Description : Which ofthe following materials is used in the manufacture of resistance grids to be used in the starters of large motors ? (a) Copper (b) Aluminium (c) Steel (d) Cast-iron
Last Answer : (d) Cast-iron
Description : ________ has a lowrelative permeability and is used principally in field frames when cost is of primary importance and extra weight is not objectionable. (a) Cast steel (b) Aluminium (c) Soft steel (d) Cast iron
Last Answer : (d) Cast iron
Description : is universally used for windings of electrical machines because it is easily workable without any possibility of fracture. (a) Silver (b) Steel (c) Aluminium (d) Copper
Last Answer : (d) Copper
Description : Which of the following materials may prove unsuitable for handling acetic acid (glacial & anhydrous) at 40°C? (A) Silicone rubber, teflon, porcelain and wood (B) Nickel, monel, stainless steel and graphite (C) Aluminium, copper, high silicon iron (D) Brass, cast iron, mild steel and tin
Last Answer : (D) Brass, cast iron, mild steel and tin
Description : H2SO4 (< 50% concentration) is corrosive to (A) Aluminium, mild steel, stainless steel, concrete & tin (B) Copper, cast iron & high silicon iron (14% Si) (C) Rubber (butyl and hard), silicone rubber & Teflon (D) Glass, graphite, porcelain & stoneware
Last Answer : (A) Aluminium, mild steel, stainless steel, concrete & tin
Description : Which of the following material of construction may be recommended by a chemical engineer for handling a gaseous chlorine (dry or wet) stream in a fluid flow system? (A) High silicon iron, silicon rubber ... Mild steel and stainless steel (C) Cast iron, tin and aluminium (D) Copper, nickel and Monel
Last Answer : (A) High silicon iron, silicon rubber, Kel-F and Teflon
Description : ______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel
Last Answer : (b) Cast steel
Description : Acetaldehyde is produced by hydration of acetylene in a sulphuric acid solution of mercuric sulphate. Hydration tower is made of (A) Rubber lined mild steel (B) Lead lined mild steel (C) Aluminium (D) Cast iron
Last Answer : (A) Rubber lined mild steel
Description : 100% H2SO4 at 30°C can't be stored in a vessel made/lined with (A) Cast iron and high silicon iron (B) Mild steel and stainless steel (C) Aluminium, tin and rubber (D) Teflon, glass and porcelain
Last Answer : (C) Aluminium, tin and rubber
Description : In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A
Last Answer : (d) 400 A
Description : In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above
Last Answer : (b) equal to
Description : The coefficient of static friction will have the highest value in case of a.Mild steel and mild steel b.Mild steel and copper c.Cast iron and steel d.Rope and wood e.Any of the above loctions
Last Answer : d. Rope and wood
Description : Out of the following, the __________ pipe has the least corrosion resistance. (A) Mild steel (B) Copper (C) Cast iron (D) Wrought iron
Last Answer : D) Wrought iron
Description : The shafts are made of a. mild steel b. alloy steel c. copper alloys d. cast iron.
Last Answer : d. cast iron.
Description : Plate and frame filter press is usually made of (A) Mild steel (B) Cast iron (C) Stainless steel (D) Galvanised iron
Last Answer : (B) Cast iron
Description : Mould board are usually made from a. Soft centre steel b. Hardened carbon steel c. Chilled cast iron d. Mild steel
Last Answer : a. Soft centre steel
Description : Aluminium when adopted as a conductor material in ______ transformers, decreases the overall cost of the transformer (a) small size (b) medium size (c) large size (d) any of the above size
Last Answer : (a) small size
Description : Mixing vessel used for the chlorination of methane to produce methyl chloride is made of (A) Copper (B) Cast iron (C) Aluminium (D) High carbon steel
Description : The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above
Last Answer : (a) increase
Description : In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30
Last Answer : (c) between 9 to 16
Description : In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm
Last Answer : (d) 10 mm
Description : The laminations of the armature of a D.C. machine are usually _____ thick. (a) 0.1 to 0.2 mm (b) 0.2 to 0.3 mm (c) 0.3 to 0.4 mm (d) 0.4 to 0.5 mm
Last Answer : (d) 0.4 to 0.5 mm
Description : The high voltage winding is usually which of the following type ? (a) Cylindrical winding with circular conductors (b) Cross-over winding with either circular or small rectangular conductors (c) Continuous disc type winding with rectangular conductors (d) All of the above types
Last Answer : (d) All of the above types
