A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is
by
by
Please show the working
by
Good

1 Answer

Answer :

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is 9.3 mA

by

Related questions

A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is also in series with the diode. The current is a. 10 mA b. 9.3 mA c. 0.7 mA d. 0

Description : A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is also in series with the diode. The current is a. 10 mA b. 9.3 mA c. 0.7 mA d. 0

Last Answer : b. 9.3 mA

When the diode is forward biased, it is equivalent to

Description : When the diode is forward biased, it is equivalent to

Last Answer : When the diode is forward biased, it is equivalent to An On switch

In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Description : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Last Answer : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L) ... (2) A` C. `20sqrt(2) A` D. `25sqrt(2) A`

Calculate the series resistance needed to convert a D' Arsonval meter with FSD of 100uA and a meter resistance of 1kohm to a voltmeter with 10V FSD.

Description : Calculate the series resistance needed to convert a D' Arsonval meter with FSD of 100uA and a meter resistance of 1kohm to a voltmeter with 10V FSD.

Last Answer : Rs=10V/100uA - 1kohm = 99kohm

What are the applications of diode ?

Description : What are the applications of diode ?

Last Answer : 1) Rectifier : - It is an electronics device used to convert AC to DC signal. The rectifier output is pulsating in nature their can be two types of rectifier. a) Half wave rectifier b) Full wave ... FWR are of two types : i) center tapped full wave rectifier ii) bridge type full wave rectifier

what is a diode

Description : if you got you will receive some cash

Last Answer : A diode is an electronic device which permits one directional flow of electric current.

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

A diode in which the change in reverse bias voltage varies the capacitance is called as

Description : A diode in which the change in reverse bias voltage varies the capacitance is called as A) Varactor diode B) Switching diode C) Tunnel diode D) Zener-diode  

Last Answer : A diode in which the change in reverse bias voltage varies the capacitance is called as Varactor diode

The region consisting of holes and electrons near the p-n junction of a diode is

Description : The region consisting of holes and electrons near the p-n junction of a diode is (A) diffusion region (B) neutral zone (C) recombination region (D) depletion region 

Last Answer : The  region  consisting  of  holes  and  electrons  in a  pn  junction  is called  depletion layer.The  reason  being  both  holes  and  electrons have neutrolyzed at the  junction  thus  it  is depleated  with  delocalized  charge  carriers.

The diode oftenly used for voltage regulation in electronic circuits is

Description : The diode oftenly used for voltage regulation in electronic circuits is (a) Zener (b) Varactor (c) Silicon (d) Germanium

Last Answer : The diode oftenly used for voltage regulation in electronic circuits is  Zener.

A power diode has lightly doped n type substrate sandwiched between heavily doped p and n regions

Description : A power diode has lightly doped n type substrate sandwiched between heavily doped p and n regions  (a) to increase reverse breakdown voltage (b) to reduce ohmic loss under forward bias (c) to decrease switching time of the power diode (d) to improve transient behaviour of the diode

Last Answer : A power diode has lightly doped n type substrate sandwiched between heavily doped p and n regions  to improve transient behaviour of the diode

The reverse breakdown phenomenon in a zener diode is known as

Description : The reverse breakdown phenomenon in a zener diode is known as

Last Answer : The reverse breakdown phenomenon in a zener diode is known as Avalanche effect

The arrow direction in the diode symbol indicates

Description : The arrow direction in the diode symbol indicates

Last Answer : Flow of current

The cut-in voltage of a silicon diode is approx.

Description : The cut-in voltage of a silicon diode is approx. • 0.7 volt • 0.3 volt • 1.4 volt • None of the above.

Last Answer : The cut-in voltage of a silicon diode is approx. 0.7 volt

The step Recovery Diode is used as

Description : The step Recovery Diode is used as • Frequency adder • Frequency subtractor • Frequency multiplier • None of the above.

