Write the maximum power transfer theorem ?

1 Answer

Answer :

The maximum power transfer from a DC source to a resistive load will occur only when the internal resistance is equal to the series resistance connected to the load resistance source .

Related questions

Description : Write the Thebin Theorem ?

Last Answer : The current of a load resistance connected to two points of a complex network consisting of multiple sources of EMF and resistance will be the same if the load is connected to a single fixed source of EMF .

Description : What is Maxwell Theorem ?

Last Answer : The algebraic sum of the voltages in any mess or loop is zero.

Description : State Maximum power transfer theorem

Last Answer : The Maximum power transfer theorem explains about the load that a resistance will extract from the network. This includes the maximum power from the network and in this case the load resistance ... the output terminals and the energy sources can be removed by leaving the internal resistance behind.

Description : State maximum power transfer theorem. 

Last Answer : The maximum power transfer theorem states that the maximum amount of power will be delivered to the load resistance when the load resistance is equal to the Thevenin/ Norton resistance of the network supplying the power ... draws maximum power. Also find the value of the maximum power.

Description : Maximum Power Transfer Theorem 1

Last Answer : Maximum Power Transfer Theorem 1

Description : State maximum power transfer theorem for DC circuit.

Last Answer : Maximum power transfer theorem for DC circuit: The maximum power transfer theorem states that the source or a network transfers maximum power to load only when the load resistance is equal ... removed (disconnected) ii) All internal independent sources are replaced by their internal resistances.

Description : For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source impedance should be equal to: A) twice the load impedance B) complex conjugate of load impedance C) twice the complex conjugate of load impedance D) none of these 

Last Answer :  For AC networks, as per maximum power transfer theorem, for maximum power transfer, the source impedance should be equal to: complex conjugate of load impedance

Description : Write different font names or different short circuit font names ?

Last Answer : There are two main types of short circuit faults. Namely- 1. Semantic faults and 2. Asymmetrical font Symmetrical fault - a) Short circuit three phases together b) Short circuit asymmetrical fault with three ... result c) Double line to ground font d) Two phase one Circuit and third phase earth.

Description : Write the limitations of Kelvin's formula ?

Last Answer : As sometimes the cross section of the wire is so low that the regulation increases as the voltage drop increases . Increases , interest and waste change as space and time change.

Description : Write Kelvin's formula ?

Last Answer : In the case of energy transport , the cross-section of the lowest cost line conductor will occur only when the annual waste and interest cost is equal to the annual waste cost .

Description : Write the formula from Star to Delta ?

Last Answer : Answer : Dividing the product of the resistors connected to the star by dividing the resistors of the opposite arm by taking two together, the quotient is equal to the value of each resistor connected.

Description : Write the formula for inductive reaction ?

Last Answer : Formula for inductive reactance: XL = 2τƒL . It depends on the frequency and inductance of the coil. Since the inductance of a coil is constant, its inductive reactance changes at a rate proportional to the change in frequency.

Description : Write the types of modulation and demodulation ?

Last Answer : There are three main types of modulation. Namely: (a) Amplitude modulation: The modulation in which the amplitude of the carrier signal changes according to the modulating frequency is called ... the carrier signal changes according to the modulating frequency is called phase modulation.

Description : Write the use of diode ?

Last Answer : : Use of diode The use of diode is given below: (a) Acts as rectifier. (B) Acts as a dimulator or detector. (C) Acts as a switch. (D) Used in wave shaping circuits.

Description : Write the use of ginner diode ?

Last Answer : : Ginner diodes are used in the following places: (a) for DC voltage stabilizer and regulation. (B) To limit the amplitude of AC voltage. (C) Analog circuits. (D) Used in power circuits and ... diode is used in clippers circuit. (G) Ginner diodes are used in clipper clamper and protector circuits.

Description : Write the use of LED ?

Last Answer : The use of LEDs is highlighted below: (a) For digital display on decaed instruments. (B) In digital watch. (C) On the computer. (D) In all the techniques in which invisible light is used. ... in image sensing circuit. (G) LED is used in silica fiber optical cable in optical communication circuit .

Description : Write the properties of LED ?

Last Answer : LED features ( i) Fast on-off switching. ( ii) It is longevity. ( iii) Voltage consumption is low. ( iv) Gallium arsenide is used to obtain infrared algae.

Description : Write using photo diode ?

Last Answer : : Use of photo diode (a) to operate the relay circuit , ( b) to read the punch card of the computer fast , ( c) to automatically control the angle system , ( d) to determine the number ... , ( F) are used for controlling photoelectric resistors , ( g) are used for voltage and heat control systems.

Description : Write the properties of photo diode ?

Last Answer : : Features of photo diode ( i) It works based on Ala. ( ii) When the temperature is high, the resistance decreases , resulting in more current flowing. ( iii) When the light is low, the resistance increases , so the current flows less.

Description : Write the use of UPS ?

Last Answer : UPS is used to provide uninterrupted power supply to computer , medical equipment, and electrical devices, and to protect the device from voltage regulation , overvoltage , and undervoltage .

Description : Write speaker usage ?

Last Answer : The speaker is used in the following cases. Namely: (a) Used to convert amplified electrical energy into human audible sound energy. (B) For the production of sound waves in radio and ... sound in public address system , tape recorder , computer amplifier. (D) Used in telecommunication equipment.

