Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above
Last Answer : c) 20-35 kg/cm2
Description : Injection pressure of fuel nozzle in diesel engine is a) 30-45 kg/cm2 b) 50-100 kg/cm2 c) 120-200 kg/cm2 d) 200 kg/cm2
Last Answer : c) 120-200 kg/cm2
Description : Hand operated sprayer are operated at a pressure (kg/cm2) a) 1-7 b) 7-10 c)10-20 d) 20-55
Last Answer : a) 1-7
Description : Operating pressure of power operated sprayer E. 1-7 kg/cm2 F. 10-20 kg/cm2+ G. 20-55 kg/cm2 H. >55 kg/cm2
Last Answer : G. 20-55 kg/cm2
Description : Operating pressure of the hand operated sprayer is E. 20-55 kg/cm2 F. 1-7 kg/cm2 G. 10-20 kg/cm2 H. >55 kg/cm2
Last Answer : F. 1-7 kg/cm2
Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm
Last Answer : b) 5 cm
Description : Application rates for dusters are a.40 kg/ha
Last Answer : a.
Description : The bearing capacity of granite is generally (A) 5 to 10 kg/cm2 (B) 15 to 20 kg/cm2 (C) 30 to 35 kg/cm2 (D) 40 to 45 kg/cm2
Last Answer : Answer: Option C
Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3
Last Answer : (a) 1 5 3 6 2 4
Description : ptimum working temperature for petrol engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 71-82°c
Description : onstant speed governors are used on ∙ Tractor engine diesel ∙ Stationary diesel engine ∙ Petrol engine ∙ None of the above
Last Answer : Stationary diesel engine
Description : variable speed governors are used on ∙ Tractor engine(diesel) ∙ Stationary engine (diesel) ∙ Petrol engine ∙ None of the above
Last Answer : ∙ Tractor engine(diesel)
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above
Last Answer : ∙ Torque is a function of thermal efficiency
Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder
Last Answer : (b) number of power stroke per minute for all cylinders
Description : power spray are operated at a pressure. a. 5-10 kg/m2 b.10-20 kg/m2 c.20-55 kg/m2 d.>55 kg/m2
Last Answer : c.20-55 kg/m2
Description : The fuel in diesel engine is normally injected at pressure of a. 5-10 kg/cm2 b. 20-25 kg/cm2 c 60-80 kg/cm2 d. 90-130 kg/cm2
Last Answer : ANSWER d. 90-130 kg/cm2
Description : 40 optimum working temperature for diesel engine is about ∙ 88-90°c ∙ 71-82°c ∙ 60-70°c ∙ 90-100°c
Last Answer : ∙ 88-90°c
Description : Turbo chargers or super chargers increases engine power by A. 10-20% C. 50-60% B. 20-30% D. 90-100%
Last Answer : A. 10-20%
Description : Cutting speed of the impact type cutter is a)10-20 m/s. b)20-40m/s c)40-50m/s. d)46-56m/s
Last Answer : b)20-40m/s
Description : The specific fuel consumption per BHP hour for petrol engine is approximately a. 0.1 kg b. 0.2 kg c. 0.25 kg d. 0.35 kg
Last Answer : ANSWER c. 0.25 kg
Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm
Description : The injection pressure of ic engine used on tractors is in range of kg/cm2 1. 0-6 2. 60-120 3. 120-200 4. 200-300
Last Answer : ans 3
Description : If the width of a pavement slab is 7.5 m, thickness 20 cm and working stress 1400 kg/cm2 , spacing of 10 mm tie bars for the longitudinal joint, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : Vinyl chloride (CH2 = CH.Cl) is produced by the thermal pyrolysis of ethylene dichloride at a pressure & temperature of (A) 4 kgf/cm2 & 500°C (B) 10 kgf/cm2 & 1000°C (C) 40 kg/cm2 & 200°C (D) 100 kgf/cm2 & 500°C
Last Answer : (A) 4 kgf/cm2 & 500°C
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm
Last Answer : c) 600-800rpm
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more
Last Answer : a) Higher cylinder speed.
Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate
Last Answer : a)peripheral speed of the drum
Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660
Last Answer : a. 11
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above
Last Answer : M. Cylinder peripheral speed
Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder
Last Answer : (b) Spike tooth cylinder
Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above
Last Answer : (a) Cylinder losses
Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above
Last Answer : (a) Increase threshing efficiency
Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss
Last Answer : (d) Gathering loss
Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above
Last Answer : a) Cylinder losses
Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above
Last Answer : d) All of the above
Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss
Last Answer : (b) Shoe loss
Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss
Last Answer : (b) walker loss(rack loss)
Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss
Last Answer : (a)cylinder loss
Description : In standard disc plow the tilk angel varies between: A.30-40 ° B.40-45° C.20-25° D.2-3°
Last Answer : C.20-25°
Description : If 20 kg of coarse aggregate is sieved through 80 mm, 40 mm, 20 mm, 10 mm, 4.75 mm, 2.36 mm, 1.18 mm, 600 micron, 300 micron and 150 micron standard sieves and the weights retained are 0 kg, 2 kg, 8 kg, ... , the fineness modulus of the aggregate, is (A) 7.30 (B) 7.35 (C) 7.40 (D) 7.45
Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these
Last Answer : Answer: Option B