A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is also in series with the diode. The current is a. 10 mA b. 9.3 mA c. 0.7 mA d. 0

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is also in series with the diode. The current is a. 10 mA b. 9.3 mA c. 0.7 mA d. 0
by

1 Answer

Answer :

b. 9.3 mA
by

Related questions

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the

Description : A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is

Last Answer : A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is 9.3 mA

Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Description : Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Last Answer : c. Reverse bias exceeds a certain value.

When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Description : When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Last Answer : a. Raise the potential barrier

The knee voltage (cut in voltage) of Si diode is a. 0.2 V b. 0.7 V c. 0.8 V d. 1.0 V

Description : The knee voltage (cut in voltage) of Si diode is a. 0.2 V b. 0.7 V c. 0.8 V d. 1.0 V

Last Answer : b. 0.7 V

When the diode is forward biased, it is equivalent to a. An off switch b. An On switch c. A high resistance d. None of the above

Description : When the diode is forward biased, it is equivalent to a. An off switch b. An On switch c. A high resistance d. None of the above

Last Answer : b. An On switch

The arrow direction in the diode symbol indicates a. Direction of electron flow. b. Direction of hole flow (Direction of conventional current) c. Opposite to the direction of hole flow d. None of the above

Description : The arrow direction in the diode symbol indicates a. Direction of electron flow. b. Direction of hole flow (Direction of conventional current) c. Opposite to the direction of hole flow d. None of the above

Last Answer : b. Direction of hole flow (Direction of conventional current)

In the diode equation, the voltage equivalent of temperature is a. 11600/T b. T/11600 c. T x 11600 d. 11600/T2

Description : In the diode equation, the voltage equivalent of temperature is a. 11600/T b. T/11600 c. T x 11600 d. 11600/T2

Last Answer : b. T/11600

Why 4-20 Ma Signal Is Preferred Over A 0-10v Signal?

Description : Why 4-20 Ma Signal Is Preferred Over A 0-10v Signal?

Last Answer : Generally in a transistor some amount of voltage is required for turning it on. This voltage is the cut in voltage. Up to this voltage the exists a nonlinearity in its characteristics. Beyond this cut in voltage ... region lays between 0-4ma, beyond 4ma it linear. This is why 4-20 ma range is used.

In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Description : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Last Answer : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L) ... (2) A` C. `20sqrt(2) A` D. `25sqrt(2) A`

Calculate the series resistance needed to convert a D' Arsonval meter with FSD of 100uA and a meter resistance of 1kohm to a voltmeter with 10V FSD.

Description : Calculate the series resistance needed to convert a D' Arsonval meter with FSD of 100uA and a meter resistance of 1kohm to a voltmeter with 10V FSD.

Last Answer : Rs=10V/100uA - 1kohm = 99kohm

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:

Description : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

Last Answer : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:  5.9 mA

A potential difference of V = 100 ± 2 volt, when applied across a resistance R gives a current of 10 ± 0.5 ampere.

Description : A potential difference of V = 100 ± 2 volt, when applied across a resistance R gives a current of 10 ± 0.5 ampere.

Last Answer : A potential difference of V = 100 2 volt, when applied across a resistance R gives a current of 10 ... percentage error in R given by R = V/I.

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Description : Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Last Answer : 7.5kΩ

In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Description : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Last Answer : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_ ... (a) and (b) are correct D. Both a and b are wrong

A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Last Answer : d) 0.03 Ω

Current in a circuit if resistance of 15 Ω and potential difference of 3.0 V is applied across it's ends is A. 1 A B. 2 A C. 0.5 A D. 0.20 A

Description : Current in a circuit if resistance of 15 Ω and potential difference of 3.0 V is applied across it's ends is A. 1 A B. 2 A C. 0.5 A D. 0.20 A

Last Answer : 0.20 A

In a semiconductor diode, p-side is earthed and to n-side is applied a potential of -2 volt; the diode shall (a) Conduct (b) Not conduct (c) Conduct partially (d) Break down