Description : What is the best economic power factor ?

Last Answer : This means that raising the power factor results in maximum annual savings , in which case the value of the power factor is called the best saving power factor.

Description : What happens if the value of power factor is low ?

Last Answer : ( a) Current flows more , ( b) Copper loss increases , ( c) Heat increases , ( d) Output decreases , ( e) Voltage drop increases , ( f) Different electrical machinery heats up quickly. , ( G) The life span of various electrical machinery and appliances is reduced.

Description : What are the components of power transmission line ?

Last Answer : ( a) Power Plant , ( b) Conductor Wire , ( c) Transformer , ( d) Line Insulator , ( e) Line Support , ( f) Power Substation , ( g) Circuit Breaker , ( h) Relay , ( I) Isolator , ( j) Lighting Arrester

Description : What is the power unit of Transformer and why ?

Last Answer : The unit of power of the transformer is KVA . That is kilowatt volt ampere. The reason is that we know that the unit of power of any machine is determined based on its #loss . Exactly the same ... stood. This is why the unit of power of the transformer is written in kilowatt volt amperes or kVA .

Description : What is the Leading Power Factor ?

Last Answer : When the capacitive load of an AC circuit exceeds the inductive load , the pf of the circuit is called the leading pf . Thank you!

Description : What is Lagging Power Factor ?

Last Answer : When the inductive load of an AC circuit exceeds the capacitive load , the pf of the circuit is called lagging pf .

Description : What is Unity Power Factor ?

Last Answer : There is no angular gap between current and voltage in pure resistance. That is, the phase angle of current and voltage is φ = 0, the power factor of that circuit is one or unit. This is called Unity Power Factor.

Description : What is the leading power factor ?

Last Answer : When the amount of capacitive load is more than the inductive load in a circuit then the power factor of that circuit is called leading power factor.

Description : What is lagging power factor ?

Last Answer : When the amount of inductive load is greater than the capacitive load in a circuit then the power factor of that circuit is called lagging power factor.

Description : What is the power factor in pure resistive , capacitive , inductive load ?

Last Answer : Answer : Power factor cosΦ = 1 in pure resistive load, cosΦ = 0 in capacitive load , cosΦ = 0 in inductive load .

Description : What is Reactive Power ?

Last Answer : The product of the voltage of the AC circuit and the product of the reactive current or the vertical component of the current is called reactive power.

Description : How many types of power factor ?

Last Answer : Three types , namely , 1) lagging power factor , 2) leading power factor , 3) unity power

Description : What is the effect of resistance and reactance on power factor ?

Last Answer : Power factor depends on resistance and reactance. As the resistance of the circuit increases, the phase angle between the current and the voltage decreases, resulting in an increase in the power factor ... current and the voltage increases, resulting in a decrease in the power factor of the circuit.

Description : Active Power Depends on What Matters. ?

Last Answer : Active power : Depending on current , voltage and power factor.

Description : What is lagging power factor ?

Last Answer : The cosine value of the phase angle between current and voltage in an inductive circuit is called lagging power factor.

Description : How many types of power in AC circuit ?

Last Answer : Three types of power in AC circuit. Namely , 1) actual power , 2) reactive power , 3) apparent power.

Description : What is Power Factor ?

Last Answer : The phase factor or the cosine value of the angular interval between the voltage and current of an AC circuit is called the power factor.

Description : When is the power factor lagging , leading , unity ?

Last Answer : Power factor lagging in inductive load. Power factor leading in capacitive load is power factor unity in resistive load.

Description : What is Active Power ?

Last Answer : The product of voltage and active current of AC circuit is called active power or actual power.

Description : What is solar power and how does solar power work ?

Last Answer : The energy that is generated by using solar energy is called solar energy. You may have noticed that there is a panel on the floor of the house around you or on the top of the house. ... and medium range. Indirect use of sunlight is called concentrated solar power or concentrated solar power .

Description : What is Switch Made Power Supply ?

Last Answer : : SwitchMed Power Supply (SMPS) is a device that converts 230 volt power supply required for computer to regulated DC voltage. SMPS is commonly known as Power Supply Unit (PSU). It is a metal box ... to the capacity. PSUs with more capacity than what is required for a computer are always approved .

Description : What is the name of the main part of solar power ?

Last Answer : The main part of solar power is solar panel. Without it the whole part is void

Description : What is solar power ?

Last Answer : The energy that is obtained from the sun is called solar energy.

Description : What is a Power Factor Meter ?

Last Answer : The cosine angle between voltage and current is called power factor

Description : What is the expression of electric power ?

Last Answer : Electric power is expressed by P.

Description : What is the unit of electric power ?

Last Answer : Unit W of electric power

Description : What is the formula for determining the power in a circuit ?

Last Answer : The formula for circuit power is P = V * I watt here , P is power V is voltage I is current.

Description : What is electric power ?

Last Answer : The rate at which electric power is used is called electrical power.

Description : What is the relation of voltage with power ?

Last Answer : Power is proportional to P, voltage to V. For example: P = VI, P = V ^ 2 / R , that is, if the voltage increases, the power will increase.