bending moment will be zero at its free end also at ... point of the cantilever (C) 1/4th length from free end (D) 3/4th length from free end

Last Answer : (D) 3/4th length from free end

In a simply supported beam (l + 2a) with equal overhangs (a) and carrying a uniformly distributed load over its entire length, B.M. at the middle point of the beam will be zero if (A) l = 2a (B) l = 4a (C) l < 2a (D) l > a

Description : In a simply supported beam (l + 2a) with equal overhangs (a) and carrying a uniformly distributed load over its entire length, B.M. at the middle point of the beam will be zero if (A) l = 2a (B) l = 4a (C) l < 2a (D) l > a

Last Answer : (A) l = 2a

A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its free end upward. The net deflection of the free end will be (A) Zero (B) (5/24) (WL3 /EI) upward (C) (5/24) (WL3 /EI) downward (D) None of these

Description : A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its  free end upward. The net deflection of the free end will be  (A) Zero  (B) (5/24) (WL3 /EI) upward  (C) (5/24) (WL3 /EI) downward  (D) None of these 

Last Answer : (B) (5/24) (WL3 /EI) upward

The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Description : The shear force at the centre of a simply supported beam of span l carrying a uniformly distributed load of w per unit length over the whole span is (a) wl (b) wl/2 (c) wl/4 (d) Zero

Last Answer : (d) Zero

A cable with a uniformly distributed load per horizontal metre run will take the following shape (A) Straight line (B) Parabola (C) Hyperbola (D) Elliptical

Description : A cable with a uniformly distributed load per horizontal metre run will take the following shape (A) Straight line (B) Parabola (C) Hyperbola (D) Elliptical

Last Answer : (B) Parabola

If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be. (A) Straight below centroidal axis (B) Parabolic with convexity downward (C) Parabolic with convexity upward (D) Straight above centroidal axis

Description : If the loading on a pre-stressed rectangular beam, is uniformly distributed, the tendon to be provided should be. (A) Straight below centroidal axis (B) Parabolic with convexity downward (C) Parabolic with convexity upward (D) Straight above centroidal axis

Last Answer : Answer: Option B

For any part of a beam subjected to uniformly distributed load, bending moment diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : For any part of a beam subjected to uniformly distributed load, bending moment diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : d) Parabola

For any part of a beam subjected to uniformly distributed load, Shear force diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Description : For any part of a beam subjected to uniformly distributed load, Shear force diagram is (a) Horizontal straight line (b) Vertical straight line (c) Line inclined to x-axis (d) Parabola

Last Answer : (c) Line inclined to x-axis

A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Description : A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Last Answer : (3) Near the neck Explanation: When the bottle of soda water is grasped by the neck and swung briskly in a vertical circle, the bubbles collect at the top of the bottle which is ... beverage forms form bubbles when the dissolved carbon dioxide is depressurized to form emulsions at the top.

A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Description : A bottle of sodalime is grasped by the neck and swung briskly in a vertical circle, Near which portion of the bottle do the bubbles collect? (1) Near the bottom (2) In the middle of the bottom (3) Near the neck (4) Bubbles remain distributed uniformly

Last Answer : Near the neck

In a simply supported beam, bending moment at the end (a) Is always zero if it does not carry couple at the end (b) Is zero, if the beam has uniformly distributed load only (c) Is zero if the beam has concentrated loads only (d) May or may not be zero

Description : In a simply supported beam, bending moment at the end (a) Is always zero if it does not carry couple at the end (b) Is zero, if the beam has uniformly distributed load only (c) Is zero if the beam has concentrated loads only (d) May or may not be zero

Last Answer : (a) Is always zero if it does not carry couple at the end

27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Description : 27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Last Answer : B. Leakage path do not saturate

In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Description : In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A

Last Answer : (d) 400 A

Which of the following brushes can be used for high values of current density ? (a) Metal graphite brushes (b) Hard carbon brushes (c) Electro-graphitic brushes (d) Natural graphite brushes

Description : Which of the following brushes can be used for high values of current density ? (a) Metal graphite brushes (b) Hard carbon brushes (c) Electro-graphitic brushes (d) Natural graphite brushes

Last Answer : (a) Metal graphite brushes

A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Description : A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2

Last Answer : (d) 5.4 to 6.2 A/mm2

Which of the following methods is most accurate ? (a) Equivalent current method (b) Equivalent power method (c) Equivalent torque method (d) Method of average losses

Description : Which of the following methods is most accurate ? (a) Equivalent current method (b) Equivalent power method (c) Equivalent torque method (d) Method of average losses

Last Answer : (a) Equivalent current method

Which of the following methods does not take into account the maximum temperature rise under variable load conditions ? (a) Equivalent power method (b) Equivalent current method (c) Method of average losses (d) Equivalent torque method

Description : Which of the following methods does not take into account the maximum temperature rise under variable load conditions ? (a) Equivalent power method (b) Equivalent current method (c) Method of average losses (d) Equivalent torque method

Last Answer : (c) Method of average losses

By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Description : By which of the following methods motor rating for variable load drives can be determined ? (a) Method of average losses (b) Equivalent current method (c) Equivalent torque method (d) Equivalent power method (e) All of the above.

Last Answer : (e) All of the above.

The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Description : The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above

Last Answer : (a) quiet

D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Description : D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above

Last Answer : (c) better ventilation

The forced oil and air circulation method is usual one for transformers of capacities (a) upto 5 MVA (b) upto 10 MVA (c) upto 20 MVA (d) 30 MVA upwards

Description : The forced oil and air circulation method is usual one for transformers of capacities (a) upto 5 MVA (b) upto 10 MVA (c) upto 20 MVA (d) 30 MVA upwards

Last Answer : (d) 30 MVA upwards

The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above

Description : The noise produced by a ______ cooled machine is less as the rotor moves in a medium of smaller density. (a) air (b) hydrogen (c) either (a) or (b) (d) none of the above

Last Answer : (b) hydrogen

The thermal conductivity of hydrogen is ______ times that of air (a) 2 (b) 3 (c) 5 (d) 7

Description : The thermal conductivity of hydrogen is ______ times that of air (a) 2 (b) 3 (c) 5 (d) 7

Last Answer : (d) 7