Description : In a semiconductor diode, p-side is earthed and to n-side is applied a potential of -2 volt; the diode shall (a) Conduct (b) Not conduct (c) Conduct partially (d) Break down

Last Answer : a) Conduct

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

When two 100 kΩ resistors are connected in parallel, net resistance is

Description : When two 100 kΩ resistors are connected in parallel, net resistance is

Last Answer : When two 100 kΩ resistors are connected in parallel, net resistance is 50 kΩ

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an

Description : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

Last Answer : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is 1.001 Ω

A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to...

Description : A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to be passed is 7.5 KHz. The value of suitable coupling capacitor must be : (A) 0.1 pF (B) 1 pF (C) 0.1 μ F (D) 1 μ F

Last Answer : Option C By equating 1/RC with frequency.

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

Why does a forward biased diode offer low resistance?

Description : Why does a forward biased diode offer low resistance?

Last Answer : The external voltage over comes the junction potential and provides an easy path for the flow of charges across the junction. Hence it offers low resistance.

What is the typical back-to-forward resistance ratio of a good-quality diode?

Description : What is the typical back-to-forward resistance ratio of a good-quality diode?

Last Answer : 10-to-1 ratio.

As a rule of thumb, what is an acceptable ratio of back-to forward resistance for a diode?

Description : As a rule of thumb, what is an acceptable ratio of back-to forward resistance for a diode?

Last Answer : Greater than 10 to 1

Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Description : Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Last Answer : Definition: The resistance offered by the diode to the AC operating conditions is known as the Dynamic resistance' or Incremental resistance' or AC resistance' of a diode. It is ... Dynamic resistance is actually the reciprocal of the slope of the forward characteristics.

Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of

Description : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms

Last Answer : Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor? A.4 ohms B.400 ohms C.4 kohms D.4.4 ohms

An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance

Description : An a.c series circuit has resistance of 10ohm, inductance of 0.1H and capacitance of 10µf, voltage applied to circuit is 200V. find (i) Resonant frequency (ii) Current at resonance (iii) Power at resonance 

Last Answer : Solution: For RLC series circuit

A galvanometer having a resistance of 4.5 Ω can read up to 5 mA. If it is to read 100 V, then the high resistance to be used in series will be a) 19998 Ω b) 19995.8 Ω c) 19995.5 Ω d) 19996.5 Ω

Description : A galvanometer having a resistance of 4.5 Ω can read up to 5 mA. If it is to read 100 V, then the high resistance to be used in series will be a) 19998 Ω b) 19995.8 Ω c) 19995.5 Ω d) 19996.5 Ω

Last Answer : c) 19995.5

Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Description : Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Last Answer : Answer :

When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 10.23 kohms the current will be _______ . EL-0018 A. 9.29 milliamps B. 107.68 amps C. 10.32 amps D. 11.02 amps

Description : When a voltage of 95 VDC is applied to the illustrated circuit with a resistance of 10.23 kohms the current will be _______ . EL-0018 A. 9.29 milliamps B. 107.68 amps C. 10.32 amps D. 11.02 amps

Last Answer : Answer: A

Forward current through a semi-conductor diode circuit is due to ________ (a) Minority carriers (b) majority carriers (c) holes (d) electrons

Description : Forward current through a semi-conductor diode circuit is due to ________ (a) Minority carriers (b) majority carriers (c) holes (d) electrons

Last Answer : (b) majority carriers

What is the maximum OCV allowable to initiate an arc when using A. C current? a) 1000V b) 10V c) 90V d) 900V

Description : What is the maximum OCV allowable to initiate an arc when using A. C current? a) 1000V b) 10V c) 90V d) 900V

Last Answer : c) 90V

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. act as a short circuit for the sensing coil when CEMF is applied B. insure that the voltage across the coil does not exceed 9 volts C. improve response time D. act as a filter to prevent hunting

Last Answer : Answer: A

A potential difference of 10 V is applied across a conductor of resistance `1 k Omega`. Find the number of electrons flowing through the conductor in

Description : A potential difference of 10 V is applied across a conductor of resistance `1 k Omega`. Find the number of electrons flowing through the conductor in

Last Answer : A potential difference of 10 V is applied across a conductor of resistance `1 k Omega`. ... of electrons flowing through the conductor in 5 minutes.