Description : For 275 kV transformers, using cold rolled grain oriented steel, which of the following values of flux density may be used? (a) 1.0 Wb/m2 (b) 1.1 Wb/m2 (c) 1.3 Wb/m2 (d) 1.6 Wb/m2 (e) None of the above
Last Answer : (d) 1.6 Wb/m2
Description : The usual values of maximum flux densities for distribution transformers using hot rolled silicon steel are (a) 0.5 to 0.8 Wb/m2 (b) 0.8 to 1.0 Wb/m2 (c) 1.1 to 1.35 Wb/m2 (d) 1.4 to 1.8 Wb/m2
Last Answer : (c) 1.1 to 1.35 Wb/m2
Description : The cold rolled grain oriented steel has ______ permeability in the direction of the grain orientation. (a) minimum (b) maximum (c) nil (d) none of the above
Last Answer : (b) maximum
Description : In transformers using hot rolled steel, the cross-section of the yoke is made about _____ greater than that of the core (a) 5 percent (b) 10 percent (c) 15 percent (d) 30 percent (e) none of the above
Last Answer : (c) 15 percent
Description : The slot leakage can be calculated by making which of the following assumptions ? (a) The current in the slot conductors is uniformly distributed over their cross-section (b) The leakage path is straight ... is only considered. The reluctance of iron paths is assumed as zero (d) All of the above
Last Answer : (d) All of the above
Description : Which of the following has the least carbon percentage? (A) Low carbon steel (B) Mild steel (C) Wrought iron (D) White cast iron
Last Answer : (C) Wrought iron
Description : Carbon percentage is the same in cast iron and (A) Wrought iron (B) Pig iron (C) Mild steel (D) High silicon (14%) iron
Last Answer : (B) Pig iron
Description : Which one is remelted and poured into moulds to get cast iron? (A) Wrought iron (B) Pig iron (C) Low carbon steel (D) Mild steel
Description : Tank furnace used for melting of glass is made of (A) Mild steel (B) Cast iron (C) Refractory blocks (D) Stainless steel
Last Answer : (C) Refractory blocks
Description : The digester of a Gobar gas plant is a (A) Mild steel drum (B) Stainless steel vessel (C) Masonry well (D) Cast iron vessel
Last Answer : (C) Masonry well
Description : The material of construction of pressure mills used for squeezing out the juice from sugar cane is (A) Stainless steel (B) Cast iron (C) Mild steel (D) Monel
Description : Which of the following has the highest compressive strength? (A) Wrought iron (B) Cast iron (C) Mild steel (D) High carbon steel
Last Answer : (D) High carbon steel
Description : Hydrochloric acid absorber in made of (A) Cast iron (B) Mild steel (C) Karbate (D) Stainless steel
Last Answer : (C) Karbate
Description : Rotary driers are generally made of (A) Cast iron (B) Mild steel (C) High silicon iron (14% Si) (D) Tin lined with refractory bricks
Last Answer : (B) Mild steel
Description : In SO3 absorber (Contact Process), packing material used is of (A) Cast iron (B) Chemical stoneware (C) Karbate (D) Mild steel
Last Answer : (B) Chemical stoneware
Description : A mould board of MB plough is made of? a Cast iron b Chilled cast iron c Mild steel d Soft centre steel
Last Answer : d Soft centre steel
Description : Lead is poured into the joint between two- __________ pipes. (A) Mild steel (B) Concrete (C) Cast iron (D) Asbestos cement
Last Answer : (C) Cast iron
Description : Oxyacetylene reducing flame is used while carrying out welding on (A) Alloy steel (B) Grey cast iron (C) Mild steel (D) High carbon steel
Last Answer : (C) Mild steel
Description : On being hit with a hammer, __________ will readily fracture. (A) Brass (B) Mild steel (C) Cast iron (D) Lead
Last Answer : C) Cast iron
Last Answer : Option C
Description : Lead is poured into the joint between two __________ pipes. (A) Mild steel (B) Concrete (C) Cast iron (D) Asbestos cement
Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)
Last Answer : Answer: Option D
Description : Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel
Last Answer : Answer: Option B
Description : The shovel of seed drill is made up of: A. Cast iron B. Mild steel C. White metal D. Carbon steel
Last Answer : Carbon steel
Description : - Material used for hand slide is (a) chilled cast iron. (b) cast iron (c) mild steel. (d) gun metal
Last Answer : (c) mild steel
Description : Share for use in sandy soils are made of A)chilled cast iron. B)cast iron C)mild steel. D)gun metal
Last Answer : Share for use in sandy soils are made of A)chilled cast iron. B)cast iron C)mild steel. D)gun metal
Description : Concentrated HCl at 30°C can be stored in a vessel made of (A) PTFE and porcelain (B) Cast iron and aluminium (C) Stainless steel and high silicon cast iron (D) None of these
Last Answer : (A) PTFE and porcelain