Last Answer : The step Recovery Diode is used as Frequency multiplier

In a tunnel diode, electrons can tunnel through the P-N junction mainly because

Description : In a tunnel diode, electrons can tunnel through the P-N junction mainly because  1.impurity level is low 2.they have high energy 3.barrier potential is very low 4.depletion layer is extremely thin 

Last Answer : In a tunnel diode, electrons can tunnel through the P-N junction mainly because depletion layer is extremely thin 

Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Description : Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Last Answer : c. Reverse bias exceeds a certain value.

Barrier potential in a P-N junction is caused by

Description : Barrier potential in a P-N junction is caused by   (A) thermally generated electrons and holes (B) diffusion of majority carriers across the junction (C) migration of minority carriers across the junction (D) flow of drift current.

Last Answer : Barrier potential in a P-N junction is caused by migration of minority carriers across the junction

In a semiconductor diode, p-side is earthed and to n-side is applied a potential of -2 volt; the diode shall (a) Conduct (b) Not conduct (c) Conduct partially (d) Break down

Description : In a semiconductor diode, p-side is earthed and to n-side is applied a potential of -2 volt; the diode shall (a) Conduct (b) Not conduct (c) Conduct partially (d) Break down

Last Answer : a) Conduct

When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Description : When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Last Answer : a. Raise the potential barrier

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Description : Three resistors connected in parallel have values of 12 kΩ, 20kΩ, and 30kΩ. What is the equivalent resistance? A37. 6kΩ Q38. Two resistors connected in parallel have values of 10 kΩ and 30kΩ. What is eht equivalent resistance?

Last Answer : 7.5kΩ

When two 100 kΩ resistors are connected in parallel, net resistance is

Description : When two 100 kΩ resistors are connected in parallel, net resistance is

Last Answer : When two 100 kΩ resistors are connected in parallel, net resistance is 50 kΩ

A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an

Description : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is (A) 1 Ω (B) 1.001 Ω (C) 0.5 Ω (D) 10 Ω

Last Answer : A PMMC instrument has FSD of 100 μA and a coil resistance of 1 kΩ. To convert the instrument into an ammeter with full scale deflection of 100 mA, the required shunt resistance is 1.001 Ω

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:

Description : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

Last Answer : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:  5.9 mA

A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to...

Description : A high pass filter has a resistance R = 2 kΩ. The lowest input frequency to be passed is 7.5 KHz. The value of suitable coupling capacitor must be : (A) 0.1 pF (B) 1 pF (C) 0.1 μ F (D) 1 μ F

Last Answer : Option C By equating 1/RC with frequency.

When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

Why does a forward biased diode offer low resistance?

Description : Why does a forward biased diode offer low resistance?

Last Answer : The external voltage over comes the junction potential and provides an easy path for the flow of charges across the junction. Hence it offers low resistance.

What is the typical back-to-forward resistance ratio of a good-quality diode?

Description : What is the typical back-to-forward resistance ratio of a good-quality diode?

Last Answer : 10-to-1 ratio.

As a rule of thumb, what is an acceptable ratio of back-to forward resistance for a diode?

Description : As a rule of thumb, what is an acceptable ratio of back-to forward resistance for a diode?

Last Answer : Greater than 10 to 1

When the diode is forward biased, it is equivalent to a. An off switch b. An On switch c. A high resistance d. None of the above

Description : When the diode is forward biased, it is equivalent to a. An off switch b. An On switch c. A high resistance d. None of the above

Last Answer : b. An On switch

Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Description : Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Last Answer : Definition: The resistance offered by the diode to the AC operating conditions is known as the Dynamic resistance' or Incremental resistance' or AC resistance' of a diode. It is ... Dynamic resistance is actually the reciprocal of the slope of the forward characteristics.