When the potential difference of 4 volt is applied across resistance, 10J energy is converted. Find the charge flows. a. 0.20 C b. 2.5C c. 5C d. 10C

Description : When the potential difference of 4 volt is applied across resistance, 10J energy is converted. Find the charge flows. a. 0.20 C b. 2.5C c. 5C d. 10C

Last Answer : b. 2.5C

A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. If it is to work as a voltmeter of `30 V` r

Description : A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. If it is to work as a voltmeter of `30 V` r

Last Answer : A galvanometer has a coil of resistance `100 Omega` and gives a full-scale deflection for `30 mA` current. ... Omega` C. `1000 Omega` D. `1800 Omega`

How much resistance is required to limit the current from a 12 V battery to 3.6 mA?

Description : How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

Last Answer : How much resistance is required to limit the current from a 12 V battery to 3.6 mA? A.3.3 k ohms B.33 k ohms C.2.2 k ohms D.22 k ohms

The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. ...

Description : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

Last Answer : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. 99.99 K ohms is the value of series resistor to be used.

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

Tunnel diode is a: a) Power diode b) Has light doping c) Has heavy doping d) Is a reverse recovery diode Ans: C 76.LEDs are fabricated from: a) Silicon b) Germanium c) Si or Ge d) Gallium arsenide

Description : Tunnel diode is a: a) Power diode b) Has light doping c) Has heavy doping d) Is a reverse recovery diode Ans: C 76.LEDs are fabricated from: a) Silicon b) Germanium c) Si or Ge d) Gallium arsenide

Last Answer : Ans: D

When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.242 amps B. 4.125 amps C. 7.757 amps D. 1.64 amps

Description : When a voltage of 132 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be ________. EL-0018 A. 0.242 amps B. 4.125 amps C. 7.757 amps D. 1.64 amps

Last Answer : Answer: B

In the network shown in fig. , points A, B, and C are at potentials of 70 V, 0, and 10V, respectively.

Description : In the network shown in fig. , points A, B, and C are at potentials of 70 V, 0, and 10V, respectively.

Last Answer : In the network shown in fig. , points A, B, and C are at potentials of 70 V, 0, and 10V, respectively. ... AB, DB and DC are in the ratio of `3:2:1`

I applied for PUA in MA, and received eligibility.However my payment keep saying pending and when I click on payment history, it shows this in every weeks payment "This week is not being paid while an issue is resolved." Anyone knows what this means?

Description : I applied for PUA in MA, and received eligibility.However my payment keep saying pending and when I click on payment history, it shows this in every weeks payment "This week is not being paid while an issue is resolved." Anyone knows what this means?

Last Answer : I was told this is standard practice. It has gone to the group that checks identity so "we know you are who you say you are." Assured that "you didn't do anything wrong." Apologized for ... earnings' for several weeks; then two payments with no explanation; then suspended pending now for a month.)

When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be________. EL-0018 A. .285 amps B. 3.5 amps C. 9.142 amps D. 144 m amps

Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 32 ohms the current will be________. EL-0018 A. .285 amps B. 3.5 amps C. 9.142 amps D. 144 m amps

Last Answer : Answer: B

When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be ________. EL-0018 A. .107 amps B. 1.28 amps C. 9.33 amps D. 124 milliamps

Description : When a voltage of 112 VDC is applied to the illustrated circuit with a resistance of 12 ohms the current will be ________. EL-0018 A. .107 amps B. 1.28 amps C. 9.33 amps D. 124 milliamps

Last Answer : Answer: C