Description : With conventional hydrogen cooling it is possible to increase the rating of a single unit to (a) 50 MW (b) 100 MW (c) 200 MW (d) none ofthe above
Last Answer : (c) 200 MW
Description : Commercial available medium size machines have a speed range of ______ . (a) 200 to 400 r.p.m. (b) 600 to 1000 r.p.m. (c) 1000 to 1500 r.p.m. (d) 2000 to 2500 r.p.m.
Last Answer : (d) 2000 to 2500 r.p.m.
Description : Multiple inlet system of air cooling of turbo-alternators can be used for machines of rating upto (a) 10 MW (b) 30 MW (c) 60 MW (d) 150 MW
Last Answer : (c) 60 MW
Description : In a D.C. machine the current per brush arm should not be more than (a) 100 A (6) 200 A (e) 300 A (d) 400 A
Last Answer : (d) 400 A
Description : Which ofthe following is an advantage of hydrogen cooling ? (a) Increase in efficiency (b) Increase in ratings (c) Increase in life (d) Smaller size of coolers (e) All ofthe above
Last Answer : (e) All ofthe above
Description : Direct water cooling of rotor winding presents (a) no mechanical difficulties (b) lesser mechanical difficulties (c) greater mechanical difficulties (d) none of the above
Last Answer : (c) greater mechanical difficulties
Description : Machines cooled by direct cooling method may be called (a) "supercharged" (b) "inner cooled" (c) "conductor cooled" (d) any of the above
Last Answer : (d) any of the above
Description : cooling is the process of dissipating the armature and field winding losses to a cooling medium circulating within the winding insulation wall (a) Direct (b) Indirect (c) Conventional (d) Any ofthe above
Last Answer : (a) Direct
Description : The heat dissipating capability of transformers of ratings higher than 30 kVA in increased by providing which of the following ? (a) Corrugations (b) Fins (c) Tubes (d) Radiator tanks (e) All of the above
Last Answer : (e) All of the above
Description : A current density of _____ is ilsed for large power transformers with forced circulation of oil or with water cooling coils (a) 1.5 to 2.5 A/mm2 (b) 3.5 to 4.5 A/mm2 (c) 4.0 to 5.0 A/mm2 (d) 5.4 to 6.2 A/mm2
Last Answer : (d) 5.4 to 6.2 A/mm2
Description : Transformers with a capacity of upto _____ have a cooling radiator system with natural cooling (a) 2 MVA (b) 5 MVA (c) 7.5 MVA (d) 10 MVA
Last Answer : (d) 10 MVA
Description : In self cooled motors the cooling time constant is about ______ than the heating time constant because cooling conditions are worse at standstill. (a) 2 to 3 times greater (b) 3 to 4 times greater (c) 4 to 5 times greater (d) none of the above
Last Answer : (a) 2 to 3 times greater
Description : The time taken by the machine to attain 0.632 of its final steady temperature rise is called (a) heating time constant (b) cooling time constant (c) either (a) or (b) (d) none of the above
Last Answer : (a) heating time constant
Description : Which ofthe following methods is used for air cooling of turbo-alternators ? (a) One sided axial ventilation (b) Two sided axial ventilation (c) Multiple inlet system (d) All ofthe above
Last Answer : (d) All ofthe above
Description : For steam power plant having capacity 600 MW capacity a cooling tower is required to set up with condenser. Suggest the type of condenser and cooling tower with justification.
Last Answer : For Steam power plant having Capacity 600 MW the requirement of condenser and cooling tower is as follow. 1) Condenser:- Given Capacity is medium to low capacity for this we can use Jet Condenser ... and efficiency of tower is high -Temperature of water coming out from tower can be controlled.
Description : Minimum excretory urinary volume for waste products elimination during 24 hrs is (A) 200–300 ml (B) 200–400 ml (C) 500–600 ml (D) 800 ml
Last Answer : Answer : C
Description : In glycoproteins the carbohydrate is in the form of disaccharide units, the number of units are (A) 50–100 (B) 200–300 (C) 400–500 (D) 600–700
Last Answer : Answer : D
Description : Amylose contains glucose units (A) 100–200 (B) 200–300 (C) 300–400 (D) 500–600
Last Answer : C
Description : Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm
Last Answer : (b) 400-600 mm
Description : Number of meiotic divisions required to produce 200/400 seeds of pea would be (a) 200/400 (b) 400/800 (c) 300/600 (d) 250/500
Last Answer : (d) 250/500.