In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Description : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Last Answer : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_ ... (a) and (b) are correct D. Both a and b are wrong

Tunnel diode is a: a) Power diode b) Has light doping c) Has heavy doping d) Is a reverse recovery diode Ans: C 76.LEDs are fabricated from: a) Silicon b) Germanium c) Si or Ge d) Gallium arsenide

Description : Tunnel diode is a: a) Power diode b) Has light doping c) Has heavy doping d) Is a reverse recovery diode Ans: C 76.LEDs are fabricated from: a) Silicon b) Germanium c) Si or Ge d) Gallium arsenide

Last Answer : Ans: D

The knee voltage (cut in voltage) of Si diode is a. 0.2 V b. 0.7 V c. 0.8 V d. 1.0 V

Description : The knee voltage (cut in voltage) of Si diode is a. 0.2 V b. 0.7 V c. 0.8 V d. 1.0 V

Last Answer : b. 0.7 V

Three capacitors with different capacitances are connected in series. Which of the following statements is TRUE? w) All three of the capacitors have the same potential difference between their plates. x) The magnitude of the charge is the same on all of the capacitor plates. y) The capacitance of the system depends on the voltage applied across the three capacitors.

Description : Three capacitors with different capacitances are connected in series. Which of the following statements is TRUE? w) All three of the capacitors have the same potential difference between their plates. x ... y) The capacitance of the system depends on the voltage applied across the three capacitors.

Last Answer : ANSWER: X -- THE MAGNITUDE OF THE CHARGE IS THE SAME ON ALL OF THE CAPACITOR PLATES

A potential difference of V = 100 ± 2 volt, when applied across a resistance R gives a current of 10 ± 0.5 ampere.

Description : A potential difference of V = 100 ± 2 volt, when applied across a resistance R gives a current of 10 ± 0.5 ampere.

Last Answer : A potential difference of V = 100 2 volt, when applied across a resistance R gives a current of 10 ... percentage error in R given by R = V/I.

A potential difference of 10 V is applied across a conductor of resistance `1 k Omega`. Find the number of electrons flowing through the conductor in

Description : A potential difference of 10 V is applied across a conductor of resistance `1 k Omega`. Find the number of electrons flowing through the conductor in

Last Answer : A potential difference of 10 V is applied across a conductor of resistance `1 k Omega`. ... of electrons flowing through the conductor in 5 minutes.

Current in a circuit if resistance of 15 Ω and potential difference of 3.0 V is applied across it's ends is A. 1 A B. 2 A C. 0.5 A D. 0.20 A

Description : Current in a circuit if resistance of 15 Ω and potential difference of 3.0 V is applied across it's ends is A. 1 A B. 2 A C. 0.5 A D. 0.20 A

Last Answer : 0.20 A

When the potential difference of 4 volt is applied across resistance, 10J energy is converted. Find the charge flows. a. 0.20 C b. 2.5C c. 5C d. 10C

Description : When the potential difference of 4 volt is applied across resistance, 10J energy is converted. Find the charge flows. a. 0.20 C b. 2.5C c. 5C d. 10C

Last Answer : b. 2.5C

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150Ω D. 2 Ω

Description : What is the input impedance of a transmission line if its characteristic impedance is 300 Ω and the load is 600 Ω? Assume a quarter wavelength section only. A. 150 kΩ B. 150 mΩ C. 150 Ω D. 2 Ω

Last Answer : C. 150 Ω

Write colour code of 1 kΩ resistor.

Description : Write colour code of 1 kΩ resistor.

Last Answer : The colour code of 1 kΩ resistor is : Brown, Black, Red

In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor

Description : In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be (A) 0.4 kΩ (B) 3 kΩ (C) 2.8 kΩ (D) 2.5 kΩ

Last Answer : In a 5 bit weighted resistor D/A converters, the resistor value corresponding to LSB is 40 kΩ, and the resistor value corresponding to MSB will be 2.5 kΩ 

If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be

Last Answer :  If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be 10.

Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Description : Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Last Answer : Ans: B

While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B