High speed diesel A) is used on high speed engine B) has lower fule value then l.s.d per litre. C)both (a) & (b) D)none of the above

High speed diesel
A) is used on high speed engine
B) has lower fule value then l.s.d per litre.
C)both (a) & (b)
D)none of the above
by

1 Answer

Answer :

C)both (a) & (b)
by

Related questions

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency

onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above

Description : onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above

Last Answer : Stationary diesel engine

variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above

Description : variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above

Last Answer : ∙ Tractor engine(diesel)

A traction fitted with diesel engine will have good slogging ability as lugging ability if it has a reserve of a.500 rpm d.200 rpm c.300 rpm e.1000 rpm

Description : A traction fitted with diesel engine will have good slogging ability as lugging ability if it has a reserve of a.500 rpm d.200 rpm c.300 rpm e.1000 rpm

Last Answer : a.500 rpm

The estimated useful life of diesel engine is: A)8 years b)10 years C)12 years d)14years

Description : The estimated useful life of diesel engine is: A)8 years b)10 years C)12 years d)14years

Last Answer : b)10 years

GOOD EARTH is one of the important make of (A) tractor (B) electric motor (C) diesel engine (D)power tiller

Description : GOOD EARTH is one of the important make of (A) tractor (B) electric motor (C) diesel engine (D)power tiller

Last Answer : A) tractor

40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Last Answer : ∙ 88-90°c

Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2

Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2

Last Answer : c) 120-200 kg/cm2

Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above

Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above

Last Answer : c) 20-35 kg/cm2

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at high speed. C. To permit the generation to deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Description : Main function of cutout relay in electrical circuit is A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces. B. To restrict the maximum output at ... deliver current to the battery or to the lightening and ignition circuit. D. None of the above

Last Answer : A. To prevent the reversal of current flow from the battery when dynamo speed (engine speed) reduces.

Piston speed for high speed engine is (a) 300-500 m/min (b) 100-300 m/min (c) 500-700 m/min (d) >700m/min

Description : Piston speed for high speed engine is (a) 300-500 m/min (b) 100-300 m/min (c) 500-700 m/min (d) >700m/min

Last Answer : (a) 300-500 m/min

peed of a high speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : peed of a high speed engine is (a) 1000rpm (d) none of the above

Last Answer : (c) >1000rpm

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Last Answer : (b) number of power stroke per minute for all cylinders

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

peed of a medium speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : peed of a medium speed engine is (a) 1000rpm (d) none of the above

Last Answer : (b) 350-1000 rpm

Speed of a low speed engine is (a) <350 rpm (b) 350-1000 rpm (c) >1000rpm (d) none of the above

Description : Speed of a low speed engine is (a) 1000rpm (d) none of the above

Last Answer : (a)

346- Side deflection of stalk can be minimized by.... (a) Having a short cutting stroke (b) Having an arrangement to obtain two cuts per stroke (c) Both (a) & (b) (d) None of the above

Description : 346- Side deflection of stalk can be minimized by.... (a) Having a short cutting stroke (b) Having an arrangement to obtain two cuts per stroke (c) Both (a) & (b) (d) None of the above

Last Answer : (c) Both (a) & (b)

For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Description : For rotary cutting blade the proper cutting quality is affected by A)rates of forward speed to blade pert pheral speed B)radius of rotation of cutting blade C)feed per blade D)all of these

Last Answer : D)all of these

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

Connecting rod of two stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Description : Connecting rod of two stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Last Answer : A. Compressive load

Connecting rod of four stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Description : Connecting rod of four stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Last Answer : C. Both compressive and tensile load

V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Description : V-belt drive transmission system is used when it is designed to achieve a) High speed ratio b) Space requirements are limited c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Description : Rotary tillers are characterized by a) Lower and negative draft b) High power requirement c) Excessive pulverization d) All the above

Last Answer : d) All the above

Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s

Description : Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s

Last Answer : b)20-40m/s

An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k

Last Answer : b) 28.8 * 10-2k

Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Description : Smaller tension ratio result in.... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Both (c) & (b) (d) Excessive belt slippage

Last Answer : (c) Both (c) & (b)

shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Description : shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Last Answer : i. Minimum tillage of trashy land at shallow depths

Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Description : Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Last Answer : a. L=[2C+( 2) (DI+D2)] + [ /4C]

For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Description : For operating rotavator on trashy soils which tines are better: A L-shaped B.Hook shaped C.Backward curved tip twist blade D.Straight blade

Last Answer : A L-shaped

The sound level of an agricultural tractor should not exceed : I. 110 dB J. 100 dB K. 90 dB L. 80 dB

Description : The sound level of an agricultural tractor should not exceed : I. 110 dB J. 100 dB K. 90 dB L. 80 dB

Last Answer : K. 90 dB

Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Description : Superchargers are driven by A. Electric current from the battery B. Exhaust gases from engine C. Direct connection with the engine power D. None of the above

Last Answer : C. Direct connection with the engine power

Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Description : Turbo chargers are driven by A. Direct connection with engine power B. Exhaust gases from engine C. Electric current from the battery D. None of the above

Last Answer : B. Exhaust gases from engine

Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%

Last Answer : A. 10-20%

which of the following tractor has the cair cooled engine? A)ford b)eicher C)international d)hmt

Description : which of the following tractor has the cair cooled engine? A)ford b)eicher C)international d)hmt

Last Answer : b)eicher

ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c

Last Answer : ∙ 71-82°c

Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2

Last Answer : a) 6-10 kg/cm2

Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3

Last Answer : (a) 1 5 3 6 2 4

Stroke bore ratio for tractor engine is (a) 1.25 (b) 1.45 (c) 1.75 (d) 2.00

Description : Stroke bore ratio for tractor engine is (a) 1.25 (b) 1.45 (c) 1.75 (d) 2.00

Last Answer : (a) 1.25

main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops more current. C. To prevent building up of high voltage in a circuit. D. None of the above

Description : main function of the current regulator is A. To prevent the reversal flow of current from the battery when dynamo speed is drops. B. To safeguard against flow of high currents to battery when armature develops ... . C. To prevent building up of high voltage in a circuit. D. None of the above

Last Answer : B. To safeguard against flow of high currents to battery when armature develops more current.

Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Description : Roller chains are used for: a)Higher speed and higher loads b)made of high grade steel c)components are harden and polished d)All of the above

Last Answer : d)All of the above

Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Description : Detonation is favoured by a. Low crankshaft speed at full throttle b. .Higher loads c. Both (a) and (b) d. None of the above

Last Answer : c. Both (a) and (b)

V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Description : V -belt are most suitable for a. less space requirements b. use with adjustable pulley foe speed change c. both (a) and (b) d. none of the above

Last Answer : c. both (a) and (b)

Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)

Last Answer : B. CI=[E/(N+E) ]×100

The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance between the speed pick up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Description : Tapper roller bearing are used in disc harrow because a) It can take heavy radial loads b) It can take both radial as well as end thrust c) It can operate effectively at low speed and in contact with dirt d) Both (b) and (c) are true

Last Answer : d) Both (b) and (c) are true

The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Description : The cutter bar of a tractor operated mower ordinarily makes: A. Near the front axis B. 40mm towards the real axis C. At the power take off shaft D. Between the two lower Links

Last Answer : D. Between the two lower Links

The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above

Description : The ideal moisture content for the soil primary tillage operation a) Upper plastic limit of the soil b) Lower plastic limit c) Wilting Point d) All of the above

Last Answer : a) Upper plastic limit of the soil