Description : A sewer has a diameter of 300 mm and slop of 1 in 400. While running full it has a mean velocity of 0.7 m/s. If both the diameter and slope are doubled (to respectively be 600 mm and 1 in 200), what will be the changed mean velocity ... 's formula. (a) 1.59 m/s (b) 2.80 m/s (c) 0.90 m/s (d) 1.00 m/s
Last Answer : (a) 1.59 m/s
Description : Power transformers have rating (a) equal to 50 kVA (6) equal to 100 kVA (c) above 200 kVA (d) none of the above
Last Answer : (c) above 200 kVA
Description : In direct cooled system using hydrogen both stator and rotor conductors are made (a) solid (b) hollow (c) perforated (d) any ofthe above
Last Answer : (b) hollow
Description : In induction motors, the length of air gap in kept as small as mechanically possible is order to have (a) low power factor (b) high power factor (c) high over load capacity (d) any of the above
Last Answer : (b) high power factor
Description : The efficiency of a machine should be as ______ as possible to reduce the operating cost. (a) high (b) low (c) either of the above (d) none of the above
Last Answer : (a) high
Description : The resistivity of water should not be less than (a) 10 Q m (b) 100 Q m (c) 1000 Q m (d) 2000 Q m
Last Answer : (d) 2000 Q m
Description : The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms
Last Answer : A. 500 to 600 ms
Description : In cranking the engine normally motor takes current about a) 300 amperes b) 400 amperesb) 5 0 0 amperes d) 600 amperes
Last Answer : b) 400 amperes
Description : How much cloves of garlic is required for one hectare (a) 400 kg (b) 500 kg (c) 600 kg (d) 300 kg
Last Answer : (a) 400 kg
Description : If the bit rate for an FSK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200
Last Answer : 1200
Description : f the bit rate for an ASK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200
Description : The cell mass can be measured optically by determining the amount of light scattered by a suspension of cells. The measurements are usually at a wavelength of A.300-400nm B.400-500nm C.500-600nm D.600-700nm
Last Answer : D.600-700nm
Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300
Last Answer : (C) 350-400
Description : Sum of tread and rise must lie between (A) 300 to 350 mm (B) 400 to 450 mm (C) 500 to 550 mm (D) 600 to 650 mm
Last Answer : Answer: Option B
Description : What class threaded flange is made without a counter-bore? a) 150. b) 300 and lower. c) 400 and lower. d) 600 and lower.
Last Answer : a) 150.
Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : a) 300-400rpm
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : What is Pre Heating Temperature of rail ends in AT Welding? (i) 300 ± 20oC (ii) 400 ± 20oC (iii) 500 ± 20oC (iv) 600 ± 20oC *
Last Answer : (iv) 600 ± 20oC *
Description : If a body (coated black) at `600 K` surrounded by atmosphere at `300 K` has cooling rate `r_(0)`, the same body at `900 K`, surrounded by the same atm
Last Answer : If a body (coated black) at `600 K` surrounded by atmosphere at `300 K` has cooling rate `r_(0)`, the same body ... (0)//16` C. `16r_(0)` D. `4r_(0)`
Description : In D.C. machines the number of slots per pole usually lies (a) between 2 to 4 (b) between 6 to 8 (c) between 9 to 16 (d) between 20 to 30
Last Answer : (c) between 9 to 16
Description : In D.C. machines the usual limit of slot pitch is (a) between 5 to 10 mm (b) between 10 to 15 mm (c) between 15 to 20 mm (d) between 25 to 35 mm
Last Answer : (d) between 25 to 35 mm
Description : Which of the following methods may be adopted to reduce the effects of armature reaction ? (a) Increase in length of air gap at pole tips (b) Increasing reluctance of pole tips (c) Compensating windings (d) Interpoles (e) All of the above
Description : The operation of a D.C. machine with large air gap lengths is comparatively (a) quiet (b) noisy (c) either of the above (d) none of the above
Last Answer : (a) quiet
Description : In D.C. machines, the ____ in field mmf results in increase in size and cost of machines. (a) increase (b) decrease (c) either of the above (d) none of the above
Last Answer : (a) increase
Description : In D.C. machines, ir order to prevent excessive distortion of field form by the armature reaction, the field mmf must be made (a) equal to that of armature mmf (b) less in comparison with the arma¬ture mmf (c) large in comparison with the arma-ture mmf (d) none of the above
Last Answer : (c) large in comparison with the arma-ture mmf
Description : D.C. machines designed with a large value of air gap length have (a) worst, ventilation (b) poor ventilation (c) better ventilation (d) none of the above
Last Answer : (c) better ventilation
Description : In D.C. machines the width of the duct is usually (a) 4 mm (b) 6 mm (c) 8 mm (d) 10 mm
Last Answer : (d) 10 mm
Description : In a D.C. machine, the value of peripheral speed should not, normally, exceed (a) 10 m/s (b) 20 m/s (c) 30 m/s (d) 40 m/s
Last Answer : (c) 30 m/s
Description : In a D.C. machine the number of brush arms is _____ the number of poles. (a) less than (b) equal to (c) greater than (d) none of the above
Last Answer : (b) equal to
Description : The weight of copper of both armature and field windings decreases with _____ in number of poles. (a) increase (b) decrease (c) either of the above (d) none of the above